COE 249D Veneer Lathe with the following: -- 27" maximum log diameter, Approx.110" knife length. -- 1484 Veneer Lathe Big Bar. -- 1390 Veneer Lathe Core drive. -- 3 to 1 inner drive ratio. -- Capable of peeling approx. 35 cubic meters per hour. -- Includes: • Linden step feeder• Small log offset x-y spindle chucks• 27"; maximum log diameter• 1484 big bar• 3 to 1 inner drive ratio• Digital ball feed carriage drive -- Note: Sold without 'charger or drive' included. -- This COE Veneer lathe line was completely rebuilt and installed in 2006. The lathe was operated less than one year and is reportedly in very good condition.

144L X 120"D X 144"H (25) Filter Screens (4) 12" X 48", (4) 4-tube light panels(1) Exhaust Fan 1HP 120V

COMEC - LON-LS, ...Horizontal Belt SanderSpecial design for sanding of straight or curved solid wood parts such as: Chair legs, chair backs and other similar & difficult-to-sand parts.10 HP Belt driven motor; 12" dia. contact drum for 10" wide x approx. 140" long abrasive belt; air tracking & belt tensioning. -- Stock is fed over the contact drum with an overhead variable speed, pneumatically tensioned feed wheel. -- Sander belt power: 6.6 kW (9 HP approx.) - 220/440 V, 60-Cy, 3-Ph motor.

COMEC - FAS/2, ...Corner Milling MachineCOMEC FAS is a dedicated milling machine with: Inclinable heads for machining the corner of chair seats. Specifications: -- (2) Heads with: 5.5 HP motor and 40 mm spindle shaft. -- Max. cutter size: 150 mm (5.9"). -- Tilting of milling units: 20°/ +45° in horizontal plane. -- Fixed left hand column to support head unit. -- Max. working height: 200 mm (7.8").

COMEVA - CUBE 3, ...Edgebander (Single Phase)The CUBE 3 from COMEVA is designed to be a very compact "every day" Edgebander. The CUBE 3 Edgebander is operated through a PLC control system with a touchscreen. The machine handles panel thicknesses of 0.315" up to 1.77" (8 mm to 45 mm), The coil feed accepts Edgebanding from 0.4 mm to 2 mm thick; strip material can be hand-fed.Equipped with: -- Heated infeed fence for optimum glue penetration. Large capacity Teflon coated glue pot (2.64 Lbs). -- Single motor End Trimming station -- Top & Bottom Trimming -- Top and bottom Buffing. -- Feed speed is variable between 9.8 & 23 FPM (3 - 7 MPM); feed chain pads with replaceable rubberized surface inserts. -- Rubberized holddown rollers with ball bearings for low friction and long life. Work stations: -- Pneumatically operated guillotine for up to 2 mm thick banding, followed by spring loaded double pressure rollers. -- Single front/rear trimming unit, 0.3 HP motor. -- Top & Bottom trimming units, (2) 0.5 HP motors. -- Top & Bottom buffing station, (2) 0.16 HP motors. -- Complete with: Safety enclosure protects the operator from noise and debris. Engineered & Manufactured by COMEVA S.L, in Spain.Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

COMEVA - NICRON 2C, ...CNC Door Machining Center with ATC and Flat Table for NestingSimple, robust, fast, and versatile CNC that can meet all your needs milling, drilling, trimming etc. passage and entry doors. Using available CAD software, it can also machine any designs such as raised panels on entry doors or special bevels on door jambs. - Equipped with a Flat Table compatible with nesting, Router milling motor, Double-End horizontal milling motor to work on edges of all types of doors is added to "free space" location. Also (see options below) for machining the hinges on door jambsMachine Specifications. Head Composition: -- Milling Router with Tool Changer capability, working in conjunction with the 6-position tool rack. This Router can machine the door knob/plate openings, rebate on edge of door frame. -- (1) Double-End horizontal Router Head: The Double-End spindle has one of the outputs with a cutter for machining the hinges and the second output has cutter for milling of the door latch opening.Worktable: -- REXILON Nesting type flat table slotted for vacuum distribution and with (12) pneumatic reference stops. -- Tool changer with 6-position tool rack on one side of table. -- (4) Independent vacuum zones; Working area is 2,600 x 1,300 x 200 mm (102" x 51" x 7.8"). -- Workholding can be achieved with zoned vacuum table (for milling on the top surface of doors and wider door jambs, raised vacuum cups for edge of doors and machining of hinges on door jambs (with optional jamb fixture device below).Control & Software: -- Mobile CNC control panel for all axes control c/w display, keyboard, and mouse. -- Powerful CNC Controller for machining control on all axes, reference stops, vacuum zones, and working groups; -- CADCAM Software is UCAMAM V11 (standard version) with: Postprocessor (which translates to language of machine) drawings from images such as BMP, JPG, TIF, GIF, PNG, as well as vector files from any format ADOBE Illustrator, DXF (CAD), EPS, PLT, TXT. Draw with this software directly and has auto-nesting to optimize use of the material.Drives & Speeds: -- ATC Router is 9 kW, 12,000 - 18,000 RPM with DELTA Inverter. -- Horizontal double-end unit is: 2.2 kW, 12,000 RPM. -- X & Y-Axe Speeds are: 10 MPM (30 MPM with safety barrier, faster speeds available); Z-Axis is 10 MPM. Other Machine Composition. -- Piston Stops: (12) Divided into (4) fields. -- Lineal Guides: H/Win 20 mm wide. -- Lubrication System: Central - manual. -- Vacuum Pump: 160 CBM/Hr, 7.5 HP. -- Standard machine voltage: 220 V, 50 - 60 Hz, 3-Ph (Transformers available). -- Overall Dimensions & Weight: 3,900 x 2,150 x 2,100 mm (154" x 85" x 83"); Weight: 2,300 kG (5,000 Lbs).Optional: - CE regulation (Light barrier and perimeter fencing ): ....................3,100 Euro- Raised (50 mm) Vacuum Cups. Recommend (8) @ 165 Euro......1

COMEVA C-400 B Programmable European Door Milling Machine: Specifications: -- Maximum door length, X-Axis 96" (2,440 mm). Maximum machining length from center to center of the farthest slots is 74.8" (1900 mm) based on a 120 mm hinge length. -- Working field Y-Axis 23.6" - 39.3" (600- 1,000 mm) min/max door width. -- Working field "Z" axis 1.18" - 2.36" (30 - 60 mm) min/max door thickness. Positioning: -- NC Controlled working table for X-, Y- & Z-axis part positioning & processing. X- Y- & Z- Axis movement via hardened round ways & ground ball screws.Work Table: -- (2) NC Controlled extruded aluminum support rails with (6) Non-Marking manually positioned pneumatic panel clamps. -- (1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles. Machining: -- (4) Manually adjusted 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets, RH rotation. -- (1) NC Controlled 3 HP (2.2 kW) air-cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation. -- (2) NC Controlled 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation.Operator & Machine Control: -- Separate control console with "ADTECH CNC 4640" Controller with numerical and function keyboard; -- Monitor displays programming graphics, machine data & subroutines, runs production programs while programming and editing -- Programming storage for 30 individual programs. -- Includes: Owner’s Manual with mechanical & electrical schematics. -- Engineered & Manufactured by COMEVA S.L, in Spain.

COMEVA - C-250, ...Programmable Door Milling Machine Specifications: -- Working field "X-axis" 90.55" (2,300 mm) max. door length. -- Working field "Y-axis" 23.6" - 39.3" (600 - 1,000 mm) min/max. door width. -- Working field "Z-axis" 1.18" - 2.36" (30 - 60 mm) min/max. door thickness. -- Positioning:NC Controlled working table for "X", "Y", and "Z" part positioning & processing."X", "Y", and "Z" Axis movement via hardened round ways & ground ball screws. -- Worktables:(2) NC Controlled extruded aluminum support rails with: (4) Non-marking manually positioned pneumatic panel clamps.(1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles -- Machining: (4) NC Controlled 0.5 HP (0.37 kW), 12,000 RPM air cooled "Hinge Plate" router spindles with: ERC 32 Collets & manual spacing adjustment, RH rotation.(1) NC Controlled 3 HP (2.2 kW) air-cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation.(1) NC Controlled 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation. -- Operator & Machine Control: Separate control console with: "DELTA" 12" TFT touch screen control with numerical and function keyboard;Monitor displays programming graphics, machine data & subroutines, runs production programs while programming, and editing.Programming storage for (30) individual programs. -- Complete with: 1-Year Mfg. Warranty, User's operator/maintenance manuals & backup disks. -- Available Options at additional cost:Additional 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets = $ 1,976.00 each.Additional 2 HP (1.5 kW) air-cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets = $ 3,240.00 each.Actual Model is COMEVA - C-250, ...CNC DOOR MILLING MACHINEIncludes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.

COMEVA - C-400 B Programmable, ...European Door Milling Machine: Specifications: -- Max. door length X-Axis 96" (2,440 mm); max. machining length from center-to-center of the farthest slots is 74.8" (1,900 mm) based on a 120 mm hinge length. -- Working field Y-Axis 23.6" - 39.3" (600 - 1,000 mm) min/max. door width. -- Working field "Z-axis" 1.18" - 2.36" (30 - 60 mm) min/max. door thickness. Positioning: -- NC Controlled working table for X-, Y- & Z-axis part positioning & processing; X- Y- & Z-Axis movement via hardened round ways & ground ball screws.Worktable: -- (2) NC Controlled extruded aluminum support rails with (6) Non-Marking manually positioned pneumatic panel clamps. -- (1) NC Controlled extruded aluminum support table for "Hinge Plate" router spindles. Machining: -- (4) Manually adjusted 0.5 HP (0.37 kW), 12,000 RPM air cooled "Hinge Plate" router spindles with ERC 32 collets, RH rotation. -- (1) NC Controlled 3 HP (2.2 kW) air cooled 12,000 RPM horizontal "Case Lock" router spindles with ERC 32 collets, RH rotation. -- (2) NC Controlled 2 HP (1.5 kW) air cooled 12,000 RPM vertical "Hardware" router spindles with ERC 32 collets, RH rotation.Operator & Machine Control: -- Separate control console with: "ADTECH CNC 4640" Controllers touch screen control with numerical and function keyboard. -- Monitor displays programming graphics, machine data & subroutines; runs production programs while programming and editing. -- Programming storage for (30) individual programs. -- Includes: Owner’s Manual with mechanical & electrical schematics and parts breakdown; covered by a 1-Year Factory Warranty on parts.Available Options at additional cost (when ordered with machine from the factory): -- Additional 0.5 HP (0.37 kW), 12,000 RPM air-cooled "Hinge Plate" router spindles with ERC 32 collets at ...$ 1,976.00 each. -- Engineered & Manufactured by COMEVA S.L, in Spain.

COMEVA NICRON CNC Door Machining Center: Flexible Door Machining Center to machine Hinges, Locks, Grooves, etc. A device to allow machining of door jambs is an option available. Also vertical top router head with Automatic Tool Changer is available. See options below.Specifications: -- Max. door length, X-Axis 102.3" (2,600 mm). -- Max. door width, Y-Axis 47.2" (1,200 mm). -- Max. travel on Z-Axis 7.87" (200 mm)Working Heads: -- The machine is equipped with a (2) motors/heads 5 HP (3.5 kW) - 12,000 RPM each, routing/milling units: (1) vertical unit and (1) horizontal double spindle head.Working table: -- Table dimensions: 51.2" x 102,3" (1,300 x 2,600 mm). -- Manual table loading system with vacuum cup hold-down for the doors. For the optional jamb (door frame) table fixturing includes an air cylinder clamping system.Operator & Machine Control: -- Separate mobile control panel with powerful CNC to handle all the functions of the machine. -- Includes the unique COMEVA DOOR Software specially designed for machining of doors. It controls the movements of all axes, reference stops, vacuum zones and workgroups. It is user-friendly with macros(subroutines) for most of the hinges/locks on the market so operator can input the job parameters instead of complicated programs.Complete with: -- Users operator/maintenance manuals & back up disks.Engineered & Manufactured by COMEVA S.L, in Spain. - Stated price includes Machine (Jamb device not included), Software and Safety Barrier.Includes: Owner’s Manual with schematics; covered by a 1-Year Factory Warranty on parts.

COMEVA - NICRON DOOR C, ...CNC Door Machining Center with Automatic Tool Changer Flexible Door CNC Machining Center that can machine: Hinges, Locks, Door Face Patterns and many similar applications. A device to allow machining of door jambs on the same machine is an available option. See options below. -- Working Heads: -- (2) Heads; (1) Vertical with 12 HP (9 KW) - 12,000 RPM routing/milling units: and (1) Horizontal - double spindle (opposing spindles) unit, 5 HP (3.5 KW). -- Working table: Rails with suction cups holddown. -- Working area:: 43.3" x 125.98" (1,100 x 3,200 mm). -- Manual table loading system with vacuum cups for the doors. For the optional Jambs (door frame) table fixturing includes an air cylinder clamping system. Working Height is 220 mm (8.7"). -- Includes: Servomotors for gantry feed; 100 FPM (30 MPM.) axes locating movement with SI lineal guides; ( (4) Piston stops. Auto Lubrication system; Venturi for suction cups. Operator & Machine Control: -- Separate mobile control panel with powerful CNC to handle all the functions of the machine. -- Includes the unique COMEVA DOOR Software specially designed for machining of doors. It controls the movements of all axes, reference stops, vacuum zones, and workgroups. It is user-friendly with: Macros (subroutines) for most of the hinges/locks on the market so operator can input the job parameters instead of complicated programs. -- COMEVA DOOR PRO is additional CAD/CAM type software with capability to design your own CAD programs and post processor to load into machine. This software would be loaded on users own PC. -- Comes with: Owner’s Manual with schematics software disc/USB; covered by a 1-Year Factory Warranty on parts (Electrical components carry six months warranty). Also includes safety light/barrier meeting CE standards. -- OPTIONS: Increase door width capacity(Y-Axis) from 43.3" (1,100 mm) to 47.2" (1,200 mm) door width.. Also available with or without the door jamb fixture. With this device, the jambs are mounted on the same table and machined as a separate operation before or after the doors. -- This "new" model NICRON DOOR C is a similar machine (to NICRON DOOR, see DM-300044), but the vertical head is capable of working as an Automatic Tool Changer (ATC). A tool rack holding up to (6) different tools is added at the end of the worktable and is programmable via the same CNC controller. -- Machine dimensions 2100 x 3900 x 2100 mm (83" x 154" x 83"). Gross weight; 6450 Lbs (2,390 Kgs.). --Engineered & Manufactured by COMEVA S.L, in Spain.

ELGI EGRD 500 Refrigerated Air Dryer (480 CFM)The ELGi EGRD 500 refrigerated dryer is designed to provide a constant 41ºF dew point and utilizes the latest advancements in refrigeration technology to provide low operating cost and years of trouble-free performance.The advanced “ALU Dry"; aluminum heat exchanger module enables the packaging of the pre-cooler, evaporator, separator, and reheater all in one compact unit. This reduces the size, weight and pressure drop associated with conventional exchangers and optimizes the overall performance and reliability of the dryer which ensures effective removal of condensed liquids regardless of flow.Features: -- Microprocessor Controls with Dew Point Display Indication -- All-In-One Aluminum Design Exchanger -- Low-Pressure Drop -- Ozone Friendly Refrigerant -- De-Mister Type Moisture Separator -- Environmentally Friendly Refrigerant -- Hot Gas Bypass for Constant Dew Point -- Extended Service Life -- Timer Drain Options Include: ELGI Pre-filter AF 0520P rated at 520 SCFM, 1-1/2" NPTPremium Filter Series is constructed from premium materials and features with ease of installation and service in mind. Filter elements have a unique push-fit, double O-ring design to ensure no contaminants get down stream. Features: -- High Quality Aluminum Construction -- Automatic Internal Float Drain -- Pop-up Filter Change Indicator

ELGI EN07-125 10 HP Rotary Screw Compressor; 38 CFM @ 125 PSIG.Equipped with: -- Efficient air filtration system where air enters through a pre-filtered enclosure. -- After cooler is standard on all models to enable high efficiency TEFC, Super E, 10 HP motor operation up to 115°F ambient temperature.Complete with: -- "Neuron" controller that has been custom designed and engineered to monitor and control overall performance. -- Includes service indicators, fault alarms, safety shutdowns and a service / operational log feature for real-time feedback. -- Phase monitor, auto re-start and the ability to hook up to a RS 485 connection to monitor system remotely.Includes: -- 3-Stage efficient air-oil separation (less than 2 PPM). -- Single door access to routine maintenance points. -- Spin-on oil filter and separator elements for fast and easy routine service.6-Year Air End Warranty. - UL/cUL certified to ensure high levels of safety.Recommended option: F10104 / MICRO 50 Clean Resources F10104 / Micro 50 Clean Resources F10104 Oil/Water Condensate Separator - add;...$ 500

ELGI EG30-125 Rotary Screw Air Compressor; 40 HP - 170 CFM @ 125 PSIG40 HP Rotary Screw Compressor (Direct Drive); Air-End equipped with "eta-V" profile rotors. Equipped with: -- 4/5 Lobe combination designed to run at optimum speeds; low operating speeds for extended life, low maintenance and a reduced sound level; Intake Valve System with integrated blow down unit, solenoid controls & actuators designed for low losses. -- Optimal Capacity Control results in a direct saving on power consumption; air-oil separation with OSBIC process means oil-free air (1 PPM), per ISO standards and increasing the life of the separator element. -- Features: -- Efficient air cooling system; "Smart" cooling system maintains a lower temperature which increases the motor life, enables easy maintenance and the ducting is completely insulated internally from the other zones. -- Robust, reliable and able to perform at extreme temperatures - from cold to hot and from dry to extreme humid conditions. -- Complete with: -- Performance Control System's user-friendly intuitive backlit display for easy reading; remote monitoring through an RS485 connection; optimal pressure sensors monitor compressor internal pressure differences to optimize compressor maintenance. -- Includes: -- Phase Monitor, Auto Restart; custom designed, centrifugal type moisture separator with an automatic timer control drain which removes over 99% of bulk water from the compressed air.LIFETIME Air-End Warranty

ELIO VALERI ELVAP 120 Copy Lathe. -- General data: 48" max. length cap., 7" max. dia. without steady rest, 3.93" max. dia. with steady rest, and up to 2.5" x 2.5" dia. with steady rest for square pieces; 0 - 39 FPM forward and 0 - 52 FPM return speed, 5.5 HP motor, 1,300 - 3,500 - 5,000 RPM; -- Features: Air/oil feed and copier, chain head stock drive, gate loading, pattern; pneumatic tail stock, automatic pneumatic control program.

EMC MERCURY 1350 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pneumatic pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,350 mm (53"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 2,200 mm (86-5/8") x (width) 1,320 mm (52"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 180 mm (7"), spirally grooved. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- Motor power 11 kW (15 HP) driving both heads, with soft starter. -- On/Off Selector control with pneumatic piston to select roller. -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 140 mm (5-1/2"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- New pneumatic aluminium sanding pad, lamina 40 mm. With On/Off selector. -- Quick Change System for removable pad with felt, rubber and graphite. -- Rotating cutting speed 18 m/Sec (59 FPS). -- Driven by same main motor, with soft starter.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 19 m/Min (10 - 62 FPM). -- Table rollers. Extension supports with idle rollers in infeed & outfeed.Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meter on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". -- Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brake on main motor. -- Automatic emergency stop and alarm displayUSA UL or Canada CSA Safety Features

EMC EXPLORER 1100 2RK ... Wide Belt Sander with (2) Sanding Heads; Roller and Combination head roller/pad.Versatile, medium duty machine, ideal for cabinet shops etc.TECHNICAL DATA: -- Useful working width 1,100 mm (43"). -- Working thickness min./max. mm 3 - 170 (1/8" - 6-11/16"). -- Abrasive belt dimension (length) 1,900 mm (75") x (width) 1,120 mm (44"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Head configuration:1st Head: Steel Contact Roller -- Roller diameter 142 mm (6") -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. -- Motor power 11 kW (15 HP). -- Automatic Star-delta starter. -- Speed rotation: 18 m/Sec (59 FPS).2nd Head: Combination Roller & Pad. -- Roller diameter 142 mm (6"). -- Rubber covered roller with hardness 45 Shore. -- Automatic abrasive belt grit compensation with "Grit-Set System". -- On/Off Selector control with pneumatic piston to select roller. Flexible sanding pad. Quick Change System for removable pad with felt, rubber and graphite. Rotating cutting speed 17 m/Sec (55.8 FPS). --Driven by same main motor.Abrasive belts oscillation by means of electronic photocell sensor.Feed System: -- Working thickness min./max. mm 3 - 190 (1/8" - 7-1/2"). -- Motorized table lifting including fine adjustment, on 4 precision screws. Natural rubber conveyor belt, machined. Automatic feed belt centering device. Electronic digital display for working thickness; resolution 0.1 mm (0.004"). -- Feed belt speeds adjustable by electronic inverter from 3 to 17 m/Min (10 - 55 FPM). Centralized Control Cabinet: -- Control panel with self-diagnostics alarm control unit. -- Analog load meters on main control cabinet. -- Table lifting-lowering thickness system, electrically controlled. -- AUTOMATIC Delta - Star starter on main motor and IP 54 protection against dust & moisture. Centralized Independent Pneumatic Control Cabinet: -- Pneumatic air filter with automatic water-drain system. -- Pneumatic adjustment for "Grit set system". --Pneumatic plant working without lubrication. Compressed air pressure 6 bar (85 PSI). IP 54 protection against dust & moisture. Safety Features: -- Anti-kickback infeed protection. -- Oversized parts infeed protection by swinging bar. -- Emergency push buttons front & rear. --Automatic brakes on main motor. -- Automatic emergency stop and alarm displayOption: TAMPICO Cleaning Brush, 150 mm (6") diameter. Please add ...$3,400USA UL or Canada CSA Safety Features

EMC MERCURY 1350 3WRK Abrasive Planer / Wide Belt Sander with (3) Heads; Planer Head, Contact Roller, and Combination Head.Useful working width 1,350 mm (53"). Working thickness min./max. 3 - 170 mm (1/8" - 6-11/16"). The machines uses abrasive belts 2,620 x 1,370 mm (103" x 54") for longer life of the sanding belts.Head configuration:1st Head: Planer Head "W" -- Cutter head knives diameter 140 mm (5-1/2"). -- Shaft for helicoidal position knives with (380) Interchangeable knives with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 20 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer. group in working position. -- Working pressure adjustment. -- Motor power: 15 kW (20 HP). -- Automatic Star-delta starter. -- Speed rotation: 32 m/Sec (115 FPS). -- Soft starter for slow starting2nd Head: Steel Roller "R", Belts dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 180 mm (7"), spirally grooved. -- Electronic motorized roller pressure adjustment "Grit-set system". -- On-Off selector switch control for roller. -- Constant control to any position with accuracy 0.02 mm. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with Automatic star-delta starter. -- Abrasive Belt cutting speed: 18 m/Sec (59 FPS). -- Timing oscillating cleaning abrasive belt blower located at the bottom 3rd Head: COMBINATION Unit "K", Belt dimensions: 2,620 x 1,370 mm (103" x 54"). -- Roller diameter: 140 mm (5-1/2"). -- Roller rubber hardness 45 Shore, Constant control to any position with accuracy 0.02 mm. -- On-Off selector switch control for 3rd roller including pneumatic piston -- Pneumatic Aluminum PAD , lamina 40 mm, On-Off. -- Quick changing system, extractable blade with felt, rubber and graphite. -- Rotation: Against feed (clockwise). -- Motor power: 11 kW (15 HP) with automatic star-delta starter. Abrasive Belt cutting speed:18 m/Sec (59 FPS).Feed system: -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 18 m/Min (9.8 - 58 FPM) Inverter Controlled. -- Automatic feed belt centering device. General Machine Features: -- Large diameter screws on machined guides with columns and pistons. -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each (head) working group. Electronic programmable color TOUCH SCREEN display, 7" wide -- PLC with micro-processor of latest generation, modular and expandable. -- Connection USB, RS232, Ethernet 10/100/1000. -- Memory capacity: 100 working programs or more. -- Graphic synoptic to facilitate programming.Software facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickn

EMC GIANT 1350 2WR Abrasive Planer with (2) Heads, Planer Head and RollerTop of the line Heavy Duty Abrasive Planer from EMC. The series of GIANT machines are available in many configurations. Abrasive Planer has a helicoidal head with insert tooling.Useful working width 1,350 mm (53"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8").Head configuration: 1st Head: Planer Head "W" -- Cutter head knifes diameter 180 mm. -- Shaft for helicoidal position knifes with (512) Interchangeable knifes with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 24 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer group in working position. Working pressure adjustment. Motor power 30 kW (40 HP), Star-delta starterSpeed rotation: 35 m/Sec (115 FPS).2nd Head: Roller "R" Belts dimensions: 3,250 x 1,370 mm (128" x 54"). -- Roller diameter: 320 mm (12-5/8"). -- Roller rubber hardness 45 Shore. Constant control to any position with accuracy 0.02 mm. -- On-Off pneumatic piston, controlled from the electrical panel. -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (99 FPS). Blower for the roller unit.Feed system: -- Constant pass line, 900 mm (35.4") from floor (In line machine). -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 20 m/Min (9.8 - 65.6 FPM). Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronic programmable color TOUCH SCREEN display, 7" widePLC with micro-processor of latest generation, modular and expandableConnection USB, RS232, Ethernet 10/100/1000Memory capacity: 100 working programs or moreGraphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, programming and display for thickness. -- Command, programming and display for feeding. -- Command, programming and display for all inverters. -- Command, programming and display for selected groups. -- Command, programming and display for blowers, including compressed air saving function. -- Display report and reset of alarms (self diagnostic) with memory records.Options Included: -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Rotating blowers for part and feed belt cleaning. -- LED light inside the machine. -- Telemetry for remote computer assistance

EMC GIANT 1350 3WRF Abrasive Planer with (3) Heads, Planer Head, Roller and Superfinishing PadTop of the line Heavy Duty Abrasive Planer from EMC. The series of GIANT machines are available in many configurations. Abrasive Planer has a helicoidal head with insert tooling.Useful working width 1,350 mm (53"). Working thickness min/max mm 3 - 170 (1/8" - 6-5/8"). Head configuration:1st Head: Planer Head "W" -- Cutter head knives diameter 180 mm (7-1/16"). -- Shaft for helicoidal position knives with (512) Interchangeable knifes with 4 cutting edges, 14 x 14 x 2 mm. -- Sectioned pressure bars in 24 independent segments. -- Anti kickback protection made of 72 independent elements. -- On-Off pneumatic cylinder for planer group in working position. Working pressure adjustment. -- Motor power 30 kW (40 HP), Star-delta starter.Speed rotation: 35 m/Sec (115 FPS).2nd Head: Roller "R" Belts dimensions: 3,250 x 1,370 mm (128" x 54"). -- Roller diameter: 250 mm (9-13/16"). -- Roller rubber hardness 60-65 Shore. Constant control to any position with accuracy 0.02 mm. -- On-Off pneumatic piston, controlled from the electrical panel. -- "Grit-set system". -- Rotation: Against feed (clockwise). -- Motor power: 22 kW (30 HP) Automatic star-delta starter. Rotating cutting speed: 21 m/Sec (99 FPS). Blower for the roller unit.3rd Head: SUPERFINISHING PAD "F" Electronic PAD segmented in (75) sections. -- Belts dimensions: 3,250 x 1.370 mm (127-15/16" x 54"). -- Width of a single element (section): 18 mm (11/16"). -- APC - Automatic Programmable Control and setting of the air pressure. -- Electronic motorized roller pressure adjustment "grit-set system". -- Rotation: Against feed (clockwise). -- Timed oscillating abrasive belt "air jets" cleaning. -- Motor power: 18,5 kW (25 HP) with electronic inverter variable abrasive belt speed 3 to 18 m/Sec (9.8 - 59 FPS).Feed system: -- Constant pass line, 900 mm (35.4") from floor (In line machine). -- Vacuum bed, 4 kW (5,5 HP) for hold down of smaller parts, mounted inside of the machine base. -- Idle table rollers support in infeed and outfeed. -- Rubber covered presser rollers, grooved. -- Variable feed belt speed, adjustable from 3 to 20 m/Min (9.8 - 65.6 FPM). Inverter Controlled. -- Large diameter screws on machined guides with columns and pistons. -- Automatic feed belt centering device.General Machine Features: -- Independent main motors. -- Analog ammeters, for each motor, on main control cabinet. -- Electronic motorized grit set system, control from touch screen for each working group.Electronic programmable color TOUCH SCREEN display, 7" widePLC with micro-processor of latest generation, modular and expandableConnection USB, RS232, Ethernet 10/100/1000Memory capacity: 100 working programs or moreGraphic synoptic to facilitate programmingSoftware facilities: -- Automatic motor sequence starting. -- Command, programming and display for all electronic pad functions. -- Command, program