MARCUS TRANSFORMER 15 KVA, 3-Ph, Auto, 600/480 V Transformer with tap for 440 V.15 KVA Auto-ventilated "dry type" transformer 600 V in (primary); 480 V out (secondary) with tap on secondary for 440V at full capacity. -- Manufactured with grain oriented silicon steel is used. -- Coil windings with high quality magnet wire and the enclosure is made of heavy gauge steel w/ventilation openings. -- UL and CSA approved.

--In auction: https://exfactoryauctions.com/Detail/SH-230492/event/A122024$1 --NO RESERVE!-- MARTIN T 23 Tilting Spindle Shaper, with 30 mm (1.18") Interchangeable Spindle & Power Feeder Specifications: Table size 940 x 1100 x 850 mm (37.01” x 43.31” x 33.46”) H, with Table insert dia. 90, 130, 205, 305, & 480 (3.54”, 5.12", 8.07”, 12.01”, & 18.90”). Spindle tilt 0° to 45°. Maximum capacity under nut 7". Vertical spindle adjustment 145 mm (5.71"). Spindle speeds 3000, 4,500, 6,000, & 90,000 RPM. Equipped with: 6.4/7.8 HP Motor. "MK5" Spindle shaft. Mechanical spindle brake, with Foot pedal. Hand spindle lock. Complete with: 11-1/2” x 4-3/4” Left & Right Fences, with 21” x 6” H Left & Right Wood fences. 1996 CO-MATIC 1 HP 4-Speed 4-Roll Power Feeder, with Speeds 13, 26, 26, & 72 FPM. Dimensions with Power Feeder: 42" x 42" x 63” H.

MARUNAKA Model RD – 8J WIDE Single Deck Veneer Roll Dryer;Complete with the following features: -- 1988 - year of manufacture. --Working width – 51"; --Length of the dryer – 24 Ft (4 Sections) --Type of heating - Steam --Operational in 2018 when mill closed --Professional rigging and loading available.

MARUNAKA Model RD-3UB/RD-6UB (Connected) Single Deck Veneer Roll Dryer;Complete with the following features: -- (3) 3 HP circulating fans with (1) 3 HP exhaust blower thru the ceiling. -- Optional heat source: electric (7) Elements/Zones, computer controlled thermocouples in addition to (2) Natural gas burners (OEM).. Both dryers have a 100amp circuit breaker with 100amp fuses. The RD 8 operates with 4 fan motors and 4 heaters. The RD 6 has 3 fan motors and 3 heaters";.. -- Capable of temperatures to 120° Celsius (250° Fahrenheit). -- Working width 1000 mm or about 39 inches. Veneer is fed endo.Please Note: -- Dryer is (2) separate units; all equipment will fit into a 40' container for shipment from Eastern USA. -- All equipment is in good working condition including all fans and blower, temperature control works properly; feed roll drive works well. -- Rolls have been nickel treated to minimize corrosion/oxidation. -- This dryer equipment is still in place. -- MARUNAKA (2) Models: RD-3UB and RD-6UB currently connected to increase capacity. Can easily be separated.NOTE: Refurbished in 2005, operated from 2005 - 2012. Still operational ready to work!

MASTER MACHINERY MC-MDS-1 Single Spindle ShaperSpecifications: -- Table size: 27.5" x 32" -- Spindle speed: 7500 - 10,000 RPM -- Main motor: 3 HP

MASTERWOOD OMB1CN3-TF Horizontal Slot Mortiser. One NC working head (3) axis with a programmable microprocessor. Machines a sequence of slots on windows, doors, shutters, or cabinets without moving the workpiece. Continuous cycles with loading/unloading. -- Equipped with: (1) MAKA style chisel mortising unit, (1) Vertical routing unit, and (1) TF Horizontal routing unit. High-frequency drilling - routing with controlled axis, DC motors, and ball screw is driven. -- Max Mortise workpiece size 150x110x2800 mm length (5.9"x4.3"x110.2"). Vertical and horizontal routers 142"; length. -- Max slot depth 130 mm (5.1"). Max vertical head stroke 140 mm (5.5"). -- Features: Pneumatic hold-downs bar mounted above table. Flip-up pneumatic pressure beam for additional support when needed. Free-standing control and electrical cabinets house computer monitor and keyboard. Master universal electronic system controller (MW CN10 Centromac) -- Vertical routing assembly: 4HP, 220/380v 3 PH, 9,000 RPM -- Horizontal routing assembly 5"; 220/380v, 3 PH, 9,000 RPM -- Memory for 50 cycles. Mirror imaging with preset tool speed (over-writeable knob). -- Total load 21 KVA -- Overall dimensions 4200mm long x1600x1600mm (166"x63x63"). Electrical cabinet 1,000 high x 450x950mm (40"x 18"x38"). Approx. weight 3800 Kg (8,400 Lbs.).

NOVA PELLET - N-Plus Plant Complete Wood Pellet Manufacturing Plant including Dryer and Bagging Line: -- Capacity: 1.5 - 2.4 tons/Hr (1.4 - 2.2 metric tons/Hr). -- Raw Material: Wood chips, sawdust, and wood shavings. -- Power: 523 HP (390 kW) installed, 443 HP (330 kW) average.The Pellet Plant consists of the following main components: -- (1) Wood Chip Hopper: 706 cu. ft. (20 cbm) volume; includes: Discharge Screw and Motor. -- (1) Rotary Drum Dryer: 1.5 - 2.0 Tons/Hr (1.4 -1.8 metric tons/Hr) dry material capacity, moisture reduction from ...25% to 12% (Optional: Dryer for higher moisture contents); includes: Cyclone, Rotative Valve, Electrical Cabinet with PLC (Optional: additional Dust Filter). -- (1) Biomass Burner: Approx. 955 Lbs/Hr (433 kG/Hr) Wood Chips, max. 45% moisture content. -- (1) Magnetic Separator. -- (1) Hammer Mill: 1.6 - 2.2 tons/Hr (1.5 - 2.0 metric tons/Hr) dry material capacity, 177 HP (132 kW) installed power, 1.2" x 0.78" x 0.2" (30 x 20 x 5 mm) max. grain size. -- (1) Dry Chip Silo: 1,130 cu. ft. (32 cbm) volume, 154" (3,900 mm) diameter, 476" (12,100 mm) height; includes: Dust Filter, Pulse Jet Cleaning System, Safety System with Spark detection, and Rotative Valve. -- (1) Pellet Mill (Type: N-PLUS): 1.5 - 2.2 tons/Hr (1.4 - 2.2 metric tons/Hr) capacity; 215 HP (160 kW) main drive; includes: (1) x Die, (2) x Rollers, Electrical Cabinet with PLC. -- (1) Vibrating Screen. -- (1) Pellet Cooling Column. -- (1) Double Pellet Bin: 159 cu. ft (4.5 cbm) volume. -- (1) Automatic Packaging Machine: (5) bags/minute capacity; includes: Screen, Conveyors, Storage Hopper, Pneumatic Valve, 15 kG Bags, semiautomatic Pallet Wrapping machine. -- Auxiliary Equipment: Conveyors, Ducts for Dedusting, Fan for Silo loading, etc. -- Shipment to US port; Mechanical & Electrical installation, start-up, and training included.

NOVA PELLET - N-Eco - 45 kW, ...Pellet Mill Low specific energy consumption per ton of pellet.Specifications: -- Capacity: 770 - 1,200 Lbs/Hr (350 - 550 kG/Hr) depending on the raw material. -- Main drive: 60 HP (45 kW). -- Pellet dimensions: 0.24" - 0.31" (6 - 8 mm) diameter. -- Raw Material: Wood chips, sawdust, wood shavings: 0.02" - 0.06" (0.5 - 1.5 mm) Length; 8 - 14% MC. -- Die: 15" (380 mm) Internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 7.2" (182 mm) Outer diameter.General specification: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with: SIEMENS PCL System, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and end of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE conformity certificate.

NOVA PELLET - N-Midi - 90 kW, ...Pellet Mill with low specific energy consumption per ton of pellet. -- Capacity: 1,765 - 2,315 Lbs/Hr (800 - 1,050 kG/Hr) depending on the raw material. -- Main drive: 120 HP (90 kW). -- Pellet dimensions: 0.24" - 0.31" (6 - 8 mm) diameter. -- Raw Material: Wood chips, sawdust, wood shavings; 0.02" - 0.06" (0.5 - 1.5 mm) length; 8 - 14% MC. -- Die: 15.7" (400 mm) Internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 7.2" (180 mm) Outer diameter.General Specifications: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with SIEMENS PCL system, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and finish of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE Conformity certificate.

NOVA PELLET - N-Plus - 165 kW, ...Pellet Mill with low specific energy consumption per ton of pellet. -- Capacity: 2.2 - 2.8 Tons/Hr (2.0 - 2.5 metric tons/Hr) depending on the raw material. -- Main drive: 215 HP (160 kW). -- Pellet dimensions: 0.24" (6 mm) Diameter. -- Raw Material: Wood chips, sawdust, wood shavings; 0.02" - 0.06" (0.5 - 1.5 mm) length; 8 - 14% MC -- Die: 22.8" (580 mm) internal diameter; 0.6" - 2" (14 - 50 mm) long die holes. -- Roller: 9.4" (245 mm) Outer diameter.General Specifications: -- Pellet Mill with mechanical and electrical functioning system. -- Pellet Mill with (1) die and (2) Rollers. -- Electrical cabinet with SIEMENS PCL system, touch screen, and remote modem connection. -- High efficiency motors with IE2 standards (Energy Saving). -- Raw material dosing system (frequency controlled). -- Mechanical level sensor for the saw dust hopper. -- Vegetable oil for start and finish of production cycle. -- Automatic grease lubrication for rollers and main shaft. -- Electrical safety locks. -- CE conformity certificate.

NOVY 1872V Multi Spindle Vertical Boring Machine 12 Spindles Vertical boring machineSpecifications: -- Table Hardwood 18" X 72' -- Table stroke 0"- 6" -- (12) Spindles in line at 5" center to center, spindle nose with 0" to 1/2" chuck -- (2) drive motor 2 HP with magnetic starter -- (4) Spring loaded hold down -- Savety guard -- Foot swtich

OAKLEY H-5 Double Sided Edge Sander. -- General Specs: With 7.5 HP -1,800 RPM TEFC motor; (2) 8-1/2" x 57-1/2" Cast Iron platens; 8" x 164" abrasive belt, 4,680 FPM belt speed. -- Equipped with: One 11" x 62" Cast iron side table on one side and (1) 19" x 64" cast table on the other side, (1) cast iron radius tilting end table, end table tilts 0 ° - 45°; 6" vertical table travel w/hand wheel adjustment. -- Features: Rubber covered direct drive pulley and idler pulley,Complete with: Magnetic starter with overload protection, (8) dead head radius ends with graphite covering, and (1) steel covered spare head roll.

OGAM - PO-340, ...Dip Chain Gang Rip Saw Specifications: -- 75 HP TEFC Motor, dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise and fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGAM PO/M Straight Line Rip Saw;Specifications: -- 20 HP Main motor. -- 24"; throat capacity. -- Max. cutting height: with 12" blade 3", with 16" blade 4". -- Min. diameter of circular saw blades: 8". -- Max. dia. of circular saw blades: 16". -- Min. length of working pieces: 10". -- Variable feed speed from 50 -154 Ft./minute. -- Feeding belt width: 11". -- Spindle Speed: 4,500 RPM. -- 36"; x 60"; table.Equipped with & Features: -- Fence and rail system with one stop. -- Infeed table row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Top row of anti-kick back fingers. -- Steel smooth top hold down roller. -- Split hold down steel smooth roller around blade. -- Split hold down steel smooth roller around blade. -- Steel smooth top hold down roller. -- Chain is in excellent condition!

OGAM - PO-340: Dip Chain Gang Rip Saw Specifications -- 60 HP TEFC Motor; dip chain feed with overhead arbor. -- 4.3"; x 13.3"; Cut capacity. -- 16" Max. blade diameter. -- Power rise & fall. -- 70 mm dia. arbor. -- 2 HP Variable feed speed up to 115 FPM.Equipped with & Features: -- Automatic chain oiler. -- (3) Sets antikickback fingers. -- Adjustable infeed fence. -- Motor load meter. -- Many new saw blades.

OGDEN PUR LAMINATING LINE for Engineered FlooringSystem consists of:POS 1. PLYWOOD HOPPER FEEDER Plywood boards (two-track or single-track) are loaded vertically into the hopper and push-fed from the hopper into the Roll Coater where the rolls from the Coater take over feeding the plywood. The plywood hopper feeder is centered to the press; adjustments of the fence are via hand crank where both sides of the fence move simultaneously. The hand crank has a digital indicator to assist the operator in the width setup. Specifications:Length 4 ft to 8 ftWidth with single track 6" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Hopper capacity height 16";Pass line-height 37"; POS 2. DRUM MELTER Drum melter melts the glue which is contained in a 55-gallon drum, it pumps the glue out through heated hoses and delivers the glue to the roll coater. The roll coater sends the drum melter signals when to pump glue and when to run the pump off, a signal is sent according to glue level height. POS 3. TOP HEAD PUR ROLL-COATER Roll coater to apply hot melt PUR glue to the top of the Substrate. Roll coater will be equipped with wheel casters in order to move the unit out of the line for cleaning. Touch Screen Control panel for the coater is mounted on the left-hand side when facing the in-feed of the unit. Adjustment of doctor roller will be with hand wheel (not powered) and mechanical digital display in increments of 0.001" in relationship to application roller. Adjustment of the coating roller will be powered and will include a hand wheel with a mechanical digital display in increments of 0.001" Roll coater is equipped with a fume extraction hood which is located above the roll coater. Feed speed 20 - 250 FPMMin coater length 21"Maximum thickness 4"Minimum thickness 3/8"Effective coating width 14"Doctor roller ground chromeCoating roller silicone, 60 durometerVoltage 480 VPass line height 37"; POS 4. PLYWOOD TRANSFER CONVEYOR Conveyor length 20’Veneer lengths 2’ to 12’ ’Width with single track 7" to 12"; tolerance of +/- 1/64";Width with double track 3" to 7" tolerance of +/- 1/64";Pass line-height 37";Feed speed range from 20 to 250 FPMPop up gate will be installed to st

OLIVER 4705 SHAPER 5 HP, Sigle phase or 7.5 HP, 3-PhSpecifications and Features: -- Massive cast iron precision ground table provides a solid work surface. -- Cast iron base provides a steady platform. -- 3/4"; and 1-1/4"; interchangeable spindles are included for added versatility. -- Three spindle speeds allow more choices to produce a better finish. -- Reversing spindle gives more options for each set-up. -- Innovative dovetail design accurately raises and lowers the spindle. -- Fence is independent and features micro adjustments for quick set-up. -- Top mounted control panel includes a digital readout for spindle height. -- Large hand wheel for quick spindle height adjustment. -- Magnetic controls with emergency off switch for safer operation. -- Includes miter gauge. -- Spindle Speeds: 5,000, 7,000 and 10,000 RPM. -- Maximum Tool Diameter: 7"; Below Table, 8"; Above Table. -- Spindle Diameter: 1-1/4"; and 3/4"; Interchangeable. -- Vertical Spindle Travel: 4". -- Table Height: 36-1/2". T-Slot: 3/4" x 3/8". -- Dust Port Diameter: 4". -- 800 CFM min. -- Optional collet for router bits available special order --[1/2" Spindle for Models 4705 & 10047 Shaper]1/2" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[3/4" Spindle for Models 4705 & 10047 Shaper]3/4" Spindle for Models 4705 & 10047 Shaper$89.99Model 10047[1" Spindle for Model 4705 Shaper]1" Spindle for Model 4705 Shaper$99.99Model 4705[1/4" Collet for Models 4705 & 10047 Shaper]1/4" Collet for Models 4705 & 10047 Shaper$69.99Model 4705[1/2" Collet for Models 4705 & 10047 Shaper]1/2" Collet for Models 4705 & 10047 Shaper$59.99Model 4705[1-1/4" Spindle for Model 4705 Shaper]1-1/4" Spindle for Model 4705 Shaper$99.99Model 4705 prices may vary.

OLIVER 6910 Oscillating Spindle SanderPedestal style Spindle Sander constructed for rugged use .Specifications: -- 2 HP Motor drives and is connected through a flexible coupling, and can be installed or removed without disturbing the drive mechanism. -- Spindle speed 1,725 RPM, Oscillation speed 75 Cy/Min with 1-1/2" stroke length. -- Spindle quill runs in precision ball bearings, oscillated by a heavy duty worm & gear mechanism running in a bath of oil. -- (10) Spindle sizes provided: 1/4 x 5", 3/8 x 6", 1/2 x 6", 5/8 x 6", 3/4 x 9", 1 x 9", 1 1/2 x 9", 2 x 9", 3 x 9" and 4 x 9"; 100 grit abrasive sanding sleeve with each spindle. -- Large 24" x 24" precision ground cast iron table mounted on large trunnions that can be tilted 45° down and 30° up by use of a convenient handwheel. -- Complete with: Pedestal style stand.

OLIVER 4045 12" PROFESSIONAL TABLE SAW, with 36" FenceHeavy-duty cast iron table precision ground for accuracy; rugged machine frame construction provides maximum stability and reduced vibration.Specifications: -- 12" Blade capacity and 0° - 45° tilting arbor with digital read-out. -- 7.5 HP Motor at 3,450 RPM. -- Complete with: 52" rip fence capacity that will handle most of your work. -- 48" x 52" Cast iron table. -- Blade guard, miter gauge, push-button controls. -- Parts list & operation manual.

OLIVER 4016 10" Table Saw, 5 HP, 3-Ph w/36" Rail Specifications: -- 5 HP motor; poly V-belt drive system with belts that run smoother and with less vibration, giving you the highest quality cut available. -- Top it all off with with OLIVER'S Optimus square tube fence and a digital blade angle readout system and you've got a saw that tears it up with accuracy and in style! -- Model 4016.004 5 HP, 220V. 3-Phase.