ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

GLOBAL BAGGER SYSTEMSpecifications: -- Support Structure 2" Tubular Steel -- Height 86 Inches -- Length 12 Feet -- Width top 60" and 90" Base -- Total Weight 1900 Lbs approx. -- Hopper Width 60" -- Hopper Length 106" -- Hopper Depth 44 " -- Capacity 3 Cu.Yards -- Hopper Conveyor Length 146 " -- Hopper Conveyor Width 25" -- Rubber Conveyor Belt 18" Wide -- Bag Clamp Air Operated -- Heat Sealer 24" capacity -- Bagging Capacity up to (200) Bags per HourOptions available, but not included; -- Weight Measure Scale -- Air Compressor -- Bag Stitching Machine -- One Year Warranty -- Loaded on your Truck

GOLD STAR STARPRO AG 510 CNC ROUTER W/ATC & BORING: -- Specifications:5' x 10' FLAT TABLE CNC ROUTER W/ATC & BORING is great for "Nested Base Manufacturing" or just about any type of 3-Axis work. -- Working Table: 63" (1,600 mm) x 122" (3,100 mm). There are (5) sets of pop-up stops to aid in panel positioning & a 6-zone vacuum table system. -- X- & Y-Axis speed are 3,181 IPM (265 FPM / 83 MPM) and Z-axis is 350 IPM (29 FPM / 12 MPM) for quick traverse positioning that reduces total CNC machining time between cutting cycles. (3) AC 750w servo drives power the axes movement. -- Industrial machine tool welded structurally engineered machine base provides a solid foundation for superior cut quality, the entire frame is stress relieved and heat treated. -- The moving gantry bridge travels on large thick hardened & precision ground rectangle linear guide slider-ways giving extra smooth movement for high speed traverse and accurate cutting. -- Tool gantry & bridge movement by large thick inclined teeth rack & pinion; the vertical axis travels on a large dia precision ball screw for smooth consistent movement. -- Boring Unit: (1) 9-Spindle Vertical Boring Block with 5 independent spindles in "X" axis & 4 independent spindles in "Y" axis. -- Machining: (1) 12 HP (8.9 kW) Air cooled Router spindle with HSK 63F adaptor, variable programming speeds from 1,000 to 22,000 RPM. -- Tools are loaded into the spindle by (1) 8-position ATC Rack mounted at the end of the machine base. -- Tool heights can be set using the Tool Length setting gauge (included); machine requires ER-32 tool collets. -- CNC Control: Industrial grade OPEN CNC control with color monitor; includes self-diagnosis & alarm history display & background editing; up to (4) simultaneously controlled axes with 3D simulation, helical interpolation, tool offset, length compensation & backlash compensation. -- Compatible with virtually all CAD/CAM programming software on the market; You choose the software that best suits your needs. -- Complete With: (1) 15 HP (11 kW) "Rotary Vane" dry-type vacuum pump. -- Complete with: Dust hood with 6" manifold connection; Tool Length setting gauge; "MPG" hand held wheel remote; Safety bumper system on both sides of the moving bridge & a safety bar around the back of the machine.

Gomad "DFDA-455" Sliding Table Single Spindle Shaper -- Specifications: 2-1/64" (55 mm) spindle currently, 7.5 HP belt drive motor, (4) speeds 4,000/6,000/8,000 & 10,000 RPM, 3-9/16" spindle travel, 3/4" up to 2-11/64" dia. interchangeable spindle, reversing spindle rotation; heavy duty 36" x 40" cast iron table, (3) pneumatic clamps, double end fence, 4.5" dia. dust chute. -- Complete with: 13" wide sliding table, (4) Hold down springs, mounting collars & bolts, miter gauge with stop rod, and foot brake, capable of doing arch molding work.NOTE: Don't go too much by the appearance. In running condition before disconnect in 2013, currently stored in the facility's basement.

GOODSPEED HF 412 AO Vertical Oscillating Chair Back Sander Specifications: Table size 30” x 30” x 34-1/4” H. Equipped with: 12" W x 25" L Horizontal abrasive belt, with 12” H x 4” Dia. Aluminum & Spiral rubber drums, 12” H x 3-1/2” Dia. Spiral rubber feed drum, with 2 HP Motor & Variable feed speed control. 60 W Feed & Oscillation motors.

GOODSPEED FH30 Semi-Automatic Copy Lathe. Specifications: --30" Cap. with a 3" max. dia., hopper feed for square or round stock, 15 HP main spindle motor for 2,250 - 3,200 - 3,825 & 4,625 RPM; reciprocating tail spindle. -- 2 HP Hydraulic feed on back knife; up to (900) pieces/Hr capacity. -- Complete with: Carriage slow down control system, pressure lubrication die system, 2-belt head spindle drive, and adjustable knife bar for cutting tapers. -- Includes: Pneumatic steady rest; Custom pressure reducer; used tooling and extras. -- Original manual included. -- Was used for making drumsticks.

INTOREX TXA-1200 Automatic Hydraulic Copy Lathe;Specifications: -- 1,200 mm (47-1/4") Max. turning length, 210 mm (8-1/4") max. turning diameter. -- Max. turning dia. with standard steady 90 mm (3.5"). -- (2) Hydraulic copiers. -- Max. size of square stock for turning with automatic feed 100 mm (3.9"). -- (3) Tool holder turrets. Hopper feed unit. -- (8) Head speeds in a range from 750 - 5,500 RPM. -- 6 HP or 7.5 HP Headstock spindle motor. -- 4 HP Hydraulic pump motor.

GRANUTECH-SATURN - BIG MAC, ...Used Car Crusher471 Detroit Diesel EngineSpecifications: -- Widely recognized as the industry standard, "Big MAC" flatteners combine high performance and low maintenance characteristics in a mobile auto crusher. The result is an unparalleled record for equipment performance: more than 90% of all "Big MAC" flatteners ever made are still at work, with machines built in the 70’s still in operation today. -- Featuring Heavy-Duty “quick-set-up"; hydraulic cylinders that can be quickly and easily raised for operation or lowered for travel, the "Big MAC" flattener meets the needs of today's mobile scrap processor. Offering a wide, opening for easier loading and larger capacities, the "Big MAC" is built to perform. Multiple automobiles can be easily compacted into dense bundles, reducing both onsite storage demands and transportation costs.Key features and benefits include: -- Quick setup design -- Air Compressor -- Waste oil collection tanks -- 6-Cylinder Tier III engine -- 6" Cylinder rods -- Hydraulic landing gear -- Heavy-Duty push bumper

GRANUTECH-SATURN - 62-40, ...Dual Shaft ShredderSpecifications: -- Motors: (2) 100 HP. -- Feed Opening: 62" x 40". -- Dual Shaft with independent Driven Shafts -- Includes: Feed conveyor & discharge conveyor, extra feed hopper; an extra pulley roller that is magnetized for exit end of discharge conveyor (current pulley roller in use is nonmagnetic). -- includes: (2) Service manuals and catwalk structure.

GRANUTECH-SATURN - GRIZZLY 80, ...Grinder Granulator NO MOTOR, LID OR DRIVE TRAINSpecifications: -- Rotor size: 77-1/2" -- Cutting diameter: 34-1/2" -- Main motor: 300 HP -- Speed: 321 RPM -- Number of knives: 50 -- Number of stationary knives: 10 -- Rotor type: STAR

GRASS - RAM, ...Drawer PressPneumatic Drawer Press used for pressing & inserting the GRASS SARGEN slide. -- Tabletop mount, foot pedal activation. -- NOTE: Machine is shown "as it is". Additional aluminum base frame was NOT shipped with this machine.

GRASS - ECOPRESS P: Boring Machine (Hinge) -- SpecificationsPneumatic tabletop unit mounted on welded frame base; hinge boring w/GRASS inserter block.(1) 3-Spindle boring head for hinges; 1 HP motor. -- Drill unit & insertion head and (2) spring loaded holddown cylinders operate pneumatically. Boring depth automatically sets to the material thickness being processed. -- Complete with: &#9679 450 x 730 mm Extruded aluminum framework table.&#9679 LH & RH material side stops. -- Actual Model: GRASS ECOPRESS P

GRECON PJ 150/500 and PF 10-610 Finger Jointer and PressFinger jointer and Press systemSpecifications: -- Grecon Finger Joint System Including: Model PJ 150/500 Shaper -- Trim Saw 5 HP -- Shaper Head 30 HP -- Glue Application Head -- Timber Width 30 mm - 159 mm (1.2" - 6.25") -- Timber Thickness 12 mm - 80 mm (.5" - 3.15") -- Timber Length 250 mm - 1780 mm (9.84" - 70") -- Infeed Belt Conveyor 20" Wide X 34" LongAfter the Finger joint shaper: -- Manual Roll Conveyor with Rotation for Turning Workpieces 22" X 68" -- Outfeed Belt Conveyor 20" X 39" -- Driven Roll Conveyor 20" X 120" -- Powered Belt Conveyor Prior to Press 7" X 86"Model Press PJ 10/6100 Finger Joint Assembly Press: -- Maximum Pressing Length 240" -- Cut-Off Saw Motor 3HPNote: The machine will be reconditioned upon placement of order.

GREENMAX - EPS-AC-100, ...Cold Press DensifierSpecifications: -- EPS Polystyrene Foam Densifier -- Ratio: 50 to 1 -- Volume: 220 Lbs/Hr -- No Conveyor -- Loaded ont your Truck

GRIGGIO SC-1500 Table Saw Specifications: -- 60" Cut cap.; 5 HP main motor & scoring motor with 3/4" dia. arbor and 9,000 RPM blade speed; external scoring blade adjustment. -- Features: -- 0° - 45° Tilting 1" dia. main saw arbor, 16" max. blade size, 5.1" max. depth of cut, single blade speed. -- Rip-cut fence assembly adjustable to 60" max.NOTE: Dimensions and weight are approximate.

GRIGGIO G 1100 Wide belt Sander2-Head, 1,100 mm (43") width cap. -- 1st Head: Rubber covered steel contact roll, duro 85, 220 mm diameter . -- 2nd Head: Rubber covered contact roll duro 50 -- 25 HP motor to drive both head. -- 43" x 85" abrasive belts, electropneumatic abrasive belt tracking, -- Conveyor belt feed, two speed from control panel at 15 and 30 FPM, 0.4/0.7 HP feed drive, automatic conveyor belt tracking, -- 1/8" - 6-1/2" motorized thickness adjustment with LED readout & 0.75Hp gearmotor drive. --Automatic positioning of the working table, rubber covered spring loaded pressure rollers, double infeed and outfeed rubber covered rolls, infeed panel "over-thickness" sensor. --Two suction dust hoods dia. 6" (150mm),

GRIZZLY H2934 2-HEAD WIDE BELT SANDER2-Head Wide Belt Sander, 36-1/2" width cap. -- Head configuration: - 1st Head: Rubber covered contact drum; 2nd Head: Combination head with rubber covered contact drum and adjustable platen; Abrasive belt size 37" x 60". -- 0" to 6" Thickness cap., LED digital depth encoder; 14" min. board length and 12" infeed conveyor. -- 1st Abrasive belt surface speed of 3,543 SFPM; 2nd abrasives belt surface speed of 2,554 SFPM. -- Conveyor speed from 14 - 60 FPM. -- 20 HP - 50/25 Amp Sanding motor; 1 HP - 3.4/1.7 Amp conveyor motor; 0.25 HP - 1.2/0.6 Amp table lift motor. -- Complete with: Rubber covered holddown rolls, adjustable felt platen, Amp/load meter, and disc brake for emergency stop.

GRIZZLY - G1026, ...Single Speed Shaper w/Feeder & Mobile Base3 HP - 3,450 RPM Motor; 1/2", 3/4" & 1" dia. interchangeable spindles; 2-1/2" spindle cap. under the nut and with 3" spindle travel. -- (2) Spindle speeds of 7,000 or 10,000 RPM; reversing spindle switch. -- Features: 28-1/4" x 21-3/4" table; 34" table height.Complete with: Magnetic spindle brake, adjustable fence & 3" dia. dust extraction outlet.3-Roll 4-Speed Power Feeder & Mobile Base!

15" Width cap. with 1/4" - 8" thickness opening, 1/16" max. depth of cut; 3 HP single-phase motor belt drives 3-knife, 3-15/64" dia. cutter-head at 5,000 RPM; head with high-speed steel knives, max. thickness 8", min. 3/16"; dual feed speed of either 16 or 30 FPM; 16" x 42" cast iron table, table extensions on infeed/outfeed. Complete with: Magnetic controls, 2" dia. metal infeed & outfeed rollers, open fabricated steel base, and large hand wheel for cutter-head assembly adjustment.