GIARDINA DUALTECH 605 Automatic Reciprocating Sprayer:GIARDINA, model DUALTECH 605. Automatic reciprocating Spray Machine.System includes: -- In-feed roller conveyor with panel reading/detection 60-cell photodiode bar to monitor and regulate spray application, further maximizing application transfer efficiency. -- (2) Reciprocating trolleys with spray gun supports, and adjustable speed, providing a consistent speed and pattern across entire conveyor width. - Each trolley to carry (4) adjustable guns on each head (8 guns total). -- Two (2) coating circuits, suitable for solvent and water-based coatings. -- Motorized height adjustments of spray gun supports. -- Spray guns are independently adjustable in inclination; and manual adjustment. -- Through Feed Conveyor: Max. working width of 1,300 mm (51"), variable speed adjustable by means of an inverter. -- Synthetic Belt Conveyor: Ring-closed by means of an "overlapped" joint and with solvent-resistant surface treatment.Features: -- Total recovery of the lacquer deposited on the belt and cleaning of the belt with the possibility of reusing it in the spraying circuit. - Rapid repositioning of the conveyor belt system thanks to the special design of the frame. -- Air exhaust system and separation of the solid content from the air by means of two (2) suction boxes located on the two sides of the conveyor, equipped with high-efficiency twin Dry-Filters. The filtered air is exhausted to the outside by means of a centrifugal fan. -- The Enclosure Booth is made with structural irons and coated sheet steel panels. -- Control and set-up of the work parameters by means of a PLC located on a pivoting arm mounted to the machine.NOTE: Is being "Cleaned, checked and Serviced" by on of the most experienced Finishing Equipment Technician!

GIBEN - G4 512, ...CNC Router with ATC and Boring: 5' x 12' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working capacity:X-Axis 145.6" (3,700 mm), Y-axis 62.9" (1,600 mm), Z-axis stroke is 9.8" (250 mm), max. material thickness 4.7" (119 mm). -- Positioning Speed:X- & Y-Axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM).X- & Y Axes use a precision Rack & Pinion system, Z-axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing".(2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; Automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, speed 6,000 RPM, "HSD" Boring unit.(9) Independent vertical spindles with: (5) in X-axis & (5) in Y-axis. -- Machining:(1) 15 HP/18 HP peak Air-cooled "ANDERSON" Electro-spindle with: HSK F63 Adaptor, RH & LH rotation; variable speed from 1,000 - 22,000 RPM.(1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control:PC Front End with ANDI/GIBEN "SYNTEC 21MA PC based Controller" + "WINDOWS" Operating System.19" LCD Flat screen monitor; Server, full keyboard, and mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. -- Complete with:(2) 250 cbm/Hr (9 HP) "BECKER" vacuum pumps, tool holders, Collets, tool changing stand and manuals. Automatic program update according to the tool length (touch-off probe).Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is GIBEN - G4 512. Machine footprint Floor area 472"; x 197";

GIBEN - G4 EVO 510: CNC Router (ATC & Boring) + Rake & Offloading -- Specifications 5' x 10' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working Capacity:X-Axis 126" (3,200 mm); Y-axis 62.9" (1,600 mm); Z-axis stroke is 9.8" (250 mm); max. material thickness 4.7" (119 mm). -- Positioning Speed X- & Y-Axis 262 FPM (80 MPM); Z-axis 98 FPM (30 MPM). X- & Y-Axis use a precision Rack & Pinion system; Z-axis uses precision ball screws. All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors. All motion components are maintained by an automatic lubrication system. -- Work AreaFlat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing". (2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; automatic NC controlled 8-zone vacuum table. Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward-shaped parts; with: "Quick Connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit (1) 2.5 HP (1.7 kW) Motor; variable speed up to 6,000 RPM; "HSD" Boring unit. (9) Independent vertical spindles with: (5) In X-axis & (5) in Y-axis. -- Machining (1) 15 HP Air-Cooled "ANDERSON" Electrospindle with: HSK F63 Adaptor; RH & LH rotation; variable speed from 1,000 - 24,000 RPM. (1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control PC Front-End with: ANDI/GIBEN "SYNTEC" + "WINDOWS" Operating System. 19" LCD Flat screen monitor; server; full keyboard; mouse: All mounted on a mobile cart. Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. Automatic program update according to the tool length (touch-off probe).Equipped with: Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is: GIBEN - G4 EVO 510NOTE: No vacuum pump included.Tear down and loading not included.

GIBEN - G2 GENESIS 48: CNC Router (ATC & Boring)4' x 8' Fixed table; moving gantry machine with: Single zone vacuum table. -- Equipped with:(1) 12 HP ISO-30 Type ATC spindle; air-cooled; ceramic bearings; variable spindle speed from: 6,000 - 24,000 RPM. -- 6-Station Automatic Tool Changer & 2 HP 9-spindle vertical drill bank (5 in X- & 4 in Y-Axis). -- Axis Stroke1,300 mm (51") In Y-Axis; 2,500 mm (98.4") in X-Axis; 200 mm (7.8") in Z-axis. -- Max. Feed Rate60 MPM (2,362 IPM) In X- & Y-axis; 30 MPM (1,180 IPM) in Z-axis. -- Equipped with & FeaturesTool Length Measuring System (Tool Touch Off device). -- ControlANDI/SYNTECH Controller with: Network compatible WINDOWS PC based front-end; color monitor; keyboard; mouse.Full function handheld pendant absolute & incremental programming; cutter & tool length compensation; feed rate & spindle speed override; inch/metric operation; linear/circular & helical interpolation. -- Complete with:10 HP BECKER Vacuum Pump; Tool Holder’s collets; Light safety fences. -- Maintenance supplies: Grease, grease guns; full manuals; product literature.

GIBEN - KG-320, ...Edgebander (Compact)0.4 - 3 mm Edge thickness capacity min. panel width 80 mm; panel thickness 10 - 60 mm; variable feed speeds: 12 - 20 MP; electronic adjustment of the upper pressure beam.Equipped with: 2 kG Glue pot & adjustable pressure roll section with: (1) Driven roller and (3) idler rollers.Workstations -- 2-Motor end Trimming Unit. -- Top & Bottom radius Fine Trim Station. -- Top & Bottom Buffing Station.Complete with & Features: -- Programmable PLC Control. -- Sound cabin for all workstations. -- Adjustable outboard panel support.

HOMAG BHT 500 CNC FEED-THRU MACHINING CENTER (2-HEAD) + BARGSTEADT STACKER: -- Specifications:Homag "BHT 500" CNC 2-Head Through-Feed PtP Machining Center: -- Working capacity: Single panel processing "X" Axis 98.4" (2,500 mm), "Y" axis 55.4" (1,406 mm); "Z" axis 0.5" - "2.36" (12 - 60 mm) min./max. panel thickness.(2) Panel processing "X" axis 98.4" (2,500 mm), Y" axis 23.6" + 23.6" (600 + 600 mm); 0.5" - "2.36" (12 - 60 mm) min./max. panel thickness. -- Positioning Speed:Vertical boring unit(s) positioning speed "X" Axis 328 FPM (100 MPM), "Y" axis 230 FPM (70 MPM), 'Z" axis 82 FPM (25 MPM);Panel transfer belt variable feed speed from 0 - 295 FPM (0 - 90 MPM). -- Horizontal Feed-Thru Boring Units:(2) 2 HP (1.5 kW) Motors (1-motor each side) with variable rotation speed up to 9,000 RPM. (2) 19-Spindle LH units (38) total LH spindles; (2) 19-spindle RH units (38) total RH spindles, spindle are on 32 mm centers,LH Horizontal drilling support is fixed, RH support motorized & equipped with LED indicator for precision positioning, pneumatic locking & individual adjustment for positioning according to the panel size. -- Horizontal PTP Boring Units:CNC controlled horizontal PtP boring units with (2+2 spindles in the "Y" axis on each boring head, (8) "Y" axis spindles total) -- Vertical PTP Boring Units:(2) 4 HP (3 kW) Motors (1-motor each head) with variable rotation speed up to 9,000 RPM;(2) Independently controlled top mounted CNC PtP boring/grooving heads; each head with (30) independent vertical spindles, spindle are on 32 mm centers -- Grooving Saws:(2) 2 HP (1.5 kW) Motors (1-motor each head) "X" axis grooving saw with variable rotation speed up to 12,000 RPM & 100 mm dia blade. -- Operator Interface:IPC with: HOMAG "Power Control 85T" + WoodWOP + Windows "XP" operating system; icon driven software with a graphical interface allows operator to quickly & efficiently create programs & diagnose malfunctions in simple terminology. 17" TFT Color monitor; multitask operating system, input/output modules, axes override, 4-axis interpolation, diagnostic graphics aide for programming, machine data & tool management. -- Options Include: BARGSTEADT "TBH 250/QL/25/12" Vacuum Stacker device.Work cap. "X" Axis 98.4" (2,500 mm), "Y" axis 55" (1,400 mm), 2.3" (60 mm) Max. panel thickness.High-speed workpiece stack exchange with a cycle time of 35 seconds; thin work piece device for panels from 8 mm thick. -- Actual Model is HOMAG BHT 500

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HURST 205 HP / 6.9mm BTU / 15 PSIG WET WOODY BIOMASS FIRED BOILER/STEAM PLANT: -- Specifications: Complete in-place system with the following features: -- 205 HP Biomass Wood Fired Boiler, 7,073 PPH, gross steam output @ 212° F. -- Low Pressure "Fire Tube" design fire box model FB-1332-15-UF, built in accordance with ASME Code. -- Operator Interface:Allen Bradley PLC with Power Supply Rack. Pentium-based computer with network & modem remote communication capabilities with operator interface software. -- RSView Runtime for automatic operating of the steam pressure, temperatures, fuel flow & combustion airflow. -- The control system incorporates a 4-20 milliamp steam pressure transmitter to sense any changes in steam flow, boiler pressure, & regulates the fuel feed & combustion airflow accordingly. -- Complete with:Additional details on file for the scope of this Complete System's original project.NOTE: Building that houses Boiler can be included with Boiler if desired by Buyer.

HURST SERIES 45 BOILER, NATURAL GAS: -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with the National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° degrees F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with factory pre-piped, wired and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are factory packaged with operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model is: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMPERIAL CM-006 Cartridge Modular Pulse Jet Dust/Fume Collector. Designed to be the strongest, safest, and most efficient dust and fume collector in the industry. -- Overall Specs: 4,800 CFM with 2,800 sq. ft. of total filtration media operating at 2.0:1 Air-Cloth-Ratio (ACR). Factory provided compressed air (clean - dried) is supplied to manifold mounted valves providing efficient continuous pulse jet Filter Cleaning System. -- Fan/Motor: MS-180-HD-70-20 Fan driven by 20 HP premium E motor. Efficient backward-inclined fan wheel. Manual slide gate damper on fan discharge. Fan-Silencer at fan outlet. Fan capable of 4,800 CFM at 13" SP. -- Electrical Control Panel: Nema 12 (indoor) enclosure with main breaker houses fan Start, E/stop, continuous On-Demand selector switch, Local/Remote selector. Soft Start drive to reduce power peaks on start up. -- Construction/Housing/Features: Heavy 7 - 10 gage construction with no external bolt holes guaranteeing no leaks for life. Filter access door with lockable handle, heavy duty latches for one handed operation. Tool-free filter change out with 'Even-Lock technology positive stop double sealed ensures cartridges are always installed properly. Filters are fully grounded to dust collector housing. OSHA compliant full length platform and adder access. Bolted support stricture with 54" clearance for 55 Gal drum & adapter.. Discharge via 10" Rhino heavy duty collection drum sealed cover kit requires not airlock with slide gate closure, tool-free sliding coupler, and grounding wire. -- Comes with: High Entry inlet with staggered angle inlet baffle plate provides filter protection and allows material to enter at filter level causing the natural downflow material primary separation effect. Horizontal square to round transition. DWYER DCT1000 control manages the Filter Cleaning System with user-friendly software menu. Solenoid time/on-off/settings and high/low differential pressure control capability Auto/Manual control option. Compressed air pressure regulator and filter. -- Optional: Updated control panel to include a Variable Frequency Drive (VFD) to replace the Soft Start drive and keypad on cabinet door. Upgrade Controls to Include VFD. VFD reduces inrush current at startup saving energy. Also regulates system airflow by maintaining static pressure at the collector inlet. This reduces the load on the motor saving operating cost, instead of dampening the airflow with an outlet damper that is required on other starter options. On system shut down the VFD slows the fan down to a preset speed of 20 HZ for 5 minutes (the duration of the down time cleaning cycle), this prevents dust from backflowing out of the collector due to the cleaning system pressurizing the collector creating a back flow through the ductwork. Please inquire for price.

IMPERIAL - CM-002: CMaxx™ Dust Collector The CMAXX™ was designed with revolutionary cleaning technology that insures maximum pulse cleaning power. The CMAXX™ housing is the largest in the industry with the lowest internal velocities. This large housing causes more dust to drop into the hopper before attaching to the filters. The low internal velocity combined with DeltaMAXX™ filters makes this the most efficient dust collector in the industry.Specifications -- 700 Sq./ft. Filter Media; 2.55 - 1 Air to Media Ratio. -- Main Handle Operator. -- Overload protection. -- NEMA 4 Enclosure. -- Push button start. -- Emergency stop button -- Run indicator lightIncludes -- 7.5 HP Fan Motor Starter with: 1,790 CFM. -- Integrated DWYER - DCT1000 Control. -- Window kit for easy access to Dust Collector settings.

INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length and 30" maximum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- Glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Complete with: -- Wertern/Nielson 800 FJ cutterhead grinder -- Set up stand -- (15) cutterhead -- Some spare parts