CATERPILLAR M318C WHEELED EXCAVATOR w/ SCRAP MAGNETFeatures: -- (2) sets of outriggers -- 48" Magnet -- Generator onboard for magnetHours: Approx. 4,536

CEFLA ROCTRE D Automatic Spray Finishing Machine for HIGH VOLUME PRODUCTION and includes (2) two integrated cleaning trolleysThickness: Max. 50 mm (2"); Min. 5 mm (0.2").Maximum Line speed: 20 MPM (65 FMP).Equipment Specifications:CEFLA, model ROC 3 D. Is a Two-arm reciprocating Spray Machine: -- Parts are fed under the Part Reading Bar to measure size and spray parameters on a continuous CFB belt conveying system. -- Lacquer recovery and belt cleaning are accomplished by means of a "cleaning trolley" located under the existing end feed belt. Made up of counter-rotating rollers with scraper and belt cleaning unit, with (3) rollers and stainless-steel troughs: all the rollers are fitted on the motorized trolley longitudinally removable by hand pulling of trolley out. -- Powered outfeed tilt-able belt lifts to approach the cleaning trolley. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, four per arm, and driven by a Brushless servo motor.There are (2) Separate lacquer feeding circuits with recycling system. -- This is a fully pressurized spray cabin with an exhaust air filtering system for overspray using a double dry filter set, primary filter, and secondary. -- Electronic control cabinet to monitor spraying functions.The booth consists of sandwich paneling, and air is pushed in through (2) air intake ducts (positioned between guns) above the slanted perforated top panels made of fine filter material, which help to reduce turbulence. Parts running through the sprayer can be viewed by means of a large front viewing window/access panel, which can be lifted to access the guns and interior of the sprayer. Photos show equipment while it was still in service - currently being reconditioned.Note: EX-FACTORY’s Logistics Department is experienced and set up to provide “Full Service Logistics"; from Overseas Suppliers to your Door. …Packaging, Container Loading, Ocean Freight, Marine Insurance (door to door).

CEFLA EASY 2000/D Automatic Spray Finishing Machine: 2010 CEFLA "EASY 2000 D" Reciprocating Sprayer: -- Sprayer fabricated using coated sheet panels, uses a Centrifugal fan for intake of room air to upper air diffusion hood inside of cabin to pressurize the spray area. -- Conveyor speeds variable from 2 - 8 MPM. Belt width capable to carry 1,600 mm (5') wide charge through the machine. -- Machine is PLC Controlled. The Superior Coating application is achieved by utilizing a "back spray" technique. The machine uses a slide-out material recovery system consisting of (2) rollers. -- Infeed & outfeed Conveyors with lift cylinders. -- Includes: (2) Reciprocating arms traveling on polished rods, hydraulic shock absorber provides smooth operation. -- Parts are read at the Infeed of the Conveyor by a photodiode light bar that reads the size of the part and sends that information to the PLC to control the Spray Gun action. -- Machine is equipped with (2) paint circuits.

CEFLA - MITO, ...Complete Spraying System with SORBINI Cleaning Brush.Reciprocating Feed Through System for Waterborne & Solvent-Borne Coatings: The max. flexibility and technology for the continuous spraying of any kind of raised panels.Features: -- Machine designed with a solid structure: LASER 3D; full accessibility, thanks to the wide use of glass superficies, access doors, and extractable parts. -- Conveying System with: CFB Belt with sealed edge, driven by inverter. -- Axis driven by the powerful brushless motor and by a sophisticated toothed belt handling system, with recycling sphere bearings. The best performances in speed, acceleration, and the softness in guns motion allows to achieve the max. application quality. -- The central axis holds: (1) Gun supporting arm (removable), equipped with quick-release (predisposed for max. 4 guns); complete with: Manual height adjustment, (3) high pressure lacquer feeding circuits with recycle; lacquer filters with stainless steel fittings. -- Exclusive pressurization flows analysis and sophisticated air diffusion plenum with double fan for air intake and filtration results in: Higher lacquer saving, better machine cleaning. Circulation provided by floor mounted MZ RLQ 560, Direct-drive 4 KW , 1755 RPM motor. -- Tanks with supporting areas for filters by COLUMBUS or ANDREAS-type filters.Electronic Scanner for: Shape reading and workpieces positioning; max. efficiency in managing the guns' spraying.TECHNICAL FEATURES:Total length of the machine: 4,650 mmTotal width of the machine: 3,850 mm (4,210 mm with fan)Machine structure height: 2,500 mmElectronic control unit with: PLC and software for machine managing.Main control cabinet: Pressurized, placed at the machine infeed, along the service side complete of cable and wiring system for connection to all the users.Spraying parameters management is operated by PLC:Working programs setup, measurements of the lacquered surface & lacquer consumption, 5" color touchscreen display for diagnostic and control; possibility to exchange data from and to PLC managing complete Lines.Possibility to manage pumps for color change/washing (up to 4 pumps). -- Comes with: 2006 SORBINI/CEFLA VS/33-ACT-F, 460/3/60 Panel Cleaning Brush with brush for the top roll followed by a nozzle blow off station. (1) Head, 53" width cap. Top brush head; features timed rotating air blowers, air liner blower with nozzles. Upper mounted Anti-static ionization bar; 400 RPM brush speed.With CEFLA TM 3000, 600/3/60 V, infeed belt conveyor. -- Line is disconnected/dismantled per last (8) photos.

DIEHL SL-55 Straight Line RipsawSpecifications: -- 15 HP - 3,450 RPM Direct drive arbor motor, 2" dia. arbor, 16" blade cap. -- 4" Max. depth of cut, 12" min. part length -- 20-1/2" width of the table to the right of blade & 30" to the left, 66" table length.Equipped with & Features: -- 3 HP 4-Step feed drive 30 - 50 - 75 & 120 FPM; -- Twin chain drive. -- Automatic drip chain lubrication. -- Top pressure system with (6) full-width rollers & (2) split rollers over the blade.

DIEHL DL-405 MOULDERSpecifications: -- 5-Head, 8-5/8" x 4-1/2" cap. -- Head sequence: Bottom 15 HP, right 10 HP, left 10 HP, top 15 HP, bottom 10 HP motor; all spindles 1-13/16" dia., belt driven at 6,000 RPM; detachable jointers on side, top, and bottom spindles, spindles reversing on side heads; -- Mechanical digital readout for left horizontal spindle & top vertical spindle. -- 5 HP Feed motor, Cardan drive, variable feed speed 22 to 135 FPM, motorized feed beam, dual action holddown, powered lower infeed and outfeed rolls, pneumatically pressured feed rolls and top chip breakers with separate regulator and gauge for rolls after the top spindle.Equipped with: -- Automatic bed lubrication, hardened bed plates, attached operator's console, sound enclosure, 77" x 9" straightening table.- Also includes dust collection manifold.

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6g DIEHL NO. 75 18" Straight Line Rip Saw Specifications: Table size 52-1/2” x 80” x 34” H. Throat 21". Distance from front of blade to table 36". Max. blade dia. 18". Adjustable arbor dia. 2". Min. stock length 12". Max. stock thickness 4-1/4". Max. depth of cut 4". Variable feed speeds 40 - 145 FPM. Equipped with: 15 HP - 3,500 RPM Blade motor. Automatic arbor brake. 8-1/4" W Dual 4" W Pyramid corrugated feed chain, with 3 HP Motor. (8) 8” W hold-down rolls, Each with (4) 1-1/2” W Segments. Upper anti-kickback fingers with Cam height control. Automatic lubrication. Complete with: 29” W x 1-3/8” H Cast-Iron Fence.

DIEHL ESL-10 Straight Line Rip Saw, with LaserSpecifications: -- Table size 39-1/2" x 52" x 35" H. -- Throat 17-1/2". -- Distance from front of blade to table 21-1/2". -- Max. blade dia. 16". -- Max. thickness 1-1/2". -- Guaranteed glue joint length 48". -- Feed speed 30 FPM.Equipped with: -- 10 HP Blade motor with Automatic brake. -- Pyramid corrugated feed chain, with 1 HP Motor. -- (5) Pairs of 2-1/2"; Dia. x 1-1/2"; W Hold-down rolls. -- 20-1/2"; L x 2"; H Fence. -- Upper & Lower anti-kickback fingers. -- Manual feed chain lubrication.Complete with: -- Installation, Maintenance & Operating Instructions. -- Laser. -- 11-3/4" Dia. Blade. -- (4) Swivel Casters.

DIEHL 55 Straight Line Ripsaw:Specifications -- 15HP - 3,450 RPM Direct drive arbor motor, -- 2" dia. arbor, 18" blade cap., 4" max. depth of cut, -- 12" min. part length, -- 21-1/2" width of table to the right of blade & 30" to the left, 43" table length. -- 2 HP 4-Step feed drive 30 - 50 - 75 & 120 FPM; twin chain drive,Equipped with & Features -- Automatic dip lubrication. -- Top pressure system with (6) full width rollers & (2) split rollers over blade. -- All cast iron machine -- Runs very nice --Complete with: Rip fence,.

DIEHL - SL-52, ...Straight Line Rip SawSpecifications: -- 15 HP - 3,600 RPM belt driven motor, fixed 2" arbor. -- 14" - 18" Blade diameter. -- 4-1/4" Max. thickness with 18" blade diameter. -- 2 HP - 1,800 RPM feed drive, variable feed speed from 65 to 190 FPM. -- 25" Throat depth to right of blade; 25" of table to left of blade. --Table size of 78" x 64".Equipped with & Features: -- Cast iron pressure bar arms with ball bearing rollers. -- Adjustable rip fence. -- Self-adjusting antikickback fingers with control cam. -- Automatic lubrication of feed chain & race. -- Full overload and under voltage protection. -- Manual arbor brake for safety with interlock; 34".Shipping Dimensions: 7-1/2' L x 7' W x 5-1/2' H; weight: 5,000 Lbs.Note from the seller: New Gear Box, new Drive Motor & Variable Speed Pulley

DIEHL SL-55 Straight Line RipsawSpecifications: -- 15 HP - 3,450 RPM Direct drive arbor motor, 2" dia. arbor, 16" blade cap. -- 4" Max. depth of cut, 12" min. part length -- 20-1/2" width of the table to the right of blade & 30" to the left, 66" table length.Equipped with & Features: -- 3 HP 4-Step feed drive 30 - 50 - 75 & 120 FPM; -- Twin chain drive. -- Automatic drip chain lubrication. -- Top pressure system with (6) full-width rollers & (2) split rollers over the blade.

DIEHL - SL-52, Straight Line Rip SawSpecifications: -- 15 HP Motor, 3,600 RPM belt driven, fixed 2" arbor. -- 14" to 18" Blade diameter. -- 4-1/4" Max. thickness with 18" blade diameter. -- 2 HP - 1,800 RPM feed drive, variable feed speed from 65 to 190 FPM. -- 25" Throat depth to right of blade, 24" of table to left of blade. --Table size: 61" x 80".Equipped with & Features: -- Cast iron pressure bar arms with ball bearing rollers. -- Adjustable rip fence. -- Self-adjusting antikickback fingers with control cam. -- Automatic lubrication of feed chain & race. -- Full overload and under voltage protection. -- Manual arbor brake for safety with interlock.Shipping Dimensions 7-1/2' L x 7' W x 5-1/2' H; weight of 5,000 Lbs.

--In auction: https://exfactoryauctions.com/Detail/SO-230040/event/A122024$1- NO RESERVE!-- GRECON/DIMTER OPTICUT 204 L Optimizing Cutoff System NOTE: Currently De-installed Specifications: For hard or soft wood. Left-to-right feed. Max. crosscut section 7-3/4" x 1-15/16" to 5-3/4" x 3-1/16". Board width cap. 1-1/5" to 7-3/4", Board thickness 3/8" - 3-1/8", Board length 15" to 20'. Shortest fixed length 5-3/8", Shortest finger jointing length 5". Max. feed speed 750 FPM. Average production rate 36,000' running length/shift. Equipped with: Blade dia. 19-1/2", with 10 HP - 4,100 RPM Motor. 10 HP Servo drive feed motor, (3) Pneumatically-operated top rollers & (1) Driven bottom drum roller. Control, with LCD display & Touchpad. Complete with: 12" W x 23-1/2' L Infeed Belt Conveyor, with Double wheel measuring system & Top mounted luminescent camera, Detects crayon defect marks up to (8) grades. 12" W x 34-1/2' L Outfeed Belt Conveyor, with (4) Sorting stations, with Encoder pulse-controlled kickers, Kick singularly or in batches of 2 or 3 for larger heavier boards. PC-Based Control.

DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end where a NRS-20 Rotary Air Lock where dust is discharged into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DIXIE - 15 HP: Dust Collector Specifications: -- 15 HP Motor. -- 1,760 RPM. -- Air Pulse filter bag cleaning System. -- (2) Bottom outlets. -- 15" Diameter: Inlet pipe size. -- Wall-mounted motor control station. -- Overall Collector footprint: 90" Wide x 67" deep (101" with rear-mounted fan) x 122" high.

DONALDSON / TORIT - 2DF-16, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes "New" AirMax Premium Media Cartridge Filters: Fire retardant. -- Total filter media area: 3,616 ft². -- Air-to-Media ratio @ 8,000 CFM is 2.2:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. -- (2) Hopper outlets with sealing drum cover kits. -- Steel support structure. -- Includes: 20 HP Top mount, direct-drive Blower. -- Rated for 8,000 CFM. -- Electrical motor starter & controls. -- Includes: Installation/Operation/Maintenance Manuals.Sold with 6-Month Mechanical Warranty

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DOOSAN DX300LC-3 LONG REACH ExcavatorSpecifications: -- Engine Type: Doosan Horsepower: 213 HP (159 kW / 216 PS) -- Engine Cylinders: 6 -- Boom reach: 60' -- Track width: 33.5" -- Hours: 2,800Equipped with:60 ft long reach boom60" Bucket

DOOSAN DL220-5 Wheel LoaderSpecifications: -- Engine: 160 HP -- Bucket Width: 8.37ft in -- Fuel Capacity: 58.7 gal -- Max Speed - Forward: 24.3 mph -- Hours: 5,514

DOOSAN DX85R-3 Compact Crawler Excavator with Brush CutterSpecifications: -- Yanmar Engine: 59.4 HP (44.3 kW ) -- Max. torque at 1365 RPM 24.6 kgf/m (241 Nm) -- Max. swing speed: 9.5 RPM -- Boom swing angle: L/R 70° / 55° -- Travel speed: (low - high) 1.6 to 2.92 MPH (2.7 - 4.7 km/h) -- Maximum gradeability: 35° / 70% -- Hours: 350 (in use)Equipped with: -- 50" MTL XC5 Brush Cutter -- 60" Ditching bucket -- 36" Digging bucket -- 24" Digging bucket -- Hydraulic quick coupler -- Hydraulic thumb -- Front blade -- Roll Over Protective Structure (ROPS) -- Pressurized, sound-insulated cab -- Adjustable seat with adjustable headrest and armrest -- Air conditioning -- Pull-up type front window and removable lower front window -- Sliding right windows with lock -- Ceiling light