EXTREMA DC-240.1 TYPHOON Fabric Filtration Dust Collection System. -- Powerful, portable, and affordable dust collector with roll around casters mounted to a steel platform base. -- (2) Oversized Fabric filter top bags, approx. 75 sq. ft.filter area, are placed above plastic collection bags, approx. 18.85 cu. ft. storage capacity. -- 3,950 CFM Output with single-stage blower. -- 5 HP Induction motor. -- Filter bags filter dust particles down to (5) Micron in size. -- Main inlet 10" or dual 4" adapter.

EXTREMA DCF-327 Baghouse Dust Collector.Features a 16" inlet; unit has (3) sections with (9) socks per section. -- Filter Socks: 6" Dia. x 70-7/8" for greater air-to-filter ratio; (1) Micron filter. -- For indoor use. (Enclosed outdoor unit available). -- Excellent addition to the "DCY Typhoon" Dust Collector

EXTREMA EXCESS XS-1E37 SINGLE HEAD WIDE BELT SANDER37" Width capacity, 0" to 6" conveyor bed opening. Mono-block construction for solid, vibration free operation and increased durability. -- Equipped with: Combination sanding head with rubber covered contact roll & graphite covered platen. -- Over thickness material feeding safety device. -- Digital material thickness controller setting with LED readout accurate to a thousandths of an inch. -- "Automatic Thickness Setting" device for easy setup. -- OMRON Electronic abrasive belt tracking. -- GOODYEAR Endless conveyor belt with automatic belt tracking. -- 20 HP Main motor. -- REGAL Variable feed speed drive unit; 2 HP motor. -- 1/2 HP Power elevation motor. -- Large cabinet style doors for easy service access. -- Pneumatic abrasive belt tensioning. -- Double infeed & outfeed covered holddown rollers. -- Infeed conveyor extension with safety stop bar, emergency stop button and motor load meter.

EXTREMA XR-12LE STRAIGHT LINE RIP SAWCompact Straight-Line Rip Saw with a guaranteed 8' glue line. -- Powered by a 15 HP direct drive motor. -- Equipped with: a Wye-Delta soft start for lower amp requirements during start-up. -- Heat treated chain and raceway with automatic oiler. -- All SQUARE D electrical controls. -- Large 14-3/4" rip capacity. -- Overarm control box mounted on the in-feed side. -- Total space requirements are about the same as a standard size table saw.

EXTREMA - XP-126A: Planer with Helical Head26" x 11-3/4" Cap.; 5/16" max. material removal; 10-1/2" min. part length; 20 HP WESTINGHOUSE / TIKO belt driven motor; STEALTH helical carbide insert cutterhead: 6,000 RPM; variable speed feed: 20 - 75 FPM. -- Equipped with: Powered raise-and-lower of 27" x 35-1/2" table; digital thickness controller; sectional chipbreakers; sectional infeed roller & dual outfeed rollers; (2) adjustable bed rollers.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EXTREMA - DCY-1425 L3 TYPHOON: Cyclone Filtration Dust Collection System. -- Powerful 2-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system before passing finer particles through the fan & filter. -- Free air volume: Rated @ 10,500 CFM. Low noise operation. Equipped with: -- 25 HP Motor with a Soft Start already wired in. -- Rotary air lock with: 1 HP Motor @ 38 CFM. -- Standard support frame: LEG 3 164" clear height x 149" clear width x 91" clear depth. -- (2) DCF-327E Exterior baghouses for more than enough filtering capacity.

EZ CAR - (Used) Model A: Car Crusher Approx: 6,200 hours.New in: 1988.System Pressure: 2,500 PSI.Port Reliefs set at: 2,650 PSI.Cylinders: 10" Bore.Travel: 78".Shaft: 4" rod.OpeningSize: 20" x 8'-1" x 7'-7".OverallWeight: 61,000 Lbs.Length: 43'-1/4."Travel & operating height: 13'-1/4'.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured.

FCM 30HP Vertical Feed Hammer HogSpecifications:- Intake 14" X 18" -- Drive motor 30 HP -- Extraction 8" diameter -- Screen with 3/4" holes -- Magnetic starter

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER FORMAT4 PROFIL 45, ...2" 12 HP Interchangeable Tilting Spindle Sliding Table Shaper, with Power FeederAllows Operator to store up to (99) programs of spindle heights & angles.Specifications: -- 12 HP Motor operates on 230 Volt / 3-Phase power. -- Motorized rise & tilt of spindle: Tilts back 45° & forward 5°. -- Motorized fence w/digital readout. -- Sliding Table with clamp. -- STEFF 3-Wheel Power Feeder w/WESTERN ROLLER soft wheels. -- AIGNER Integral fence and AIGNER CENTREX guard. -- Articulated arm to move Power Feed out of the way for large curved work. -- The fence is hinged, so it can be folded below the table, out of the way for doing large pattern work, as well.NOTE: Spindle does not currently function.

FELDER FORMAT4 PROFIT H08 FLAT TABLE MACHINE (W/LOADING, UNLOADING): -- Specifications5' x 10' "MATRIX" Phenolic Flat Table design for: "Nested Base" Manufacturing. -- Working Capacity"X" Axis is 121.6" (3,090 mm); "Y" axis is 60.2" (1,530 mm);"Z" axis stroke is 11.8" (300 mm); max. material thickness is 4.3" (110 mm). -- Positioning Speed"X" & "Y" Axis at 197 FPM (60 MPM); "Z" axis is 49 FPM (15 MPM). -- WorktableThe working area is subdivided into (8) vacuum fields (H08 16.31) to ensure the best holding force for the most varied board sizes.The vacuum fields are controlled manually by means of: Hand levers on the front side of the machine. Prepared for (optional) elevated pods: Allows profile & horizontal machining. -- Boring Unit(1) DH 8-Spindle Vertical Drill block on 32 mm centers. -- Machining(1) 13.4 HP (10 kW) Vertically mounted electrospindle Router with: HSK F63 Adaptor; inverter driven 1,000 - 24,000 RPM; max. torque from 12,000 RPM.(1) 15-Position ATC Tool Rack: Mounted at the end of the machine. -- Operator & Machine ControlPC Based user-friendly; icon driven control housed on the: Main machine base + "WOODFLASH" Operating System. -- Complete with:(2) 250 cbm/Hr Vacuum pumps; handheld terminal with: Potentiometer & emergency stop; automatic measuring system of the tool length.Sound absorbing protective head enclosure with: Debris curtain around bottom edge. -- Options Include: Automatic unloading unit with: Electromotive offloading pusher. This addition allows finished workpieces to be automatically pushed off the table after processing: Reducing manual handling & speeding up production cycles. -- Actual model: FELDER FORMAT4 - PROFIT H08 16.31

FELDER FORMAT4 PROFIT H08 16.31 FLAT TABLE MACHINE (W/ATC) -- Specifications5' x 10' "MATRIX" Phenolic Flat Table design for "Nested Base" Manufacturing. -- Working Capacity"X" Axis is 121.6" (3,090 mm); "Y" axis is 60.2" (1,530 mm);"Z" axis stroke is 11.8" (300 mm); max. material thickness is 4.3" (110 mm). -- Positioning Speed"X" & "Y" Axis at 197 FPM (60 MPM); "Z" axis is 49 FPM (15 MPM). -- WorktableThe working area is subdivided into (8) vacuum fields (H08 16.31) to ensure the best holding force for the most varied board sizes. The vacuum fields are controlled manually by means of hand levers on the front side of the machine.Prepared for (optional) elevated pods that allow profile & horizontal machining. -- Machining(1) 13.4 HP (10 kW) Vertically mounted electro-spindle router with: HSK F63 Adaptor; inverter driven 1,000 - 24,000 RPM with max. torque from 12,000 RPM.(1) 11-Position ATC tool rack mounted at the end of the machine. -- Operator & Machine ControlPC Based User-Friendly, icon driven control housed on the main machine base + "WOODFLASH" Operating System. -- Complete with:(1) 250 cbm/Hr Vacuum pumps; handheld terminal with: Potentiometer & emergency stop; automatic measuring system of the tool length.Sound absorbing protective head enclosure with debris curtain around bottom edge. -- Actual model: FELDER FORMAT4 - PROFIT H08 16.31

FELDER FORMAT4 - Profit H08: Flat Table Machine Specifications -- 4’ x 8‘ Flat Table Working Capacity: X: 2,500 mm (98.4";); Y: 1,250 mm (49.2";); Z: 85 mm (3.3";).Gantry Outrigger: (2) synchronized Servo drivers in the X-direction; max. speed rate: 25 MPM (985 IPM). -- (1) Servo Driver: Y-Direction; max. 25 MPM (985 IPM); (1) Servo driver: Z-Direction max.; 15 MPM (590 IPM); power transmission in X. -- Y Via rack & pinion ball bearing spindle on: Z Axis; axis runs on ground linear guides. -- Automatic Centralized Lubrication of all axes -- Nesting Table: (2) Stops in X-direction: (1) Stop in Y-direction, left rear side; (6) manual switches situated in front of the machine; heavy valve system. -- Phenolic Vacuum Table with: (6) Vacuum fields and manual field choice. -- Stop cylinder at: Rear left; (2) in X, (1) in Y direction; electric box front left with light barrier. -- 1 ST 305-01004. -- Configuration package "Professional" H08 13.25 10 kW (S6) main spindle: HSK F63 Left/right rotation; 1,000 - 24,000 RPM controlled by inverter. -- Drilling Head "DH8": (8) Vertical drills; 1,000 - 6,000 RPM; controlled by inverter; 8-position tool changer. Extraction Hood: (22) Separate connections -- Software: Compact; standard PC with Windows 7 Controller; control for the use of ISO-Code; WOODFLASH programs on the machine.Includes: 210 cbm/Hr BECKER Vacuum Pump.

FELDER - G-330: Edgebander0.4 - 3 mm Edge thickness cap.; 40 mm panel thickness; 3" min. width; 4-3/4" min. panel length.Equipped with: -- Quickmelt TEFLON coated glue pot for granular hot-melt adhesive. -- Heavy-Duty Guillotine: Up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations -- Single motor; Double Blade End Trim with: HF Motor; 12,000 RPM. -- Top & Bottom Flush/Bevel Trim: Bevels 0° - 15°; 1/2 HP motor - 12,000 RPM each. -- Open space at outfeed. -- Single feed speed: 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations; outrigger panel support; used tooling.NOTE: Seller states that the equipment has less than (500) hours of use!

FESTO - DSS3: Push Feed MoulderSpecifications -- 4-Head. -- 3-1/4" x 2" Max. cap.; 3/32" x 3/16" min. cap.; 10" min. length. -- Equipped with: (2) Side heads; 7 HP - 9,500 RPM motor; top & bottom heads: 3 HP - 8,500 RPM motor each; 3/4" dia. spindle. -- 4-Feed rollers steel & urethane. -- Top head: Tilts both directions.

FIN - ST 1600, ...Top/Bottom Cleaning Brush.62" Width and 3-1/8" max. thickness opening, thickness adjustment by handwheel via worm gear with dial indicator.Equipped with: -- Top & Bottom nylon brushes driven by 3 HP drive motor (only 1-brush with machine). -- Separate variable speed feed motor with magnetic controls driving 3" dia. rubberized infeed & outfeed pinch rolls. -- Full fabricated sheet metal enclosure for efficient dust collection, dust enclosure hood with central 6" dia. dust outlet connection.