OverBuilt - Baler/LoggerOverBuilt Baler/Loggers are: The fastest, most efficient Baler/Loggers any scrap recycler can own.Compressing scrap metal & vehicles into denser, stackable forms results in more efficient loading &transport. Approx (5,500) hours.Specifications -- Charge box open: 20’ x 8’-5";. -- Closed: 240"; L x 40"; W x 26"; H. -- Bale Size: 40"; x 26"; x Variable. -- Min. variable distance: 22";. -- Bale density: 25 - 80 Lbs/ft³. -- Main compression cylinders: 2. -- Logging force (per side): 175 Tons. -- Charge box door cylinders: 6. -- Baling force (per door): 255 Tons.

OverBuilt - Baler/Logger: "NEW" in 2023OverBuilt Baler/Loggers are: The fastest, most efficient Baler/Loggers any scrap recycler can own.Compressing scrap metal & vehicles into denser, stackable forms results in more efficient loading &transport. Approx (4,000) hours.Specifications -- Charge box open: 20’ x 8’-5";. -- Closed: 240"; L x 40"; W x 26"; H. -- Bale Size: 40"; x 26"; x Variable. -- Min. variable distance: 22";. -- Bale density: 25 - 80 Lbs/CF. -- Main compression cylinders: 2. -- Logging force (per side): 175 Tons. -- Charge box door cylinders: 6. -- Baling force (per door): 255 Tons.

OverBuilt - Baler/Logger.OverBuilt Baler/Loggers are: The fastest, most efficient Baler/Loggers any scrap recycler can own. Machine does not have boom. Compressing scrap metal & vehicles into denser, stackable forms results in more efficient loading &transport. - Approx (1,500) hours.Specifications -- Charge box open: 20’ x 8’-5";. -- Closed: 240"; L x 40"; W x 26"; H. -- Bale Size: 40"; x 26"; x Variable. -- Min. variable distance: 22";. -- Bale density: 25 - 80 Lbs/CF. -- Main compression cylinders: 2. -- Logging force (per side): 175 Tons. -- Charge box door cylinders: 6. -- Baling force (per door): 255 Tons.

PANHANS - 436, ...24'' Single Surface Planer -- Specifications24.8" (630 mm) Width x 1/8" to 10" opening; 10 HP Motor; 4-knife - 4-3/4" dia. cutterhead belt driven @ 5,000 RPM; max. cutting depth: 5/16". -- 1 HP Feed motor with: (2) Feed speeds: 22 - 44 FPM. Segmented rubber-covered infeed and outfeed rollers, sectional chip breaker, motorized raise-and-lower of bed w/LED readout, table size 43" x 21". -- Options Include: (16) Cutter knives: Power lift up & down. -- Complete with: Emergency stop;, magnetic starter w/overload protection; knife setting gauge: & 5-1/2" dia. dust hood; includes: Operations manual; parts list; tool kit.

PAUL K34V/1000 RIP SYSTEM WITH (1) SHIFTING BLADE39.3" (1000 mm) max. cutting width x 4.1" (105 mm) max. thickness cap. -- Specifications: Bottom arbor design; (6) powered bottom and (6) powered top feed rolls propel lumber from the infeed system thru the Ripsaw.50 HP (37 kW) Main motor, 2,900 RPM driving a 2.362" (60 mm) dia. arbor with (1) moveable blade. Moveable saw has a shift-able range of 400mm.Moveable blade and fixed fence positions indicated by 15mw laser lights that project 16' lines down inbound boards. Arbor is removable on a slide system; -- Feed Works: 49 - 262 FPM (15 - 80 MPM) Variable feed speed feed drive; hydraulic drive to (3) sets of smooth top and corrugated bottom feed rolls before and (3) sets of smooth top and corrugated bottom feed rolls after the blades and individually controlled pressure to the feed rollers. With (3) sets of anti-kickback fingers. -- Equipped with: Automatic oiler, push-button station, upper dust hood and upper and lower dust chutes. In-feed roller table 980 mm with (7) rollers; universal type mounted to the machine. -- Operator Interface: 1 NCD control, VGA color monitor, features 10-width lists with 200 items (8 variable-width lists, 2 set-up lists for long bush fitted for fixed blades.) -- Machine is under power but not in production.

PEERLESS - Truck & Trailer Tipper & Receiving BinComplete with the following major components & features: -- Receiving Bin with Chain Bottom Discharge. (No transport conveyor after the bin.) -- 63° Tilt, 65 - 70 Ton cap., and 65 ft. Deck length. -- Twin hydraulic cylinders on each side. -- Dual hydraulic units. -- (2) Safety Bows.NOTES: This System seems to be in very nice condition despite being shut down for perhaps (10)years. Used at a paper mfg. facility. Has been dumping full trucks and trailers.

PEERLESS MONO 21 UNIT MATERIAL CHIP BINChip Bin main components: -- Bin with 21 Unit (4,200 cubic feet) capacity. -- Hydraulic power unit. -- Steel support structure. -- Clamshell-type material discharge doors. -- Price shown includes dismantling & loading onto trucks.

PELLET.TOWER Pellet Manufacturing System. -- Complete modular, vertically designed Pellet Manufacturing System within a 65' tall free-standing tower containing all the Pellet Manufacturing equipment necessary on a 17' x 20' concrete pad including all pellet producing material handling & conveyor systems. -- 25,000 - 30,000 Tons annual pellet capacity from wood or agricultural waste streams. -- Tower includes: (6) Levels, vertically integrated on top of each other; an operator monitoring station is located at the ground level, processing equipment is in the top (5) levels. -- Each level has direct "walk-up" service and maintenance access without personal lifts, ladders, or other access devices. -- Complete integration of electric power supply & panels, Compressed Air, Air Filters, and Dust Collection, with safety controls linked throughout the automated system. -- System designed to run and be maintained by (1) on-site operator or off-site with remote PC monitoring of the entire process. -- Each level includes high quality brand name equipment: Hammer Mill at the beginning of the process, Material Holding & Dosing Bin, as well as the Dust Collection & Air Handling system at the very top of the Tower. -- Binding Agent System, multiple Foreign Material Separators, Water Dosing with moisture control; Ripening Silo; high production Pellet Mill, Pellet Cooler, final Screening Station on levels below. -- Includes following auxiliary equipment: Process Control with full Visualization (on Monitors), Fire Protection, Explosion Prevention, Dust Collection, Spark Detection, Water Distribution, Compressed Air, and a Central Vacuum Cleaning System that makes all a clean enclosed work environment. -- The 6-levels are in a completely self-contained steel structure, enclosed with insulated sandwich panels and weatherproof cladding. -- Post-installation, in case of relocation, the Tower can be divided into (4) units for transportation on flatbed trailers; dismantling & reconstruction requires approx.(6) weeks. Pricing includes "delivery to site, installation & training". Please ask for full quote with all specifics - and geared toward your location, material, and application!

The PELLET.TOWER is a modular, vertically designed Pellet Manufacturing System providing an innovative, but proven solution to biomass pellet fuel production."Single Tower Series": -- Capacity: 2.8 - 6.6 tons/Hr (2.5 - 6.0 metric tons/Hr); -- Installed power: 415 - 750 HP (310 - 560 kW); -- Dimensioins: 17' x 20' x 69' (5 x 6 x 21 m); -- Weight: 79 - 90 tons (72 - 82 metric tons)."Dual Tower Series": -- Capacity: 6.6 - 11.0 tons/Hr (6.0 - 10.0 metric tons/Hr); -- Installed power: 945 - 1,275 HP (705 - 950 kW); -- Dimensions: 32' x 18' x 75' (10 x 5.5 x 23 m); -- Weight: 157 - 165 tons (142 - 150 metric tons)."Triple Tower Series": -- Capacity: 10 - 15 Tons/Hr. (9.0 - 13.6 metric tons/Hr); -- Installed power: 1,542 – 1,823 HP (1,150 – 1,360 kW); -- Dimensions: 67.25' x 26.9' x 75.13' (20.5 x8.2 x 22.9 m); -- Weight: 232 - 243 tons (210 -220 metric tons).System Highlights: -- Over 100.000 Hrs operating experience. -- Modular system to produce high quality pellets; -- Standardizes components; -- Compact design (small footprint); -- No building required ("single machine"); -- Semi-mobile system (relocation possible).Main Components: -- Feeding bin; -- Binding agend adding; -- Foreign material separator; -- Hammermill; -- Air/material separator; -- Conditioning bin(s); -- Pellet mill(s); -- Central lubricator; -- Pellet cooler(s); -- Pellet screen(s); -- Exhaust air filter; -- Compressed air; -- Fire/spark detection & extinguishing; -- Central vacuum cleaning system; -- PLC control & visualization.

PENDU - 3800, ...Stake PointerPENDU's "High-Speed Stake Pointer" is designed for: High volume production of surveying & agricultural pencil point stakes.Includes: Hopper fed material size range from: 3/4" - 2 1/2"; square or rectangular material: 16" - 72" In length. -- Equipped with: Aluminum housing round cutterhead with: Replaceable knives; powered by a 10 HP - 3,600 RPM motor; shaving the end of the stakes to a pencil point. -- Automatic feed via: 3 HP Variable speed electric drive; outfeed for pointed stakes on: (6) Arm staging station; pneumatic clamping: Secures part during cutting. -- Complete with: Fabricated steel construction; chip shield with dust shroud for chip extraction; prewired Operator Control Console.Unit is capable of producing up to: (2,700) Stakes/Hr.

PETERSON PACIFIC 5000G Whole Tree ChipperSpecifications: -- Engine: CAT 3412E 1000 HP Diesel Engine -- 3-Flail, Key Knife system currently set for 5/8 chip sizeRecent rebuild on machine: -- Overhung load adapters both replaced within 1000 hrs -- Fan pump replaced within 1500 hrs -- Swing/ boom pump replaced within 750 hrs -- Stick boom pump replaced within 100 hrs -- Engine computer less than 750 hours -- High pressure fuel pump less than 750 hours -- New radiator last summer -- Update main boom pump & flow divider last fall -- Installed a new seat 2 years ago -- New muffler -- New auxiliary bark pusher pumpEquipped with: -- Spare flail pump -- Spare flail motor -- New feed roll teeth -- Spare belts -- Spare pins -- Seal kits -- Spare clutch

PHI IR-3 Preheater;Overall dimensions 5' wide x 4' long, consisting of: (3) IR Medium Wave heating banks, each 1" wide x 54" long, bank has gold foil quartz heating elements.This IR unit is designed to preheat the board to facilitate out gassing and help eliminate solvent pop and air bubbles in the coatings of deep pored materials such as oak. Also used to standardize board temps during colder months as well as decrease dry times of other substrates. These units are primarily (but not exclusively) designed for use before the application of stain and sealer coats. Features: Explosion proof electrics, electrical heat temperature adjustable from 100° - 150° F, variable feed speed from 8 - 30 FPM (2.5 - 9 MPM).

PHL Edger high speed 4 saw edger; Complete with the following features: --Independently shifted blades. --48″ opening. --2-3/4″ max cut depth. --125 HP Arbor Motor. --Operates up to 800 linear feet per minute. --Infeed Table and Outfeed Table with Picker and Hydraulic Power Unit. NOTE: Removed from service November 2015. Set up for transverse scanning. No scanner included.

PILLAR MACHINE HPLD 96" CNC BORE & LOCK-DOWEL INSERTER: -- Specifications:(4) Working zones of 24" each and "OPTIONAL" working table length of 96"; CNC controlled head assembly with rapid (side-to-side) traverse.Head assembly with: (1) Horizontal boring & insertion unit with a 3 HP - 18,000 RPM Direct-Drive Spindle motor; "X" Axis is servo controlled for positioning; Digital Mechanical Readouts for Height and DepthHead is currently set up to bore/machine/insert 20 mm Lock-Dowel "Eclips", H-clips, Channel Locks & 8 mm Spring Pin Fasteners.Material thickness capacity 0.5" - 1" max. Material thickness with digital readout for height adjustment. -- Clamping System:(8) Pneumatic, quick side-to-side adjustable hold-down clamps for horizontal "Lock-Dowel" processing on the panel edge.(1) Pneumatic Clamping Bar for vertical boring into the panel face/back. -- Operator Interface:15" Color Touchscreen control + Windows 10 Operating System. Ethernet 1 x PCIE Broadcom GbE (or similar), USB: 2 x USB 2.0 (or similar), Serial Port: 1 x RS-232 (or similar)The on-screen graphics of the operator interface have been designed to allow for quick programming at the machine. Typically, programs can be written and recalled in less than one minute.The Interface is open architecture allowing it to integrate with design software that can give hole locations in the form of a .xml file or a bar code (with bar code reader purchase found in options).Standard Features in the software include: 1. Graphic interface to show where holes are to be drilled and if a dowel is to be inserted. 2. Pattern Drilling/Inserting.3. Password protection of certain features/functions. 4. Online diagnostic capability (if machine is connected to an internet connection). 5. Toggle between Metric or Imperial programing parameters. -- Features: This machine will insert H-clips, Channel Locks and Spring Pins with ease. Using CNC control, this machine positions the drilling spindle to bore holes and insert the Lock dowel hardware. -- Complete with:Anti slip table surface, rack & pinion drive, and centralized dust collection manifold. -- Actual model is: PILLAR MACHINE HPLD

PILLAR - H49: CNC Bore, Glue & Dowel Inserter -- Specifications(2) Working zones and overall, 49" max. width capacity.(1) CNC Controlled head assembly with: Rapid (side-to-side) traverse; assembly with boring, gluing & insertion unit; 1 HP - 18,000 RPM drill motor.(4) Vertical pneumatic hold down clamps; function selector control for boring only or doweling, adjustable drilling speed.1-9/16" (40 mm) Max. dowel length; setup for 8 mm dowel dia.; height adjustment up to 1-1/8" material thickness with digital readout. -- Operator InterfaceCNC "Color Touchscreen" Controller for: Function & part programming and program storage. -- Complete with:(1) 12" Dia. vibratory feed hopper: Totally sealed electronically metered glue system with 1-button flushing.100 PSI High power glue pump; 2-1/2-gal. glue tank; anti-slip table surface; 49" X-axis cap.Rack & pinion drive; centralized dust collection manifold.

PINHEIRO PMC 4-450 Four Sided PlanerSpecifications: -- 18" x 6" Max. cap. motorized opening, -- Top head 18 HP, -- Bottom head 12 HP motor, -- Both side head motors are 9 HP; -- All spindles 40 mm dia.; -- Digital readouts on top and outboard left spindles, 5" max. tool dia. -- Max. profile depth of side heads 1" max. -- 5 HP Feed motor, (6) feed speeds between 10 & 75 FPM, (To be confirmed) -- (4) powered feed rolls, sectional feed rolls, sectional chipbreaker, central lubrication system. Includes: -- Sound hood, Star Delta motor starters,

PMK C 1205 Single End Coping Machine -- With the C-1205 Coping Machine you can run your Styles first or run your cope first, this machine using a 7.5 HP motor has counter rotating spindles to insure Chip free coping of either square. -- Single profiled or double profiled parts. Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 13.5" wide on the C-1205. -- Two counter-rotating spindles 1.25" in Diameter. -- Capacity of maximum (2) cutters on stack tooling -- Spindle Speed 7,000 RPM; cycle time approx. (4) Seconds. -- Side Pressure Clamp to insure proper alignment with a fence. -- Cutter Heads totally enclosed for Safety!

PMK C 1203 Single End Coping/Tenoning Machine -- With the C-1203 Coping Machine you can run stiles first or cope first, this machine using a 5 HP motor has counter rotating spindles to insure chip free coping of either square, single profiled or double profiled parts. -- Since we are only coping one end at a time the length doesn't matter. We can also cope more than one part at a time up to 9.5" wide on the C-1203. -- (2) Counter rotating spindles 1.25" diameter. -- Spindle Speed 7,000 RPM; cycle time approx. (4) seconds. -- Side Pressure Clamp to insure proper alignment with fence. -- Cutter Heads totally enclosed for Safety!

PNEUMAFIL 13.5-460-8 Reverse Air Dust Collector System;Reverse Air Dust Collector with 42,600CFM at 9 to 1 air cloth ratio, 4,738 square feet of filter area. -- 13-1/2' Dia. round baghouse contains (460) bags - 96" long by 5" dia. filter bags in galvanized cages w/reverse jet bag cleaning. -- Reverse Air from 15 HP blower motor which cycles once a minute over filter bags (rotating plenum covers each row of bags once a minute, reversing the normal air flow direction. -- Reverse Air action back flushes the bags and dislodges wood dust particles collected on the filter media which then fall to the bottom of the 60° funnel hopper for removal), bags are changed via walk-in door.. -- Material handling fan with approx. 48" inlet dia with 150 HP floor mounted motor (covered in a shed); 0.25 HP explosion proof motor for manifold drive. -- Rotary Air Lock, gearmotor driven at the bottom of the hopper feeding and shared horizontal screw type auger (if you want it) with gearmotor drive. -- Features: MOTOTRONICS Soft Start for main motor. FIRETEK Spark Detection System (subject to prior sale with adjacent unit). -- Includes: Explosion doors, sprinkler pipe, interior electrical control panel, support frame, safety ladder, railings, and exterior ductwork.Professional dismantling, rigging, transport and installation is available.NOTE: Unit being sold under this record is pictured on the left side on the first two photos. For the smaller diameter unit on the right side (DIXIE AIR) see record "DO-011266".

POWERMATIC PF-41 4-Roll Power FeederFeatures: -- Cast Iron construction. -- Continuous duty motors transfer power from the gearbox to the feed rollers. -- Moveable universal joints and locking mechanisms lock the feeder in horizontal, vertical, or angle feed positions. -- Roller chain and sprocket design provide positive feeding for all types of materials. -- Rollers can be changed out easily and quickly; Smart roller system allows for the tires to be replaces without replacing the assembly. -- Solid cast iron construction of body pieces and base. -- The support column is fully adjustable for horizontal, vertical or angled feeder position. -- Universal joints provide stability for vibration-free feedingSpecifications: -- Swing 360°. -- Motor Power 1 HP. -- (4) Feed speed rates at 13 / 36 / 43 / 108. -- Max. Height of Rollers Parallel to Tabletop 8-1/2".