CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

Extremely well-built Edge Sander with 5 HP - 1,200 RPM TEFC Motor. -- (2) 11" x 60" Cast iron platens. -- 10" x 172" Abrasive belt size. -- 0.5 HP oscillation motor to produce (150) oscillations/Min with 1/2" movement. -- (2) 11-1/2" x 62" Cast iron side tables and (1) cast iron end table. -- All tables with 30° tilt up & 45° down. -- 5" Vertical table travel, 5" lateral side table travel and 4-1/2" lateral end table travel. -- Convenient hand wheel adjustment. -- Large 10" dia. x 10-1/2" face direct drive pulley with 4-1/2" dia. x 10-1/2" idle pulley for a huge sanding surface. -- Magnetic controls with overload protection & dust hood with 4" dia. outlet.

CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

CHEN SAN FUNG SD-100 Denibbing Sander --39" Width cap.; (1) head with (6) 0.5 HP counter rotating arbors mounted on a central rotating drive assembly with (20) blades per spindle, variable assembly rotation from 2 - 20 RPM. -- Each arbor/spindle is equipped with abrasive fladder disc type brush media, variable arbor speed from 300 - 1,200 RPM. -- Conveyor belt feed with vacuum holdown, variable feed speed from 6 to 39 FPM with 2 HP drive. -- Infeed & outfeed holddown pinch rolls, 0" to 4" motorized part thickness with working width from 6" to 39" part size opening with mechanical readout. -- Complete with: Controls on belt loading side, RPM readouts for spindle speed, magnetic starters, 7" dust collection outlet and optional 15 HP vacuum turbine motor.

--In Auction: https://exfactoryauctions.com/Detail/SA-231009/event/A122024$1 --No RESERVE!-- CHIA LUNG KR-30 2-Spindle Dual Table Automatic Rotary Copy Shaper Equipped with: (2) 19” Dia. x 35-1/2” H Tables. (2) 6-1/4” Dia. Center clamp plates.

CK POWER CKT375VM-T4 DIESEL GeneratorSpecifications: -- Engine: Volvo Penta TAD1372 Tier 4 Final EPA/ CARB Certified -- Ratings Range: 60HZ (3 phase / .8 power factor) -- Prime: 275 kW / 343 kVA Standby: 300 kW / 375 kVA -- Standard configuration: multi-voltage selector switch, 120/240V 1 Phase, 120/208V 3 Phase and 277/480V 3 Phase -- Fuel tank: 300 gallon, 17 Hour run time @ 100% load -- Hours: less than 500Equipped with: -- CK/Deep Sea custom controls -- Easy to use custom configuration -- All components are UL1446 certified -- Fork pockets and transportation tie downs -- Lockable storage -- Level 1 sound attenuation: 70 dBA @ 23 ft. -- Standard 20 amp 120 volt convenience receptacle

CML NEW FINISHING TOWER/6 Multi Level Oven System: This type of oven is very flexible thanks to the FIFO (First In / First Out) operation and the possibility to adjust the stay time using more or less belt trays.It is particularly suitable to help the evaporation of the volatile components contained in UV curable paints, or to carry out a first degree of drying of conventional paints in an 'out of dust' environment. - Its technical characteristics also make this system extremely suitable for drying or curing materialDescription of the Standard Equipment & Specifications: -- Overall dimensions: 7,650 x 3,300 mm x 3,250 mm height (25’ x 11’ x 10.67’ H). -- Weight: 4.000 kG (8,819 Lbs)Multiple Floors Dryer, mod. TOWER/6 Paint Coated parts (panels components) are transported on (6) belt conveyor trays, moving vertically up/down, having a length of 6,500 mm (256") each. This practical length makes it possible to load "two panels charges" having a length of 3,000 mm. (9.85 feet) each. -- Max. weight supported by every belt tray level: 115 kG (253.5 Lbs). -- Max. allowed thickness 50 mm (1.97 inches) -- Speed controlled by inverter at belt travel steps of 3.250 mm (127.9") or in continuous model. -- Vertical movement on (4) pre-tensioned chains controlled by motor with gearbox. -- Cabinet made of structural carbon steel profiles and pre-painted insulated panels, complete with entry door and windows. -- Ventilation by means of laminar air distribution among the floors. Average air speed 2 m/Sec (6.56 feet/Sec) - (100% of the air volume is taken from the outside and exhausted to the outside). -- Air supply unit complete with centrifugal fan taking the air from the outside of the building, complete with heat exchanger to be supplied with hot water, with temperature adjustment system and double set of pocket filters. -- Air ductworks between air supply and exhaust fans and distribution boxes (plenum) is included. -- Ready to be connected to emergency system to stop the line -- Curing Tunnel operating functions controlled by SCHNEIDER PLC via electronic keypad input. -- Separate electrical cabinet in IP 55 execution - IP 55 motors -- Manufactured according to CE Standards and covered by a (12) Months or 2,000 Operating Hours Warranty for defective parts or materialOther Dims, Operation & Utilities: -- Dimensions of the electrical switchboard: 800 x 600 x 2,000 mm (2.7’ x 1,97’ x 6,56’) -- Total power: kW 10,5 -- Compressed air:: lt/Min 20 (5.29 gal/Min) -- Exhausted air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Supply air volume: m³/Hr 7.500 (264,860 feet³/Hr) -- Thermal power: Kcal/h 125.000 (326,000 BTU/Hr), - AIR In/Out: 50°C (122°F)

DUSTEK W-2500 Whispurr 5-Bag Dust Collector.Specification: 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Magnetic starter.

DUSTEK M750 Interior Filter Bag Dust Collector7.5 HP Motor, compact 3-bag free standing & self-contained heavy-duty dust collector. -- Rated @ 3,450 CFM, 9" - 11" static pressure at fan. -- Equipped with: 12" Inlet dia., (3) upper filter bags with 99 sq. ft. filter area . -- Dynamically balanced aluminum impeller with easy access; 45 Cu. ft. collection cap., dust is collected in 6-mil thick clear plastic for easy disposal, a unique adjustable baffling system assures even filling of bags.

DUST-EX AG22 Abort Gate/Valve.... Automated two-way air stream diverter valve which prevents fires and explosions in dust collection systems and reduces the risk of fire in explosive prone work environments. A "safety measure essential" when clean air is returned to a building. -- Consists of: A lever arm that automatically directs a flapper damper in two different directions. -- Normal Position: The damper stays in a horizontal position (open) allowing the air stream to be directed/returned to the building -- Abort Mode: In the event of a spark originating upstream of an outside dust collector, a Spark Detection Sensor positioned in the air stream inside the building, sends a signal to de-energize an electro-magnetically controlled latch.The flap of the valve is very quickly switched to the abort/second position (closed) thereby diverting the explosion pressure/air stream to the atmosphere. Thus the inside work environment is protected from the explosion. -- Reset Mode: A pneumatically operated system is added to reset the damper position. -- Comes With: NEMA enclosure, 10" x 10" x 6". Enclosure for Pneumatics 22" x 22" -- All (3) flanged connections are 22" x 22'" square. -- Construction: Damper assembly is fully bolted to provide solid, reliable operation. -- The power adapter for the independent power supply is extra.Overall dimensions: 60" long x 36" wide x 43" high.Improve the safety of your work environment & help comply with NFPA codes!

DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

DUST-EX HSAG-24 Packaged Safety Solution for a 23"x23" (24" dia. round equivalent. Suitable for up to 25" dia. ) Return Air Rated for max 12,850 CFM @ 3,500 FPM.. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Heavy Duty Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel, Intrinsically Safe, CP05 - single zone, allows for installation of (1) inlet and (1) outlet explosion isolation valve(s), (3) monitored inputs per zone (two programmable), (1) intrinsic circuit with barrier and physical separation (one per zone), outputs for system shut down and monitoring, NEMA 4 enclosure, 120 VAC or 24 VDC. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 40" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK-02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) Heavy Duty High Speed Abort Gate, RGAG-23, magnetic , 23" x 23" flanged inlet and outlet (24" round equivalent), suitable for 21" - 25" dia., control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 12,850 CFM @ 3,500 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe (broken bag detector) RS-PDP03, RS-MK02DP, etc. IP 65 encl

EARTH CARE PRODUCTS, INC. 10½ Ft. x 32 Ft. Triple-pass Rotary Drum Dryer System with Gas Burner;Complete with the following major components: -- 10.5 Ft. x 32 Ft. (despite the model DB-1030) Triple-pass Insulated drum. -- Trunnion Bases, and 30 HP Drum Drive. -- High efficiency Cyclone, Cyclone outlet Airlock. -- 100 HP Dryer Main Fan, and Ducting. -- 25 MM BTU Gas Burner complete with Refractory Lined Furnace and Gas Train. Notes: &#9679 The Trunnion Tracks and Trunnion Wheels are in good condition as is the drum interior. The system was renovated in 2015 and not used much after the work was done. &#9679 The equipment is still in-place.

EKSTROM / CARLSON - 18, ...Pump Sander Pump Sander with: (2) 1" Dia. horizontal spindle; 2 HP - 1,200 RPM enclosed motor; mounted on heavy cast iron pedestal. -- Complete with: Push button magnetic controls & starter; 4" dust collection port.

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 4-1/2"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 250 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition. -- 3 extra blades

EKSTROM CARLSON - Model EE, ...Straight Line Rip SawSpecifications: -- 30 HP Saw arbor motor. -- Max. thickness 3-1/4"; with 16"; dia. saw blade (no blade). -- 5 HP Feed Motor with feed rates infinitely variable to 280 FPM. -- (3) Lower infeed rollers are chain driven and are adjustable from 0° - 5°. -- Elongated pressure bar housing assures the proper guidance across the entire table length.Equipped with & Features: -- Spring-loaded rollers with 1 in. yield. -- Dual position and lubrication system; (2) outfeed rollers. -- Please note: Chain appears to be in very good condition.

ELGI EG75-125 Rotary Screw Air Compressor; 100 HP - 453 CFM @ 125 PSIG100 HP Rotary Screw Compressor, 450 CFM @ 125 PSIG(Direct Drive); Air-End equipped with "eta-V" profile rotors. -- Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty: Lifetime warranty subject to adherence to conditions outlined below. The scope of lifetime warranty will cover replacement of parts and free of cost labor for 120 months from date of start-up or 126 months from date of shipment from an ELGi warehouse, whichever occurs first. Parts only thereafter.Optional: [F10501 / CRP-500] Clean Resources F10501 / CRP-500 CRP-500 CFM Oil/Water Separator System (Includes DC Plus Manifold Installed) Order Number: 553-12-0047 The Next Generation Molecular Filtration System Compression-fit manifold for precise filtration control Timer drain for improved flow of condensate through the media bed Antimicrobial sanitation of discharge hose to prevent algae growth Twelve available inlets (increased from six) No maintenance or messy bag change-outs Cradle-to-grave warranty System monitoring services - Add ...$ 2,650

ELGI EN11-125 Tank Mounted Rotary Screw Compressor w/Refrigerated Dryer, 15 HP - 55 CFM @ 125 PSIGENCAP Series Screw Compressors:120 Gallon Tank Mounted with refrigerated dryer and filters - are designed to encapsulate all functional components and compressor within a common housing. With its small footprint, high reliability and low maintenance requirements, the compressors are ideal for all industrial applications where size, efficiency and cost matter.Equipped with & Features: -- 6 Year Airend Warranty -- Low Sound Enclosure -- Premium Efficiency NEMA motor w/F insulation -- TEFC Drive and Fan Motor -- High Ambient Oil Cooler for low operating temperature -- UL/cUL Certified Control Panel -- Controls & Indications: Microprocessor Controller includes -- Maintenance Schedules -- Pressure Transmitter -- Temperature Transmitter -- Auto Restart -- Remote Start / Stop -- Modulation and Load / Unload Controls -- Phase Monitor -- DCS Connection through Rtu/RS 485 PortRecommended option: F10105 / MICRO 100 Clean Resources F10105 / Micro 100 Clean Resources F10105 Oil/Water Condensate Separator - add $ 775

ELGI EGRD 500 Refrigerated Air Dryer (480 CFM)The ELGi EGRD 500 refrigerated dryer is designed to provide a constant 41ºF dew point and utilizes the latest advancements in refrigeration technology to provide low operating cost and years of trouble-free performance.The advanced “ALU Dry"; aluminum heat exchanger module enables the packaging of the pre-cooler, evaporator, separator, and reheater all in one compact unit. This reduces the size, weight and pressure drop associated with conventional exchangers and optimizes the overall performance and reliability of the dryer which ensures effective removal of condensed liquids regardless of flow.Features: -- Microprocessor Controls with Dew Point Display Indication -- All-In-One Aluminum Design Exchanger -- Low-Pressure Drop -- Ozone Friendly Refrigerant -- De-Mister Type Moisture Separator -- Environmentally Friendly Refrigerant -- Hot Gas Bypass for Constant Dew Point -- Extended Service Life -- Timer Drain Options Include: ELGI Pre-filter AF 0520P rated at 520 SCFM, 1-1/2" NPTPremium Filter Series is constructed from premium materials and features with ease of installation and service in mind. Filter elements have a unique push-fit, double O-ring design to ensure no contaminants get down stream. Features: -- High Quality Aluminum Construction -- Automatic Internal Float Drain -- Pop-up Filter Change Indicator

ELGI EN07-125 10 HP ENCAP Rotary Screw Compressor w/Tank & Dryer; 38 CFM @ 125 PSIG.ELGI's 10 HP Rotary Screw Air Compressor w/20 CFM Refrigerated Dryer mounted on a 120 gal. receiver tank. -- Equipped with: 10 HP motor operation up to 115°F ambient temperature; "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely. -- Includes: 120 Gal. receiver tank, 40 CFM Refrigerated Air Dryer; single-door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: -- [F10104 / MICRO 50] Clean Resources F10104 / Micro 50, Clean Resources F10104 Oil/Water Condensate Separator - Add $ 305Designed for smaller compressed air systems. This system was designed as an economical solution for small compressed air systems, up to 125 psi. Theproduct offerings also include a factory-installed and plumbed wall bracket, reducing installation time. Replacement cartridges provide easy, no messmaintenance and offer the lowest life cycle cost in the industry.