SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023) Specifications: Cap. 111 ACFM. Rated pressure 60 - 125/135 PSIG. Noise level 85 dBA. Equipped with: E-Profile rotor design air end. 30 HP 3,530 RPM Motor. Air-cooled aftercooler. SULLAIR “SUPERVISOR II DELUXE” Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

SULLAIR 10B-50 ACAC Rotary Screw Compressor (Open Type)Specifications: -- 50 HP - 1,770 RPM Motor, rotary screw air end, 100-110 max. PSI, approx. 180 ACFM; (2) asymmetrical lobe profile rotors only make contact on a lubricated pitchline to virtually eliminate cap. or efficiency loss. -- Equipped with: -- Tapered roller bearings on discharge and cylindrical bearings on inlet for high load carrying capacity. -- Pressurized fluid lubrication & cooling of Compressor with rigid piping & tubing; efficient 2-stage air/oil separation with replaceable element. -- Spin-on fiberglass fluid filter, Heavy Duty inlet air filter, cap. modulator stabilizes system pressure and matches output to demand (minimizes need for air receiver & reduces wear caused by start/stop). -- Includes: -- Electro-mechanical gauges & controls, air after-cooling.

SULLAIR ES8-30H/A 30 HP Single-Stage Fluid Rotary Screw Air Compressor, with 53,186 Run & 49,602 Load Hrs. (As of 11/2023)Specifications: -- Cap. 111 ACFM. -- Rated pressure 60 - 125/135 PSIG. -- Noise level 85 dBA.Equipped with: -- E-Profile rotor design air end. -- 30 HP 3,530 RPM Motor. -- Air-cooled aftercooler. -- SULLAIR “SUPERVISOR II DELUXE"; Microprocessor controller & graphic monitor system, with LCD Display, Touchpad, Constant pressure & temperature readout of pressure, Power failure auto restart, & Automatic start/stop.

SULLAIR LS-10, 30 HP SCREW AIR COMPRESSOR: -- Specifications:30 HP Motor, rotary screw air end, approx. 115 PSIG - 125 PSIG max; Mounted upon 150 Gal. receiver tank.Approx. Dimensions: 64" x 32" x 65"; Approx. Weight: 2,500 lbs. -- 2,630 Approx. total operating hours. Hour meter: Inoperable.

SULLIVAN PALATEK D185PJD AIR COMPRESSOR (GAS/DIESEL): -- Specification:Mobile Air Compressor with JOHN DEER 4024TF281A, 2.4 L (4) cylinder diesel engine; PINTLE hitch. 29-Gal single fuel tank, 210 CFM (5.9 m³/Min.) @ 100 PSIG., idle speed 1,650 RPM, full load speed 2,500 RPM. -- Equipped with:Tapered roller bearings, adjustable pressure from 70 - 100 PSIG. large, 108 mm & 127 mm dia. twin screw air end & automatic 0 - 100% capacity control, with two stage dry type air filter, oil level sight gauge.One-piece canopy removable in a matter of minutes for ease of serviceability and maintenance. Pitched roof to allow water drainage, meets 2010 US EPA sound requirements. 15" Wheels with steel belted radial tires. -- (1,893) Hours on the unit.

SUMMIT PR-9S 2-Ram Horizontal Baler -- Motor: 60 HP. -- Main Cylinder: 9". -- Eject Cylinder: 8". -- Feed Opening: 60" x 44" x 46". -- Cranston Wire Tie. -- Infeed Conveyor. -- Loaded onto your Truck.

SUPERMARKET SERVICES 30" x 30" x 42" H Dual-Chamber Portable Automatic Vertical Hydraulic BalerSpecifications: -- Chamber size 30"; x 30"; x 42"; H. -- Bale size 30" x 30"; x Approx. 24"; H. -- Stroke: Approx. 16".Equipped with: -- 5 HP Hydraulic unit, with 1,720 RPM TEFC Motor. -- (2) Swivel & (2) Fixed casters.

SWEED MODEL 517 SCRAP CHOPPER With Dump HopperFeatures: --The Model 517 XHD provides a large cutting capacity. This is the chopper of choice for custom applications or for operations converting substantial quantities of linear scrap materials. Prepared for an abusive environment, the 517 XHD has a strong 1/2"; plate steel housing. The 517 XHD also features a magnetic starter to protect workers from an unexpected restart after loss of power. The powerful air activated feedworks is controlled with a footswitch for operator safety, and is also capable of despooling scrap wire and cable from reels. --Additional safety options are available. Material Reference The recommended model of scrap chopper is determined by scrap size, scrap volume, and requested custom features. Please consult a SWEED representative to determine the appropriate scrap chopper for your application.» High-tensile bale wire» Small, solid, aluminum and copper bars» Jacketed and non-jacketed wire and cable» For other materials, consult SWEED --Electric Motor 5 HP --Infeed Opening 6 "; W x 1 "; H Cut Length 3 ½"; standard (smaller cut lengths available with different knife configurations) --Number of Stationary Knives 1 --Number of Rotating Knives 1 standard --Overall Chopper Dimensions 56"; L x 34"; W x 30"; H --Chopper Weight 1,492 lbs --Chopper Shipping Weight 1,577 lbs -- Include Stand and Gaylord

TANA- SHARK 440DT, ... Portable Dual Shaft ShredderSpecifications: -- Approx 3900 Hours and New in 2015 --Bolt-on cleaning combs for easier maintenance --Magnet conveyor improvements - Discharge side to be selected from TCS + hydraulic magnet adjustment during operation --Rated power (SAE J1995) 399 kW (535 bhp) @2100rpm --Nominal torque 324,530 ft-lbs 440 kNm --Rotor length 9 ft 10 in --Number of rotor knives 33 / 44 --Screen sizes Available from Tana- 1.9", 3", 3.5", 3.9", 4.3", 4.7", 5.5", 6.6", 8.7", 10.8" --Screen area 29.6 sq ft

THOMAS TURNBAK Return Conveyor for EdgebandersTHOMAS "Turnbak" 90" L x 120" W Automatic Return Conveyor: Left-hand feed, right-hand return layout. - Adjustable table pass-line, 32" to 38" height. -- Infeed Receiving Conveyor: 90" L x 120" W with 49" W; line-shaft PVC covered rollers. Rollers 1-7/8" dia. on 4" centers. -- Return Conveyor: (3) Sections; 84" L x 49" W, and (1) section 60" L x 49" W; powered return conveyor; line shaft driven; PVC covered rollers. -- Transfer Table: Pneumatic actuated automatic table pop-up with photo-eyes. (12) 1/2" Dia. rubber cross conveyor belts (dimensions 90" L x 49" W). -- (3) Transfer belts need replacing. -- Includes: (1) Section of 48" L x 49" W; non-powered Return Conveyor. -- LEESON Inverter with: 2 HP LEESON Motor. -- With: Adjustable control system and operator manual. -- The transfer process occurs on a continuous basis. -- (3) Transfer belts need replacing. NOTE: Needs(3) Transfer Belts; actual model number: 90 x 120 4C

THOMAS MFG TURNBAK R1 70x96 Return Conveyor System:Line shaft powered roller (PVC covered) for LEFT-HAND Feed & RIGHT-HAND Return Conveyor System. Specifications: -- 70" Long x 96" Wide receiving table; transfer system will handle a panel 96" long x 62" wide max. size (min. 6" x 6"); -- Variable speed up to 120 FPM. -- Automatically receives-and-transfers panel with (10) transfer belts onto the return side and onto a 36" wide & 96" long return conveyor. (approx. 8' long) which conveys panel back to the operator. -- Variable speed from 0 - 120 FPM. -- NOTE: Was previously attached to & used with a 2014 Biesse Akron 1440A Edgebander, see EXF Listing ..."EO-012637"

TORIT 360-IRD-15 Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Down flow air pattern allows airflow and gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure dropSpecifications: -- 15 HP direct drive, floor mounted blower. -- 4,800 CFM @ 8" wg, 4,050 CFM @ 9" wg, 2,400 CFM @ 10" wg -- (21) Dura-life filter bags with a cloth area of 192 sq. ft. -- (3) Collection points for plastic collection bags.

DONALDSON-TORIT - 376RFW-10 or 12: Dust Collector45,000 CFM @ 9.7:1 Air-to-cloth ratio; 140" dia. round baghouse with: (376) filter bags of 10' length (oval bags provide for radial movement of bag during cleaning for longer life), total 4,632 sq./ft. filter area. -- Filtration media cleaning via a floor mounted 7.5 HP medium pressure Air Pump (eliminates the need for compressed air, which can be susceptible to condensation and freezing); 36" x 65" return air outlet and 48" x 48" inlet for dust laden air. -- Includes: Rotating cleaning air manifold driven by 0.33 HP motor; (1) NEMA-9 solenoid and diaphragm valve which rotates over the bag openings; walk-in plenum for bag access/maintenance. -- Galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed; walk-in access door at top of ladder. -- Equipped with: Structural steel support; maintenance platform; caged ladder; bolt-on involute arm; explosion doors (need to be replaced). -- Includes Backward inclined FAN EQUIPMENT: Size 7 BCS floor-mounted Fan set at 45,000 CFM @ 15" SP belt driven at 1,485 RPM; powered by a 200 HP TEFC Motor via OMRON/IDM E7 Series Inverter. -- 24" Rotary Air Lock at the bottom of the 60° hopper. -- Complete with: Pictured electrical controls are included. -- NOTE: New 200 HP electrical motor was replaced recently. -- Unit had an accidental fire at bottom section near hopper causing the explosion doors to burst. Unit still working as they are not returning the air. Can be sold with or without replacement of doors; Cost of which is negotiable. -- Professional dismantling and rigging available at extra cost. Please call!

TORIT/DAY 156RFW10 Dust Collector with Rotary Air Lock and Non-Return Valve & Fire Prevention.20,300 CFM at 10:1 Air-to-cloth ratio, (156) filter bags 10' long providing a total 2030 sq. ft. of filter area; filtration media cleaning via 3 HP medium pressure air pump eliminating the need for compressed air which can be susceptible to condensation and freezing. -- Rotating cleaning air manifold driven by 0.33 HP motor, uses only (1) Nema-9 solenoid and diaphragm valve which rotates over the bag openings; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. -- Clean air side fan assembly with 24ACF CLASS I-III fan driven by a 40 HP TEFC motor. Depending on Air-to-Cloth ratio needed this fan is undersized,ie. about 12,000 CFM and can be upgraded or 2nd fan used. TORIT "16 AN" 16" rotary air lock at the bottom of 60° hopper. -- Features: (2022) AIRCOM/BOSS PRODUCTS. NRVC Non Return Valve Combo. Extinguishing Box. GM SYSTEMS GMCU161SD-FM Fire Prevention Control Unit which manages 5 independent lines (16 program inputs & 5+10 outputs) - FM Certified. RAPTOR SERIES with related RAPTOR SPARK RS-BOX02.(IR) -- Complete with: Walk-in plenum, maintenance platform, caged ladder & support structure, electrical control panel. -- Includes: Outdoor piping. Barely used since bags were replaced. -- Please inquire for dismantling & rigging quotations

DONALDSON TORIT - 232 RF-8, ...24,000 CFM Baghouse Dust Collector (refurbished 2017) with: Rotary Air Lock & AIRCOM 32" Dia. Explosion Isolation Flap Valve (New 2017) -- Specifications. Approx. 10-1/2' Dia. x 24' H Baghouse with: 7-1/2' H Cone bottom & (232) 8' L cloth filter bags totaling appx. 2,414 sq./ft. of cloth area.Air-to-cloth ratio: 9.94:1; Overall system footprint: 25' x 25'. -- AIRCOM - SNR 800. ...32" Dia. SNR (Safety Not Return) Explosion Isolation Flap Valve: S/N 0977003 (2017); certified ATEX EN 15089; Class 2, NFPA Compliant with: Max. air speed 30 m/s; max. dust concentration: 4 LEL; Kst max. 299 bar m/s; pred. max. 0.25 bar, Pmax. 9 bar; Pipe structure to withstand pressure: 0.25 bar; Explosion resistance of flap 850 mbar;, Min. ignition energy 3 - 10 mJ; Min. ignition temperature 420° C (788° F); Temperature range: –20° C to +60° C (-4° f to 140° F); Range of applicable volumes: 10 - 60 cu. meters (33 - 196 cu./ft.); Anti-opening locks on both flaps. -- 75 HP - 1,780 RPM, TEFC Motor Driving Blower: Rated at 24,000 CFM @12" SP with: 36" Dia. inlet & 30" x 36" outlet. -- KOGER - SIZE 12, ...Rotary Air Lock with: 12" Dia. inlet & outlet 1 HP Motor. -- MURPHY-RODGERS - MRT-12, 10 HP Blower: S/N 1272 with 12" dia. inlet & 8" x 11" outlet. -- ROOTS - 32 U-RAI, ...5 HP Lobe Blower: S/N 0802963165. -- Electrical controls included. -- Actual model is: "232FRW8" (Walk-in unit); estimated shipping weight: 15,500 Lbs. -- Available 1st wk in July or sooner if needed.

TORIT - 460-IRD-20: Dust CollectorAn easy and economical solution for a wide range of wood dust collection applications. Downflow air pattern allows airflow & gravity to move filtered dust to collection receptacles for longer bag filter life and reduced pressure drop.Specifications -- 20 HP Direct drive; floor mounted blower. -- Fan inlet: 17". -- CFM: 7,000. -- Set of filter bags. -- Steel elbow from fan to collector. Motor Starter included.

TORIT-DONALDSON ADMC AD8 DRYFLO Cartridge Dust Collector. A Mist collector designed for long-lasting high collection efficiency capture of coolant and machining oil mists in metalworking applications. Even smaller amounts of dust can be filtered in the dirty air stream. -- DRYFLO is a proprietary cartridge which outperforms electrostatic precipitators and mist collectors utilizing standard HVAC envelope and cassette filters. Filter unit features a unique air-side filter retention system allowing for quick filter changes with minimal worker contact with collected oil. -- Also feature three-stage Filtration via a.) prefilter, b.) wrap allowing, c.) the filter cartridge to drain and coalesce smaller coolant mist droplets in to larger droplets. Plus optional fourth stage HEPA filters available for applications where smoke exists or additional efficiency of discharge air is required. -- Overall data: Capable of 17,600 CFM; (8) Filter Cartridges, 1,760 sq. ft. of filter area, -- Complete with: Ground mounted fan powered by a 40 HP motor, belt-driven. Fan includes a variable volume inlet. In prior application clean air was not retruned to building. -- Blower currently setup for approx. 15,000 CFM with 40 HP, Baldor Super-E, 324T frame, 1.780 RPM motor. -- Enclosure dimensions: 133" long, 68" deep, 160" high. Filter weight is 7,300 lbs.

CAM-WOOD XL300/5116 DIP CHAIN GANG RIPSAW12" Width cap.; 5-5/8"; max. cutting depth; 14"; min. stock length; Designed to meet the exacting standards required for high quality production line use. CAM-WOOD’s Rip Saws are manufactured to precise tolerances, and feature the newest designs for operator safety and volume productionSpecifications: -- Accepts saw blades from 12"; to 16"; diameter. -- Arbor is 70mm dia. with (2) keyways -- Saw arbor is powered by a 60 HP motor driving the spindle at 3,200 RPM; Soft start starters and low voltage controls are standard equipment. -- Feed chain is powered by a 2 HP motor with variable chain speeds from 8 to 80 FPM; feed chain is 12"; wide -- Table is 28"; wide x 67"; and 12"; between the column and the 1st saw blade. -- (2) Integrated 6"; dia. dust extraction connections.Complete With: -- (1) 70 mm ID saw sleeve with (2) keyways and the following spacers: (4) 15 mm, (4) 10 mm, (18) 1 mm, (10) 0.5 mm, and (8) 0,25 mm (see drawing after the "literature link). -- Two (2) rows of anti-kickback fingers mounted on the top and one (1) row from the bottom (total 3 rows) provides maximum safety protection. Equipped with: -- Precision fence ensures absolute accuracy between blade & fence, equipped with measuring ruler gauge. -- Power raise and lower to the arbor. -- Heavy-duty industrial motor for powerful cutting capacity. -- Ruggedly constructed cast iron frame for durability usage. -- Variable feed speeds enables the machine to meet different work requirements. -- V-way track and chain block surface are heat-treated for long wear resistance. -- Automatic lubrication to V-Way track facilitates chain longevity smoothness -- Automatic chain lubrication device equipped with an alarm that sends signals upon a lack of lubrication oil. Features: -- Precision built saw head ensures accuracy for straight line rip saw operations. -- Four (4) bearing spindle ensures rigidity & long life. -- Saw arbor is manufactured from NI-Cr-MO alloy steel for durability and anti-fatigue; spindle is heat treated, precision ground and balanced to provide the utmost in precision cutting performance -- Four (4) pressure rollers & two (2) hold-down plates for precise cutting of large and small workpieces. -- Ten (10) groove pulley and V-Belt arrangement ensures maximum motor output, excellent HP delivery to the saw spindle, and guarantees proper power transmission for heavy-duty multiple rip cutting. -- Adjustable guide rollers make cutting straight for slight radials material; they also secure glue joint at short pieces or long stacks.Options when ordered with machine: -- Additional saw sleeves (sleeve only), each, $415 -- Additional saw with spacer set consisting of: -- (2) 50 mm -- (3) 25 mm -- (4) 10 MM, -- (18) 1 MM -- (10) 0.5 MM -- (8) 0.25 MM -- Add per Sleeve with Spacer Set, $795 -- Laser Light with Mounting Bracket, each $1,190 -- Power raise & lower of the hold-down system when ordered with

CAM-WOOD MODEL TRS-1200TB SLAT RIPPER - (1) Top & (1) Bottom Rip Spindle.The machine can plane or shape the wood on two surfaces and then rip it. Ideal for shutters, louver slats, yardstick blanks, etc.Features: -- Special profile hold down & groove table for slat ripping, optional -- Designed to meet the exacting standards required for high-quality production line use. -- CAM-WOOD’s Slat Rip Saws are manufactured to precise tolerances and feature the newest designs for operator safety and volume production. -- All of these features combine to show what a true value these machines are in today’s highly competitive market. -- Precision fence assures absolute accuracy between cutterheads & fence and is equipped with a measuring gauge. -- Double anti-kickback fingers mounted at the infeed end of the machine provided maximum safety protection. -- Heavy-duty industrial TEFC motor ensures full-depth cutting capacity in all materials. -- Ruggedly constructed steel frame for durability and extended machine life. -- The variable speed feed works allow the machine to meet the cutting requirements of different materials. -- Saw head built to precise tolerances assures accuracy for all straight-line ripping operations and provides a stellar quality of cut. -- Top & bottom powered pneumatically tensioned feed rolls for precise feeding and cutting. -- Saw arbor is manufactured from alloy steel for dependability and anti-fatigue, heat treated, precision ground, and balanced providing precise cutting performance.SPECIFICATIONS: -- 8"; Max. Cutting Width -- 5"; Max. Cutting Depth -- 10"; Min. Workpiece Length -- 4"; to 6"; Dia. Top Spindle Sawblade Size -- 8"; to 12"; Dia. Bottom Spindle Sawblade Size -- 6,000 RPM Top & Bottom Moulder Spindle Speed -- 8"; Spindle Length -- 40 mm Rip Saw Arbor Diameter (with key) -- 10 HP Top Rip Saw Motor -- 15 HP Bottom Rip Saw Motor -- 12 to 60 FPM Feeding Speed (Variable) -- 1/2 HP Feed Roll & Top Head Elevating Motor -- 1/2 HP Rip Saw Arbor Elevating Motor -- 3 HP Feed Motor

CAM-WOOD TRS 150F Frame SawCAM-WOOD Frame Saws are engineered and designed to make extremely accurate cuts, cutting products with very tight tolerances up to 0.004" and often eliminating sanding before proceeding to the next step . The unique thin frame saw design accepts different saw frames, blade combinations, and allows multiple saw fence configurations to produce single, double or multiple cuts in a single pass.Specifications: -- 3/4" Min. to 6" max. working width; 1-1/4" min. to 7-3/4" max. working thickness (height); 7-1/2" minimum length; finished material > 0.1094". -- 0.043" to 0.055" Saw blade thickness; runs up to (22) blades at one time at (450) stroke/minute with a 8-1/4" stroke length; accommodates blades 1.575" wide x 19.685" long. -- Saw blade frame is powered by a 15 HP motor. Feed speeds of 1 to 5 FPM by 1 HP motor. -- Features automatic oil lubrication system requiring 90 PSI air pressure. Cooling system via water and air. -- Minimum kerf multi-blade frame saw designed to maximize production and minimize material losses to kerf. -- Machine supplied with PLC controller to allow operator fast, instant set-up changes. -- All controls are centrally located for the operator to easily adjust & control operation. -- Material waste reductions of up to 20% are achievable by use of the thin kerf blades (0.043" ~ 0.055"). -- A special air blast system cools the blade for longer service intervals and removes saw dust from the gullet of the blade to reduce temperature and increase blade life.Note: Frames are available in different configurations.