DISA CS-4 MAXI Dust collector with Rotary Air Lock. Approx. 16,000 CFM at 8.7:1 air-to-cloth ratio; 1,725 sq. ft. of filter area, with (128) filter bags filtering to 3-micron. -- General Info: CS-4-M consists of (3) filter modules & one entrance module. -- Comes with: DISA, S56-500 Material Handling fan powered by 50 HP TEFC motor. Fan nominal rating: 16,000 CFM @ 9" SP. Fan is currently mounted on elevated support but can be installed on the ground as well. -- (3) Reverse air bag cleaning modules with motorized fans that clean the bags every (4) hours of operation automatically, each with 2 HP fan motor. A damper at inlet closes during cleaning cycle to prevent blowback. -- Complete with: Hopper bottom as collected dust is conveyed to one end where a NRS-20 Rotary Air Lock where dust is discharged into Transfer fan. Filtered air return unit, 8' support structure to allow for dumpster under Dust Collector. -- Includes: Control panel, motor starters and switches, and Explosion Panels. Material handling main fan w/motor mounted to side of base module. -- 26" diameter inlet pipe, 97" clearance under collector for dump hopper, free standing steel bolt-together structure, -- Features: Dust transfer from bottom of Rotary Air Lock to enclosed container by separate floor mounted material handling fan, approx 7.5 HP. -- Note: Pictured storage bins are not included.

DISA - NFK 9, ...2BL Modular Dust CollectorUp to 45,000 CFM @ 6.25 to 1 air-to-cloth ratio and @ 11.6" w.g. external static pressure; modular, expandable Heavy-Duty Baghouse. -- 7,200 Sq/ft of filter area, made up of (450) filter bags. -- Filter consists of: (9) Filter module sections with: Access door in each section; (2) blank inlet module sections (9) 2 HP Regeneration fans for cleaning of filter media and (2) blank entry modules. -- Includes: (1) 60 HP Belt drive COMBIFAB blower package with: Drive guards; motor & fan are a common steel base/frame with ground level installation; fan delivers about 20,000 CFM. There is sufficient filter capacity for at least 75 - 100 HP second fan/motor. -- Complete with: Outside separate electric disconnects for each cleaning fan. -- "NRS-10" Rotary Air Lock for bottom discharge with: 2 HP TEFC Motor; steel support members dismantled. -- Includes: Some outside pipe (and main headers explosion/access doors). -- NOTE: (2) Cleaning fans are missing and will be supplied at cost. -- Actual model is: NFK2000 9+2 BL HJLR.

DONALDSON / TORIT DWST6-5 Cartridge Dust CollectorDownflo® WorkStations (DWST) fit anywhere on the plant floor and apply NO restrictions to worker movements or visibility. The full line of WorkStations are designed specifically for those in-plant areas where dirty and/or noisy operations are out in the open—grinding, sanding, chipping, batch mixing or welding. The DWST delivers exceptional performance in metalworking, woodworking, and process applications where high filtration efficiency and ledge less construction is often a requirement. Specifications: -- (5) Module System, each with 10 HP motor, 7,000 CFM. -- (4) Ultra-Web cartridges. -- Pulse-cleaning manifolds and ventures, (2) dust drawers. -- (1) Acoustical panel per module. Louvers mounted on lower section of unit.Includes: -- (1) IEC control panel includes 460-volt motor starters, circuit protection for each motor, transformer, programmable logic controller. -- Magnehelic gauge mounted in a panel door, start/stop buttons, and a through-the-door disconnect switch. -- Pulse cleaning can be continuous or after-shift. -- All components are IEC rated. The enclosure is rated Type 12. -- 1"; Compressed Air Regulator with Filter Separator and Gauge, Black Iron Fittings, and Black Iron Piping Required for Cleaning System. -- Provides a 1"; Common Connection Point for Design Shutters to Tie into with Existing Compressed Air System.

DONALDSON / TORIT - 2DF-16, ...Cartridge Dust CollectorSpecifications: -- Holds (16) cartridge filters. -- Includes "New" AirMax Premium Media Cartridge Filters: Fire retardant. -- Total filter media area: 3,616 ft². -- Air-to-Media ratio @ 8,000 CFM is 2.2:1. -- Automatic Pulse Clean System with: Differential pressure gauge and sequencing control in enclosure. -- (2) Hopper outlets with sealing drum cover kits. -- Steel support structure. -- Includes: 20 HP Top mount, direct-drive Blower. -- Rated for 8,000 CFM. -- Electrical motor starter & controls. -- Includes: Installation/Operation/Maintenance Manuals.Sold with 6-Month Mechanical Warranty

DOUCET 12-SECTION Clamp Carrier (Hydraulic)Specifications: -- (12) Sections, 8-1/2' width, -- (9) Clamps per section (108) clamps total, -- 36" Clamp opening (rapid change) with 2-1/2" high jaws.Complete with: -- 5 HP hydraulic power pack and motor for rotation -- Hydraulic clamp tightening; -- Pneumatic overhead panel flattener.Note: Tear down not included

"NEW" Doucet RC - STOCK Gluer - Table top unit for glue applications on a smaller scale. Motorized stainless steel roller equipped with a 2 Litre capacity reservoir easily removable for clean up. -- Spread roller: Stainless steel with roller dimension 8" X 3 1/2"; speed of roller 50 FPM. -- Table top dimension: 20-1/2" x 13".

DOUCET FX 150 Automatic Feed to Finger JointerModel "MT-10-GD" automatic feed to Finger Jointer, chain feeding system driven on the bottom and right-and-left sides, feeds boards up to 6" max. width. -- Model "FX-150" right-hand Shaper section: Cap. 3/4" - 2" max. thickness, 1-1/2" - 8" max. width (with lugs on 12" centers, 6" max. width on 9" centers), 5" min. - 96" max. length. -- Equipped with: 5 HP Trim saw, 15 HP Shaper motor, PLC controls on shaper section, dual feed chain with lugs on 12" centers, 45 FPM fixed feed speed, 5 HP feed drive, PLC controlled extrusion type glue applicator with 12-gal. tank, sound enclosure and cabinet type base. Transfer to the assembly press. -- Includes: Stainless friction plates on assembly table, board holddown on all (4) sides, sound enclosure, cabinet type base and all protective hoods, (1) 8-bolt cutterhead with knives and setup stand. -- Approx. 8,000 linear ft./shift or more based on 12" average infeed length.This unit has no control panel

DOUCET - 16-SECTION: Clamp Carrier (Hydraulic)Specifications -- (16) Sections; 8-1/2' width. -- (6) Clamps per section; (86) clamps total. -- 32" Clamp opening (rapid change) with: 2-1/2" High jaws.Complete with: -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening. -- Pneumatic overhead panel flattener.NOTE: Tear down included!

DOUCET DRAWER MASTER DWM-36 36" Universal Drawer Box Assembly Clamp Specifications: Assembles drawers with Standard Finger-Type Dovetails, Sliding-Type Dovetails, Bored & Doweled Drawers, and Tongue & dado box joints. Cap. 10" H x 24" W x 36" L. Equipped with: Fixed left jaw, Manually adjustable right jaw, with Rapid set jaw opening. Double-acting pneumatic cylinders. 2-Hand push-button operation. “Quick” Mode & "Progressive Compression" mode, Operates as a jog button to allow for easy fitting of bottom panel in lateral grooves. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET BT3-30-5-23-G-PT Return Conveyor for Edgebanders Specifications: Right-hand feed, with Left-hand return. Min. part size 4" x 12". Max. panel size (with operator assistance supporting then turning panels) 45" x 96". Equipped with: 1-1/2’ L Infeed roller conveyor section, with (5) 23-1/4” W & (2) 34-1/4” W Rollers. 34-1/4” W x 5-1/2’ L x 35” H Receiving table, with Automatic/Manual height adjustment 2". (8) 3/8” Dia. transfer belts, (3) on 3” Centers, (2) on 6” Centers, & (3) on 9” Centers. 29-1/2” W x 5-1/2’ L x 34” H Return table. 29-1/2” W x 18’ L x 34” H 3-Section Return conveyor, with 5-1/2” W x 6’ L Gravity roller conveyor side extension. All rollers 1-7/8” Dia. covered line shaft on 3” centers. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

DOUCET SDM-M-30-72 Frame and Cabinet Door ClampDesigned for quick and accurate clamping & squaring of miter and regular cabinet doors.Specifications: -- 5-1/2" x 12-1/2" Min. door size, 30" x 72" max. door size. -- (1) Fixed vertical clamp, (2) mobile vertical clamps on roller bearings for effortless positioning. -- (1) Mobile horizontal clamp with a unique "gas spring" assisted lever for effortless centering; pressure is distributed with 4' dia. air cylinders. -- "Progressive Flow" clamping system @ 80 PSI; 675 Lbs of clamping pressure per clamp; operator working height adjustment.

DOUCET - DRAWER MASTER DWM-36: 36" Universal Drawer Box Assembly ClampSpecifications -- Assembles drawers with: Standard finger-type dovetails; sliding-type dovetails; bored & doweled drawers; tongue & dado box joints. -- Capacity: 10" H x 24" W x 36" L.Equipped with: -- Fixed left jaw, manually adjustable right jaw; Rapid set jaw opening. -- Double-acting pneumatic cylinders. -- 2-Hand push button operation. -- “Quick"; Mode & "Progressive Compression" mode; operates as a jog button to allow for easy fitting of bottom panel in lateral grooves.

DOUCET - 8-SECTION, ...Clamp Carrier (Hydraulic). -- (8) Sections, 8-1/2' width. -- (8) Clamps per section, (64) clamps total. -- 42" Clamp opening (rapid change) with 2-1/2" high jaws. Complete with: -- (1) Pneumatic fence w/manual valve. -- 5 HP Hydraulic power pack and motor for rotation. -- Hydraulic clamp tightening; mounted on rail. -- Pneumatic overhead panel flattener.Actual model is: SRH 08-8.5-64-42R.Note: Tear down and loading not included.

DOUCET ERS-96/RS-75/AP-508 MULTI-BLADE PANEL GROOVE/RIP SAW SYSTEM:The Doucet ERS-96/RS-75 Automated Panel GROOVE/RIP Saw System is designed to GROOVE and/or RIP panels as well as edge the sides of core materials. Ideal for plywood, OSB, MDF, HDF and other composite panels.This Line was originally designed for Engineered Flooring Blanks.ERS-96 Grooving Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 96" maximum. Material thickness 0.5" - 0.625" maximumGrooving pattern on 4" centers across the 96" width of panel. Depth and width of groove approx. 3/16" kerf/width by 1/8" deep.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). RS-75 Ripping Specifications:40 HP - 3,500 RPM belt driven saw arbor motor. Material width cap. 60" maximum. Strip width cap. 2.5" minimum. Depth of cut 0.25" - 0.75" (6 - 19 mm) maximum.3" dia. Arbor shaft with 1.5 HP motor for motorized arbor adjustment for panel thickness. Saw arbor accessible from above for tool changes. -- Feed system:Doucet AP-508 Automatic panel feeder with scissor lift to automatically feed panels as needed.5 HP - 1,750 RPM feed motor, variable feed speed up to 75 FPM.(4) Powered bottom feed rollers & adjustable top idler pressure rolls with positive panel support during grooving operations.Top & bottom feed rollers have slip resistant urethane covered rollers, feed rollers are chain driven with air tensioning. -- Operator Interface: Doucet OI/HMI Control System for automatic loading & stacking with minimal human intervention other than a forklift operator to bring in new material and remove the processed parts/strips. -- Complete with:Dynamic saw arbor brake; Infeed anti-kickback fingers; Saw blade safety interlock cover; 12" dia. dust collection outlet (4,000 CFM required). -- Options Include: (1) Doucet AP-508 Automatic panel feeder with Indexing scissor lift. (1) Cross Transfer Chain Conveyor to feed panels sideways by the long edge through the Groover, max width 96". (1) Cross Transfer Chain Conveyor to feed panels short end wise through the panel RIPSAW, max. width 60" (1) Outfeed Lift Table to automatically stack ripped strips. Maximum weight of stack: approx. 5,000 LBS. -- Actual Model is DOUCET RS-75/ERS-96/AP-508

DOUCET MFE 300 Lateral chain feeder for moulders and optimizers -- 3'0" x 16'-0" working deck for material length 2'0" - 16'0"; width 2" to 9.5" and thickness 1/2" to 4". -- Feed system: Hydraulic variable speed 50-300 FPM with a 20 HP power unit. In-feed (4) roller accelerator; (2) top steel rollers and (2) bottom drive roller. Additional idler rollers along feed fence to support lumber during feeding. -- Chains: Transport length of lateral chain feeder 3'0". (8) strands of C2060 chains on pneumatic up/down device to release lateral pressure on board when feeding. -- Pedestal: Feeder controls mounted to pedestal with extended cable. Interface relay to stop feeder when moulder is stopped. -- Adjustments: Tool less adjustment handles for quick setups. Easy access to for thickness adjustments at front side of feeder. -- AVAILABLE OPTIONSOne (1) set of four (4) feeding wheels made of steel with hardenedsurface teeth $ 1 000.One (1) set of four (4) feeding flat wheels made of steel, 2" wide insteadof 1" for wide material feeding $ 500.One (1) set of four (4) feeding flat wheels made of steel 1" wide $ N/C.Guiding Tunnel between feeder and moulder,Standard Guiding Tunnel (4' long) $ 1 650.Standard Short Guiding Tunnel (32" long) $ 2 100.Complete Guiding Tunnel (4' long) $ 2 700.Complete Guiding Tunnel with adjustable fence (4' long) $ 3 800.Motorized Guiding Tunnel (4' long) on request.Additional chain transfer length capacity (up to a maximum of 6additional feet) For MFE-300-16 sold per foot $ 1 685. Note: More than 6 add. feet: price upon requestSteel plates between chainsFor MFE-300-16 $ 1 050.Platen chains recommended for softwood speciesFor MFE-300-16 $ 2 850.One (1) additional chain for shorter material down to $ 1 750.18" min. lengthPressurized lateral guide with roller bearing end $ 1 400.Powered lateral guide with roller and side guides on request.Custom working height on request.

DUBOIS Vertical Edge Fill System with Micro UV This machine is designed to fill voids and defects in edges for a smooth, quality finish. These coaters are ideal for filling porous open grain panels like oak, veneers, particleboard, and MDF. Compatible with solvent based, water based, and UV fill coating.1.1 One (1) Continuous chain transport system- Top and Bottom chain transport conveyor with speed matching attachment conveyor chain- Aluminum backed chain pads with EPDM covering1.2 Two (2) double sided vertical edge denibber/buffer- Operator side Adjustable up to 12"; wide, back side fixed edge- Post mounted vertical denibber head- 12"; dia. x silicon impregnated scuffing wheel, buffer wheel to be determined- Dust hood with 4"; connection- Vertical head oscillation for even brush wear- Inverter controlled drive provides speed control for brush and oscillation1.3 Two (2) double sided vertical edge fill stations- Operator side Adjustable up to 12"; wide, back side fixed edge- Electric motor driven Applicator and Doctor roll drives- Quick change applicator sleeve design, 1-1/2"; face- Stainless steel distribution pipe with spring tension- 9"; dia. chrome plated reverse roll- Stainless steel catch pan and drain lines- 3/8"; pail mounted pump and agitator- Spring loaded doctor bar, urethane dr. blade- Air cylinder dr. roll engagement with stroke adjuster- Inverter controlled drives provides speed control for applicator and doctorrolls1.4 Edge Cure UV Oven Banks- Each bank to consist of Two (2) double sided Fusion F600 Microwave UVovens- Space for two (2) future double sided Microwave UV Units- Individually adjustable three (3) position lamp power selector switch(300, 400 & 600 w/in.)- Irradiator cooling exhaust fan for each set of four (4)2. Control Panel System- NEMA 12 Hinged Door Enclosure, with disconnect, required fuses, door mounted buttons and cooling fans- Allen Bradley HMI, PLC items included- Top mounted panel cooling fan- Required Inverters· Edge Fill Finishing Machineo Top and Bottom Conveyor driveso Denibber/Buffer Brusheso Denibber/Buffer oscillatorso Applicator Rollso Doctor Rollso Reverse Rollso UV oven Exhaust fansDesign Parameters- Machine is located in Explosion Proof Area- Voltage= 480 V., 3 Ph., 60 Hz.- Design Speed = 70 - 200 FPM- Line height = 36";- Max./Min. Part Width: 12"; / 2";- Max./Min Part Length: 245"; / 24";- Max./Min Part Thickness: 1-1/4"; / 3/8";- Paint Color· Main Frame and Conveyor: Blue / TS White· Guards: safety yellowNotes:- ¼"; product has the potential of being processed in this machine but has less probably of being successful the wider the product.

The Dubois SP-12 Linear Spray Machine is an automated linear finishing machine that can be used for a variety of applications including priming, staining, sealing, lacquering, etc. of linear stock. This spayer comes with (3) three arms, (3) three guns and (1) one paint pump. The guns are Binks spray guns Model 363, and Binks pump.Compatible with both waterborne and solvent based coatings --Three adjustable gun arms --9’-0"; long variable speed live roll conveyor w/ electric powered drive --Pneumatic gun trigger mechanism to automatically trigger guns on/off --Infeed guide fences --Top roller hold-down on infeed table --Ability to enable/disable individual guns --Easily cleaned spray trough --Adjustable atomizing air pressure --Adjustable fluid pressureIncluded optional features: &#9679 Stain wipe station mounted to outfeed with stain wipe brush &#9679 Exhaust system with spray enclosure, exhaust fan, & exhaust filter system &#9679 Denibbing station mounted to infeed

DURAMAC - DUR52-2, ...2-Head Wide Belt Sander2-Head Wide Belt Sander with: Drum, combi-head, and brush cleaner. -- Max. working width: 52". -- Max. working thickness: 6". -- 23" Infeed load space. -- 50" Wide rubber conveyor belt size. -- 1st Head: Grooved rubber contact sanding drum; 40 HP, 230 Volt - 3-phase drive motor. -- 2nd Head: Combination contact drum & polishing platen; 30 HP, 230 Volt - 3-phase drive motor. -- Spring-loaded pinch rollers. -- Electronic belt tracking, pneumatic belt tensioning. -- (1) Rear top outfeed panel brush cleaning head, 0.5 HP, 230 Volt - 3-phase drive motor. -- Power raise & lower of worktable. -- Inverter driven feed works drive motor for variable speeds, 0 to 60 FPM. -- Front operator control station; motor ammeters. -- TOSHIBA Feedworks inverter. -- "DP-626S" electronic digital readout for setting table heightAlso Available: -- Transformer for 600 Volt operation, 112.5 KVA.

DUST TECHNOLOGY DT-200 Modular Dust Collector W/ Chip TransferFree-standing self-contained internal air system.Specifications: -- 20 HP Motor, rated for 7,500 CFM. -- (4) Upper cloth filter bags with 132 sq. ft. filter area; 14" inlet dia., dust baffling system to fill bags evenly. Includes; -- (2) Rotary Air Lock units with hoppers. 8" Bottom discharge openings. -- (1) Fan box (DT-FB-100) w/ 10 HP, 4,450 CFM blower unit w/ 12" main inlet diameter. -- (1) Master control panel. Made in the USA. Three Year Comprehensive Warranty

DUST TECHNOLOGY DT-250 Modular Dust Collector Free-standing self-contained internal air system, 25 HP Motor;Specifications: -- Rated for 9,800 CFM, 5-bag unit, 75 cu. ft. collection capacity. -- (5) Upper cloth filter bags with 165 sq. ft. filter area; 16" inlet dia., dust baffling system to fill bags evenly. Supplied with & Includes: -- 25 HP motor with magnetic starter, -- (5) Upper cloth filter bags and (5) lower plastic collection bags. -- (5) Double "T: Bolt straps. -- (5) Quick release metal straps. -- Roll of 50 Lower Plastic Dust Collection Bags, 24" Dia. X 72" Long.Three Year Comprehensive Warranty