ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

SALVADOR - SUPERANGLE 600, ...Pusher Chop Saw. Provides complete chop to length & optimization of wood strips, including the elimination of defects. -- Infeed is made of a Heavy-Duty steel frame; working height: 1,000 mm (39") from floor level; safety is provided by a light curtain. -- Pusher slides on double-hardened rails. -- Reading Operation: Uses (2) Sensors: (1) for overall length and the other to read the crayon marks. -- Transmission of power: From motor to the carriage; accomplished by a 50 mm wide steel reinforced toothed belt. -- Part held in place by (2) aligners before & after the blade ensures a square cut. -- Saw box area: Enclosed by interlocking steel cover with a large window for clear view; Saw travels through an aluminum table insert that can be easily changed as needed; High-Efficiency motor, IE3 rating, helps keep power consumption at a minimum. -- Technology: Operating software: Customized Windows-based program; designed to be intuitive and specially designed for optimization of the wood. -- Large 19" monitor at operator eye level; PC set up with SSD Double hard drive with 2nd being a clone to have and be ready to back up in the machine. -- Cut lists: Can be uploaded remotely by network connection or flash drive; chop length optimization can be set for minimum waste priorities. -- Optimizer supports defecting crayons, as well as up to 5-grade qualities. -- Electronics: Multi-tap transformer steps down higher voltages; 460 - 600 to the voltage required by the machine. -- SP 15 Magnetic Strip Measurement: Technology improves positioning from basic encoder standards to absolute measurements of +/- 0.1 mm. -- Outfeed: 0° Belt and (1) PC double ejector. For applications of many workpieces cut at angles, it is best to eject the workpieces together with one large rack & pinion ejector. Workpieces are pulled from the Saw on an outfeed belt. - Once the parts are clear of the Saw, the large ejector manages all cuts in 1-push onto the steel table for collection. WORKING CAPACITYMaximum board length before cutting: 5,100 mm (16').Minimum board length before cutting: 500 mm (19.6").TECHNICAL SPECIFICATIONSMain saw power: 15 HP.Saw blade specifications: SA600; Max. 00 mm; dia. bore 35 mm.Maximum pusher reading speed: 60 MPM (200 FPM)Maximum pusher pushing speed 60 MPM (200 FPM)CUTTING CROSS SECTION 0°: 100 mm x 360 mm / 160 mm x 310 mm. +/- 45°: 100 mm x 260 mm / 160 mm / 220 mm. +/- 70°: 100 mm x 120 mm / 160 mm x 100 mm.Minimum: 15 mm x 30 mm.Number of cuts within last 40 mm of board One: (1)Maximum workpiece weight: 110 kG (242 Lbs).Power Requirements 11 kW. Primary supply voltages: 220/380/420/440/460/480/560/580/600 V.Pneumatic Requirements Compressed air supply: 600 - 800 kPa (6 - 8 bar). Maximum air consumption: 300 Nl/min.Dust Extraction Intake diameter: 160 mm Upper; 120 mm lower/ Extraction System Collection speed: 28 M/s. Dust Extraction Capaci

SANDMAN DL7236 Downdraft Sanding Table;The SANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench. -- 72" X 36" Rubberized work surface. -- 1.5 HP T.E.F.C. 220V 1-Phase motor with 10-5/8" LAU blower with sealed ball bearings. -- Industrial casters with 4" wheels, (2) ridged, (2) swivel-lock 2-ways. -- Hinged tilt-up top with gas strut lid support for easy filter servicing. -- Adjustable in height from 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu. Ft. of built in storage area with 1 pull out shelf. -- 18 Months Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN DL7236 Downdraft Sanding TableSANDMAN Sanding Table is a dedicated sanding station that doubles as a workbench.Specifications: -- 72" x 36" Rubberized work surface. -- 1.5 HP T.E.F.C. - 220 V - 1-Phase motor with: 10-5/8" LAU Blower with sealed ball bearings. -- Industrial casters with: 4" Wheels: (2) Ridged; (2) swivel-lock 2-ways. -- Magnetic tool holder. -- Hinged tilt up top with: Gas strut lid support for easy filter servicing. -- Adjustable in height from: 34" - 38". -- Grid system top adds versatility. -- 10.4 Cu./ft. of built-in storage area with: 1 Pull out shelf. -- Easy filter service.

SANDMAN DL9648 Downdraft Sanding TableThe DL9648 is a dedicated 96" x 48" sanding table that doubles as a workbench. The Sand Pro DL9648 is perfect for sanding large pieces such as doors or as a multi-person sanding station. Specifications: -- Table height 36", table size 96" x 48". -- (2) 1.5 HP TEFC motors with 7,400 CFM @ 1.5 SP and (2) 16" backward inclined fans. -- (6) Extended surface pleated filters each 20" x 25" x 2" deep w/ 1/2" netted polyester filter. Features: -- (4) 110 V duplex receptacles. -- Rubberized mar-proof top. -- Grid system top for jigs and fixtures. -- Hinged top with gas strut lid support for easy access to filters. -- (2) 10" x 32" Shelves. (2) 18" x 24" Storage drawers. -- Stainless steel hanger for air orbital sanders (choose 5" or 6"). Options: -- 3" Swivel casters (Adds 3/4" to machine height). -- Case of (12) replacement filters. -- Single phase available -- 18 Month Limited WarrantyNOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.

SANDMAN M74836 Downdraft Sanding TableGreat sanding table for a singular function such as doing cabinet doors, door fronts, etc. This downdraft table has a 6″ overhang on the front side making it good for sanding while sitting. Machine comes standard with casters, utility tray, & Felt-lined Platforms.Specifications: 48 L x 36" W top surface with heights of 32", 34" $ 36". -- Overhangs of 6" front. 0" back and 4" ends. -- (2) DP20252 Filters and (1) PF4029 pre-filter. -- 1 HP Baldor Motor – Standard Single Phase 110V (13 Amps) -- (18) Month warranty on parts.(Single and 3-Ph 220V available)NOT IN STOCK - CALL OR EMAIL FOR CURRENT LEAD TIME TO SHIP. PRICING SUBJECT TO CONFIRMATION.