HOMAG - EDGETEQ S-380/1660 6.6 Edition: Edgebander w/Premill & Corner Routing + EVA/PUR Gluing TechnologySpecifications0.4 - 12 mm (0.016 - 0.47") Edgeband thickness; 8 - 60 mm (0.31" - 2.36") panel thickness for EVA/PUR; 40 mm.60 mm (6-1/4") Min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: Premilling Station. (2) Motors @ 2.25 kW (3.0 HP) - 12.000 RPM; LH & RH rotation with: Pneumatic jump control for chip free & clean panel edges.Includes: Diamond cutterheads. -- Infeed fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit: Between glue roller & pressure section. -- Automatic Edge Magazine. Strip & coil stock: Strips 0.4 mm - 12 mm (0.016 - 0.47"); coils up to 3 mm PVC & "HD" guillotine. -- "QA-65N" Quick Melt EVA/PUR, pre melter gluing technology with: Auto-Purge function; "Quick Change" Glue Tank for maintenance & glue color change. -- Pressure Section1st Roller driven, plus: (3) Idle rollers; lube spray unit on last pressure zone roller for high gloss peel coat processing; timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 20 MPM (26 - 66 FPM); 14 MPM (46 FPM) when using contour trimming. -- Operator InterfaceHOMAG "Power Touch Control": Memory 256 MB RAM; 1 GB flash card drive. 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations End Trimming: (2) Motors @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel: 0°- 15°. -- MS-40 Multistage. Flush/Bevel-Fine/Radius Trimming Unit: Top/Bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto tilt positioning 0° - 25° with: Combination flush/radius/chamfer cutterheads.Horizontal & Vertical tracing wheels equipped w/brushless multi axis Servo motors for: Positioning of work unit & horizontal copy wheels for quick changeover. Includes: (4) Positioning options: Profile-1, Profile-2 = bevel & flush trimming.Auto Tilt & Servo control for: Edge thickness; nested top copy system. -- MF-50 Multifunction Contour/Corner Rounding Unit. (2) Motors: 0.35 kW (1/2 HP) - 12,000 RPM w/"Soft Touch" Magnetic Linear Drive System for: 1-Mil, 2-mil & 3-mil thickness.For leading & trailing edges vertical corner rounding of panels: Either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- MZ-40 Multistage Scraping; Multi profile (PVC). Top/bottom with: (2) Radii profiles: 1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. Nested Top Copy System. PVC Scrape collection box. -- Scraping Glue Unit. Flush top/bottom on panel surface with: Floating insert knives. -- Buffing Unit. Top/Bottom: (2) Motors: 0.10 kW (0.125 HP) - 2,800 RPM. Complete with:Separating spraying/cleaning agents; motorized, programmable hold-down pressure beam; padded sound enclosure; isolation transformer for multiple input voltages; used tooling; Original Factory Machine Documentation. -- Actual M

HOMAG - KAL 210 AMBITION 2262: Edgebander (w/Premill & Corner Rounding) -- SpecificationsCoiled stock min./max. Edge thickness: 0.3 - 3 mm (0.012. - 0.118"); strip material min./max. edge thickness: 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min./max. thickness:12 - 40 mm (0.472" - 1.574"); panel overhang: 30 mm (1.18"). -- Infeed Fence. Adjustable infeed fence with: Manual digital indicator positioning. -- Premilling Station: (2) 3.0 kW (4.0 HP) 150 Hz - 9,000 RPM Motors; equipped with: Trimming column, (2) horizontal & cross slides with: Spindle adjustment; electropneumatic horizontal jump movement of the 1st motor.Includes: Electronic frequency inverter for control of motor speed & braking; (2) dust extraction hoods; air jet panel blow off device, & SIKO digital counters for adjustments. -- Panel Preheater: Brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multipurpose Magazine: 2-Coil magazine expands capability by running coiled material & strips; magazine height adjustment allows for greater usage of varying panel heights by raising & lowering the magazine table, allowing the Operator to center the panel on the edgebanding. -- Gluing System (EVA - Hot Melt): QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper & lower unit.34 mm Dia. Glue Roller": Allows excellent control of temperature for optimum bonding results with individual adjustment for: Leading & trailing glue gates; lower melting unit equipped with: Automatic glue level control. Melting capacity: 12 kG/Hr (26 Lbs/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo); (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers; pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 kW (1.0 HP) x (2) 200 Hz - 12,000 RPM Motors to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & Bottom Flush Trimming Unit. Top & Bottom: 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; height adjustment with the top pressure beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit: FF 12. Multifunction 0.4 kW (0.54 HP) x (2) - 12,000 RPM motor to fine trim the edge overhangs at the workpiece upper & lower edge, as well as trimming around the front & rear vertical edge. - Max. feed speed: 20 MPM (65.6 FPM). -- Profile/Bevel Scraping Unit PN 10. Top & Bottom for: Thick PVC/ABS; pneumatically activated/adjustment. -- Flat Glue Scraper Unit. Top & Bottom: Pneumatically activated to remove potential glue squeezeout. -- Buffing Unit FA 11. Top & Bottom: Edge buffing/polishing; pneumatically activated. -- Operator & Machine ControlHOMATIC - PC 22: Power Control w/Touchscreen. Controller functions in Windows environment and features: Keypad w/LCD flatscreen display, fault diagnostic, OS9 real-time Operating System.Handheld remote c

HOMAG - KDF-440C: Edgebander (Premilling & Corner Rounding w/HIGHFLEX Automated package & Nitrogen Box -- Edge & Workpiece Capacity0.4 - 8 mm (0.016 - 5/16") Edge; 8 - 60 mm (5/16 - 2-3/8") panel thickness; 160 mm (6-3/8") min. panel length; 70 mm (2-3/4") min. panel width.Equipped with: -- Premilling Station: (2) Motors @ 2.25 kW (3.0 HP); 12.000 RPM; LH & RH rotation w/pneumatic jump control for chip-free & clean panel edges. Equipped with: Diamond cutterheads. -- Infeed Fence with: Servo motor positioning. -- Infrared Radiant Quartz Heating Unit between glue roller & pressure section. -- Automatic Edge Magazine for: Strip & coil stock; strips 0.4 mm - 8 mm (0.016 - 5/16"); coils up to 3 mm PVC; "HD" guillotine. -- "Quick Change" Glue Tank for: Maintenance & glue color change. -- Air Tech hot Air System. -- Pressure Section. 1st Roller driven plus: (3) Idle rollers, timed pneumatic pressure controlled; Servo motor positioning for programmable edge thickness changeover. -- Feed Speed: Variable 8 - 14 MPM (26 - 46 FPM); 11 MPM (36 FPM) when using contour trimming. -- HOMAG "Power Touch Control. Memory: 256 MB Ram; 1 GB Flash Card Drive; Operator control panel with: 22" Color HD widescreen; soft keypad; internal modem for remote diagnostic link.Workstations -- End Trimming: -- (2) Motor @ 0.35 kW (1/2 HP) - 12,000 RPM; automatic chamfer from control panel: 0°- 15°. -- Flush/Bevel Fine/Radius Trimming UnitTop/bottom (2) motors; 0.55 kW (3/4 HP) - 12,000 RPM; auto tilt positioning: 0° - 25° with combination: Flush/radius/chamfer cutterheads; horizontal & vertical tracing wheels; equipped with: brushless multiaxis Servo motors for positioning of work unit & horizontal copy wheels for quick changeover.Includes: (3) Positioning options: Profile 1, profile 2, and flush trimming. -- Corner Rounding Unit(1) Motor: 0.35 kW (1/2 HP) - 12,000 RPM for: Leading & trailing edges vertical corner rounding of panels; either radius or chamfer cutters can be mounted; 3 mm max. edge thickness. -- Scraping, Multiprofile (PVC)Top/Bottom with: (2) Profiles; 1 mm & 2 mm or 3 mm instead of 2 mm; Servo control positioning of vertical & horizontal copy wheels. PVC scrape collection box. -- Scraping Glue UnitFlush top/bottom on panel surface with: Floating insert knives. -- Buffing UnitTop/bottom (2) motors: 0.10 kW (0.125 HP) - 2,800 RPM. -- RIEPE Anti-adhesion. -- RIEPE Detergent.Complete with: -- Motorized, programmable holddown pressure beam; padded sound enclosure; used tooling; Original Factory machine documentation. -- Portable Nitrogen Box, For temporary glue pot storage to prevent hardening of PUR Glue. -- Actual Model: HOMAG - OPTIMAT KDF 440C (corner rounding). NOTE: Available early Dec/2025; possibly earlier.Machine Dimensions: 222" x 36" x 69" H.Transformer Dimensions: 24" x 31" x 32" H.

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

Houfek Maxx 1100 2 Head Widebelt Sander43 width cap Drum, Combination headHead Configuration1st Head : Contact roll2nd Head : Combination contact roll and finishing platen.Specifications -- 1st Head: 6" Dia. rubber covered contact roll, 25 HP motor; -- 2nd Head: Combination head with rubber covered contact roll 6" Dia. and air cushioned finishing platen, timers control platen inflation and deflation, 20 HP motor. -- 43" x 75" Abrasive belts, -- TRU-TRAK solid state belt tracking, -- Variable feed speed with inverer control 15 - 45 FPM -- 1 HP motor, endless belt conveyor with automatic tracking. Equipped with & Features -- Motorized part thickness opening with LED 0" - 6" opening. -- Infeed and outfeed rubber covered holddown rolls, -- Infeed over thickness bar, -- Emergency stops at infeed & outfeed, -- Air operated disc brakes on sanding heads, -- Electrical interlocks on main access doors, and motor load meters.Note from Seller :This machine was damaged by the straps going over the machine during transport. The doors work fine, they just have dents on the top where the straps dented them. Price has been reduced to reflect this (cosmetic) damage.

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HURST - SERIES 45. Boiler: Natural Gas -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox. -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with: National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency. -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with: Factory pre-piped, wired, and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are Factory packaged with: Operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: (1) 6 m³/Hr cap. vacuum pump for high-flow work table; Jib Crane & hoist to support the edgebanding head; Thermo-control for glue temperature; Foot pedal control to initiate automatic cycle.

LARICK 120 Single Spindle Profile Sander;Sands raised panels, and door edges.Specifications: -- 1" Dia. x 4" long belt driven arbor; 700 - 1700 RPM variable speed, 1 HP motor. Arbor is vertically adjustable. -- Complete with: 25" x 22" butcherblock maple table, enclosed fabricated steel base and large hand wheels for easy spindle adjustment. -- Includes: Sensing safety guard for anti-automatic restart protection.

Single head; 1.5 HP TEFC direct drive motor, spindle tilts 60° forward & 40° backward, inverter controlled variable speed from 400 - 1,800 RPM, RPM display; 4" vertical & horizontal spindle adjustment. -- Features: 36" x 33" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust hood w/piano hinge for easy ascess to sanding disc, stationary fence, large hand wheels for easy spindle adjustment.

Single head; 1.5 HP TEFC direct drive motor, spindle tilts 60° forward & 40° backward, inverter controlled variable speed from 400 - 1,800 RPM, RPM display; 4" vertical & horizontal spindle adjustment. -- Features: 36" x 33" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust hood w/piano hinge for easy ascess to sanding disc, stationary fence, large hand wheels for easy spindle adjustment.

Single head; 1 HP Belt drive motor, Fixed spindle, Mechanical controlled variable speed from 700 - 1,700 RPM, 4" vertical spindle adjustment. -- Features: 27" x 25" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust port, large hand wheels for easy spindle adjustment.

LARICK 360A Profile SanderSpecifications: -- Single-head Profile Sander;1.5 HP TEFC motor belt drives spindle which tilts 45° forward & 30° backward; -- 400 - 1,800 RPM mechanically controlled variable speed; 4" vertical & horizontal spindle adjustment. -- 36" x 33" Solid wood table top, 36" table height; 1" dia. x 4" long spindle accepts standard sanding discs, but are designed for LARRICK profile discs made to customer specifications. -- Complete with: Enclosed fabricated steel base, dust hood w/piano hinge for easy access to sanding disc, Stationary Fence, and large handwheels for easy spindle adjustment.

LARICK - 2-Head Brush Sander (2017)Machine features: (2) 15" Counter-rotating & rotation reversible heads enclosed in a Dust Collection Shroud. -- Feed belt & sanding head speeds: Variable by means of VFD. -- Machine currently setup with a steel brush & brass insert head. -- Can be used for distressing (bring out the natural grain) or denibbing (with nylon type brushes: not included). -- Head driven by: (2) 2 HP Direct drive motors. -- Current heads: Wire brush on the 1st head & brass inserts on the 2nd head.

The Model 390 Automatic Shaper is a New concept in shapers. -- This "New Shaper" is conveyor fed, making it ideal for shaping small parts which could not be fed with a conventional Power Feeder. -- The 7.5 HP inverter controlled variable speed shaper can shape pre-arched panels automatically. Using a Template, it can also hog out arched panels. -- Horizontal and Vertical shaper adjustments with digital position indicators and the 5-position fence make profile changeovers extremely quick and simple. -- Standard stack tooling spindle -- Optional upgrade to 460 V, additional $ 250.