CAM-WOOD AC-100120 Piston Air CompressorHeavy Duty unit with a 10 HP induction motor.Features & Specifications: -- 34.2 CFM @ 90 PSI, Splash lubricated cast iron 2-stage pump. -- Automatic start/stop operation. -- 120-Gal. horizontal tank that meets the ASME standards. -- Manual tank drain & pressure gauge. -- Deep finned after-cooler. -- Fully enclosed belt guard and ON/OFF pressure switch. -- Deep finned cylinder head for cooling and replaceable air filter/silencer. -- Durable painted finish for years of service under the worst conditions.

CAM-WOOD DC-102 Dust CollectorSmall radial-finned Dust Collector mounted on wheels for portability.Features & Specifications: -- Large 13-1/2" fan that produces 2,100 CFM. -- Heavy Duty 3 HP motor pre-wired at 230 Volts. -- Large capacity dual station cloth top bags of 31.2 sq. ft. total cloth filter area. -- Low sound level of 75 - 90 dB.

CEFLA ROCTRE D Automatic Spray Finishing Machine for HIGH VOLUME PRODUCTION and includes (2) two integrated cleaning trolleysThickness: Max. 50 mm (2"); Min. 5 mm (0.2").Maximum Line speed: 20 MPM (65 FMP).Equipment Specifications:CEFLA, model ROC 3 D. Is a Two-arm reciprocating Spray Machine: -- Parts are fed under the Part Reading Bar to measure size and spray parameters on a continuous CFB belt conveying system. -- Lacquer recovery and belt cleaning are accomplished by means of a "cleaning trolley" located under the existing end feed belt. Made up of counter-rotating rollers with scraper and belt cleaning unit, with (3) rollers and stainless-steel troughs: all the rollers are fitted on the motorized trolley longitudinally removable by hand pulling of trolley out. -- Powered outfeed tilt-able belt lifts to approach the cleaning trolley. -- (2) Oscillating arms equipped to accept a maximum of (8) guns, four per arm, and driven by a Brushless servo motor.There are (2) Separate lacquer feeding circuits with recycling system. -- This is a fully pressurized spray cabin with an exhaust air filtering system for overspray using a double dry filter set, primary filter, and secondary. -- Electronic control cabinet to monitor spraying functions.The booth consists of sandwich paneling, and air is pushed in through (2) air intake ducts (positioned between guns) above the slanted perforated top panels made of fine filter material, which help to reduce turbulence. Parts running through the sprayer can be viewed by means of a large front viewing window/access panel, which can be lifted to access the guns and interior of the sprayer. Photos show equipment while it was still in service - currently being reconditioned.Note: EX-FACTORY’s Logistics Department is experienced and set up to provide “Full Service Logistics"; from Overseas Suppliers to your Door. …Packaging, Container Loading, Ocean Freight, Marine Insurance (door to door).

CEHISA PRO 10 .EDGEBANDER (W/PREMILL): -- Features: Pre-milling Station with: 2 x 1.5 kW (2.0 HP) 12,000 RPM motors; standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System: 10 - 15 Min. heat up time, auto-temperature drop. Glue Tank is coated with nonstick material, quick change mechanism for easy maintenance and/or color change. -- Pressure Section: (1) Large dia. driven and (2) idle rollers. Digital readout and pneumatic positioning selectable from controller touchscreen. -- Edgebanding Workstations. End Trimming Station: Double motor front & rear, 2 x 0.35 kW (0.5 HP) - 12,000 RPM. -- Edge Trimming Station: Top & bottom flush/bevel/radius trimming, (2) 0.35 kW (0.5 HP) - 12,000 RPM motors, tiltable 0° - 20°, pneumatic exclusion from operator panel. -- Profile Scraping Unit: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper: To remove potential glue squeeze out. -- Buffing Unit: Top/Bottom, (2) 0.12 kW (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Controller: "Unitronics V350" Controller with color touchscreen, memory up to (20) programs. -- Equipped with: Feed Speed: 9 & 14 MPM (29 & 46 FPM). -- Power hold-down beam, workpiece support outrigger, safety & sound enclosure. -- Included Options:RIEPE non-stick Spray System. -- Actual Model is: CEHISA PRO 10

CEHISA - PRO-9, ...Edgebander Single-Phase Electrical!Single-sided Edgebander with: End trim; top/bottom trimming; scraping; buffing.Specifications: -- 0.4 - 3 mm Edge thickness cap., -- Teflon coated glue pot system. -- Automatic magazine for strip & coil feed; Heavy-Duty guillotine for up to 3 mm thick PVC. -- (2) roll pressure zone with (1) motorized and (1) idle roller. Workstations: -- Double-motor end trim station; 0.33 HP - 12,000 RPM ea. motor. -- Top & bottom flush/bevel trim; bevels 0° - 20°; 0.45 HP ea. motor. -- Top & bottom PVC profile scraper; up to 3 mm radius. -- Last Station: Top & bottom buffing unit; 3/4 HP motors. -- Electronic braking on trim motors; digital readout on top/bottom trim. -- Feed speed: 33 FPM & 1 HP feed drive. -- Sound enclosure. -- Outboard panel support. -- Frequency converter. -- Digital readouts for trimmer adjustments. -- Sound enclosure.

CEHISA PRO-12 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Features: Pre-Milling Station with:2 x 1.5 Kw (2.0 HP) 12,000 RPM motors, standard equipped with diamond cutters. Both spindles pneumatically controlled. -- Spray agent unit for top and bottom with (2) sprayer and (2) reservoir -- Automatic Edge Magazine: For coiled material up to 3 mm thickness, strip feed magazine for up to 5 mm (3/16") solid wood banding. -- Quick Melt Glue System, MR-5:10 - 15 min. heat-up time, auto temperature drop. Glue Tank is coated with nonstick material, quick-change mechanism for easy maintenance and/or color change. -- Pressure Section:(1) Large dia. driven and (2) idle rollers. Digital read-out and pneumatic positioning selectable from controller touch screen.Edgebanding Workstations: -- End Trimming Station, V-7: Double motor front & rear, 2 x 0.35 Kw (0.5 HP) - 12,000 RPM. -- Edge Trimming Station, BC-5: Top & bottom flush/bevel/radius trimming, 2 x 0.55 Kw (0.75 HP) - 12,000 RPM, tiltable 0° - 10°, pneumatic exclusion from operator panel. -- Corner Rounding Unit, FD-50: To process overhanging edges and trimming around the leading & trailing edge, 1 x 0.27 Kw (0.36 HP). -- Profile Scraping Unit, R-8: For thick PVC/ABS radius scraping, pneumatic in/out positioning from control panel with chip collection box. -- Flat Glue Scraper, RR-7: To remove potential glue squeeze-out. -- Buffing Unit, PC-9: with spry mist unit top/bottom Top/Bottom, 2 x 0.12 Kw (1/8 HP) - 1,650 RPM motors, tilting horizontally and vertically. -- Operator Interface:PLC Microprocessor control with color touch screen, memory up to 20 programs.Equipped With:Feed Speed, 9 - 14 MPM (29' to 45 FPM), -- Power hold-down beam, work-piece support outrigger, safety & sound enclosure. Included Options:Riepe, non-stick spray system. -- Nesting Tracer Shoes for top/bottom trimmers

CEHISA EP-7 EDGEBANDER1/4" Cap. edge thickness; min. panel size: length 4-3/4", width 3" and thickness 3/8", unlimited length & width; PLC controlled operation.Equipped with: -- Automatic strip feed & coil feed magazine, compact Hot Melt glue system, heats up in (7 - 10) Min, optional Heavy Duty guillotine for 3 mm thick PVC, 3-roll pressure section. Work Stations: -- Single motor end trim (0.3 HP), motor tilts 0° - 10° -- Top & bottom flush & bevel trim unit (0.75 HP ea. motor), tilts 0° - 20° -- Feed speeds of 33 FPM and a 1 HP feed drive.Complete with: Digital counters, sound enclosure, frequency inverter, telescoping outboard panel support & used tooling.

CEMCO 2000 Wide Belt Drum Sander, Single Head. --Specifications: Lightly used. Only 2180 Hours. -- Belt Size is 37" X 75"; 20 HP main motor,.1.5" top roller plus 2- 5" bottom rollers. One steel 1 rubber covered. -- Thickness is from 0" - 6". No Platen. Variable speed feed. Emergency brake. good. 4-1/2" dust port. -- Note: This machine was replaced 12 years ago with a triple head Cemco. Stored in a dry warehouse since then. Ran well until we unplugged it. All Cemco equipment is of commercial quality. This sander is a workhorse.

CEMCO - 4000, ...2-Head Wide Belt Sander38" Width cap. - Drum, Platen configuration.Head Configuration:1st Head: 40 HP -1,780 RPM rubber contact drum head.2nd Head: 30 HP - 1,775 RPM platen style head.Specifications: -- 3 HP 230/460/60/3 Feed motor with TOSHIBA VFD controls. -- 15 - 60 FPM Conveyor feed speed . -- 30 HP - 3,525 RPM Vacuum blower. -- Vacuum type rubber conveyor feed belt. -- Push button controls and amp meters. -- Electric ProScale digital thickness readout. -- YASKAWA Varispeed F7.Equipped with & Features: -- VFD abrasive belt drive system. -- Outfeed workpiece dust cleaning enclosure.Includes: Replacement abrasive belts and belt racks.

CEMCO SBV-120 Vertical Boring MachineSpecifications: -- 113" x 22" boring area Capacity, (14) 1.5 HP - 1,800 RPM motors driving (14) spindles, on/off switch controls for all motors -- Spindle nose with chuck 5/65" - 1/2" capacity -- 121" x 30.5" table size, (4) Spring loaded hold downs, -- 6" Spindle stroke adjustment with min. of 4" to max. of 10" between spindle nose and tabletop. -- Spindle assemblies advance hydraulically at 0 - 30 strokes/Min with single or continuous stroke -- 2 HP hydraulic feed pump w/variable speed control.Also included: -- 4 CHIP BLOW OFFS WITH INDIVIDUAL ON/OFF POSITIONS -- INSTRUCTION MANUAL/PARTS LIST -- DRILLING SAFETY GUARDS -- EMERGENGY STOP CABLE AND EMERGENCY STOP BUTTONFLOOR SPACE FOOT PRINT: 48: X 121"

CEMCO MBV 54 Vertical Boring Machine54" x 15" Cast iron table with wooden top,Equipped With:(2) Universal spindles with movable spindle supports,(3) 2 HP - 1,725 RPM direct drive spindle motors,36" Stationary table height; 6" Max. vertical stroke, spindles advance hydraulically at 0 - 30 strokes/Min;Foot pedal actuated w/single cycle & continuous automatic modes;2 HP hydraulic feed pump, 12-gal. hydraulic pump system;Note: Riggers are required for loading

CEMCO UF-37-1-103 SINGLE HEAD WIDE BELT SANDERSingle head Wide Belt Sander with 36" wide capacity; combination head with 6-1/8" diameter contact roll & independently adjustable platen. Equipped with: -- 30 HP main motor; 1 HP variable speed conveyor feed 30 to 50 FPM; and 1.5 HP Power Raising and Lowering Conveyor Bed Motor with hand wheel fine adjustment.. -- 37" x 103" abrasive belt size; -- Electric eye tracking. -- Single infeed and outfeed hold down rolls and Anti kickback finger devise on the infeed of the Sander, -- Load meter, disc brake on sanding head, and magnetic controls. Recently replace conveyor belt, Contact Sanding Roll and bearings.OVER BUILT for heavy loads. Grerat Sander for SLAB material.No longer required for ongoing operations.

CEMCO 1237 DUAL HEAD WIDE BELT SANDER2-Head, 36" cap. - 1st Head: Rubber covered contact roll, 20 HP motor; 2nd Head: Finishing platen, 15HP motor; 37" x 75" abrasive belts with air tensioning. -- Variable speed conveyor feed, 15 - 60 FPM, 0" - 6" thickness cap., infeed & outfeed rubber covered pinch rollers. -- Equipped with: Motor load meters, infeed conveyor extension, air disc brakes on sanding heads, emergency operator stop bar, and dust hoods. Actual model # "1237-SE".Seller recently upgrades to a 3-Head 52" wide Sander and this one is no longer needed

CENTAURO AG-125 Tool Grinding Machine for V-Type Gouges. -- Tabletop design saves space. -- Works with most sizes of V-gouges. -- Optional standing base $414.00. -- Diamond stone cutting wheels, ordered separately, price $636.00 each. -- Please specify the required voltage and lathe model when ordering wheels.

CENTAURO TC-1200 Copy Lathe;47-1/4" Max. between centers. -- 4-3/4" Height of centers over bed. -- Max. copy dia. 6" (4-1/8"). -- Max. dia. permitted by traveling steady 3-1/2" (2-1/2"). -- 4 HP main motor, 900 - 1,500 - 2,200 & 3,540 RPM spindle speeds. -- 1 HP hydraulic variable speed carriage with tool post and revolving steady rest. -- (2) Independent gouges working in conjunction with the traveling steady rest. -- Variable speed hydraulic saddle movement. Standard Equipment & Specs: -- Drive center with (2) interchangeable heads 1" and 1-3/4". -- Tailstock revolving center 1/2". -- Traveling steady rest max. 3-1/2" (square 2-1/2" x 2-1/2") with reduction bushing. -- (2) Vertical Tantung gouges, radius 1.2 mm and (1) precutting tool. -- Work-piece centering device. -- Tool support rest for hand turning. -- (2) Dust extraction ports 4" dia. -- Motor protection switch. -- Emergency push button. -- Front sliding safety guard. -- Standard: Service tool kit and Abrasive stone for cutting edge dressing.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with two copier heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and revolving steady rest attachment; 3-1/2" max. square part size with revolving steady rest, unit, 5.8" stroke of copying unit. 19-5/8" max. length for manual turning. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. -- Includes: Drive center, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center. -- Note this machine has no top Back Knife for plunging with form tool. -- Machine manual included.

CENTAURO T5-1600 Hydraulic Copy Lathe with (2) top plunging knives; Specifications: -- 63" (1,600 mm) Max. between centers, 4/5.5 HP main motor, two speed selector switch, 900 - 1,500 - 1,800 - 2,250 - 3,000 and 4,500 RPM spindle speeds. -- 1 HP Hydraulic power pack for variable speed carriage 0 - 19 FPM carriage; return speed 24 FPM, hydraulic tailstock with Pressure Reducing Valve (PRV) for fine control of pressure, especially helpful for small and/or slender turnings. Equipped with: -- (2) Independent copying units, (1) for roughing and (1) for finish cutting. 1st, 2nd pass & auto feature with 2nd pass active it will cut the pattern 2 times automatically and sequence the tools between cuts. -- Revolving steady rest, max. dia. 140/100 mm square ( 5.5"/3.9"), and for max. dia. 90/65 mm max. square billet size. -- 9.8" (250mm) Max copy dia., 6.8" (175 mm) Max. square section without steady rest.. Includes: -- (2) rear-top plunging slides manually operated with knives for making dowel ends; 45/26 mm drive center for headstock and 12 mm center for tailstock, (2) V-type gouges with 0.6 & 3.5 mm cut radii.Features: Centauro AG-125 Knife Sharpener.NOTE: Ex-Factory handles import/export to just about any country in the world.

CENTAURO T5E -1600 Semi-Automatic Hydraulic Copy Lathe with (2) Copier Heads. -- General data: 63" (1600 mm) Max. between centers and 8-5/16" height of center over the bed, 5.5 HP main motor with saddle advance using a lead screw with precision recirculating balls for max. accuracy.Automatic work cycle sequencing with electronic control capable of up to (5) different programmable cycles. -- Drives/Controller: Programmable saddle with variable feed speed; 900 - 1,500 - 1,800 - 2,250 - 3,000 & 4,500 RPM spindle speeds; 1.5 HP hydraulic variable speed carriage, 0 - 39-1/2 FPM, carriage return speed 39-1/2 FPM. CENTAURO "EM-12" Programmable Controller. -- Equipped with: (2) Hydraulic tracing units and attachment for revolving steady rest; 3-1/2" max. square part size with revolving steady rest, 5" max. with copying unit, 5.8" stroke of copying unit. -- Capacity: 19-5/8" Max. length for manual turning. 9.8" (250 mm) Max copy dia., 6.8" (175 mm) max. square section without steady rest. -- Includes: Drive center with, revolving tailstock center with 12 mm dia. tip, and automatic double pass system for finishing center.Note this machine has no top Back Knife for plunging with a form tool.

CHAMPION - HRA25-25, ...Dual Stage Air Compressor. 25 HP Commercial Duty motor; 90.1 CFM at 175 PSI and 250-gal. horizontal tank. -- Features: CHAMPION's "R" Series 2-stage cast iron pump, dome pistons, and disc valves allow for higher performance at lower RPM's; largest roller bearings in the industry. -- The 250-gal. horizontal tank is equipped with: Large pressure gauge, standard tank drain, and a hard painted finish for years of durability. -- Complete with: Large dia. air filters, OSHA approved belt guard. -- Air-cooled aftercooler.

CHEN SAN FUNG SD-100 Denibbing Sander --39" Width cap.; (1) head with (6) 0.5 HP counter rotating arbors mounted on a central rotating drive assembly with (20) blades per spindle, variable assembly rotation from 2 - 20 RPM. -- Each arbor/spindle is equipped with abrasive fladder disc type brush media, variable arbor speed from 300 - 1,200 RPM. -- Conveyor belt feed with vacuum holdown, variable feed speed from 6 to 39 FPM with 2 HP drive. -- Infeed & outfeed holddown pinch rolls, 0" to 4" motorized part thickness with working width from 6" to 39" part size opening with mechanical readout. -- Complete with: Controls on belt loading side, RPM readouts for spindle speed, magnetic starters, 7" dust collection outlet and optional 15 HP vacuum turbine motor.