POWERMATIC 221 PLANER WITH BYRD HELICAL HEAD20" x 8" Cap., 10 HP TEFC belted drive motor, BYRD Helical cutterhead, hand wheel micro-adjust table; 1 HP feed motor for variable speed from 20 - 50 FPM, segmented infeed roll and sectional chipbreaker, 4" dia. smooth outfeed roll. -- Complete with: Magnetic starter and dust hood.

POWERMATIC - RB-37, ...Single Head Wide Belt Sander1-Head, 36" width cap., combination sanding head. -- Includes: 4" Dia. contact roll & 2" wide polishing platen, micro-adjust platen; 15 HP main motor. -- Abrasive belt size: 37" x 60"; with air tensioning, air jet abrasive belt tracking.1 HP Feed drive; variable feed speed of 15 - 30 FPM conveyor speed.0" - 5-1/4" Opening with: (4) Screw jacks; double infeed & outfeed rubber covered holddown rolls. -- Complete with: Magnetic starter; overload protection; load meter; emergency brake.

POWERMATIC 72A 14" Table Saw w/Power FeederSpecifications: -- 7.5 HP - 3,600 RPM motor, takes 12" or 14" blade, (max. depth of cut is 5-1/8" with 14" blade), 1" dia. arbor and three V-belt drive, 0° - 45° to left tilting arbor. -- 24" Max. rip to left and right of blade; standard 38" x 48" table. -- Complete with: -- Accu-Fence Rip fence, standard table extensions, and magnetic switch. -- Includes: -- STEFF 2034 Power Feeder.

PRESTO XL36-20 Scissor Lift2,000 Lbs load capacity for evenly balanced load. -- 7-1/4" Lowered height. -- 36" Travel to raised height of 43". -- 17 Seconds travel time. -- Hinged platform for access to cylinders and internal power unit in collapsed position. -- 24" x 48" standard platform size. -- 3/4" Steel plate scissor legs. -- Heavy Duty hydraulic cylinders with chrome plated rams. -- Lifetime lubricated bearings on all rollers and pivot points. -- Electro-hydraulic 1 HP motor. -- Standard hand control pendant. -- Standard safety velocity fuses. -- Safety maintenance device.

PRESTO XL60-60 Scissor Lift6,000 Lbs. load capacity for evenly balanced load.Specifications: -- 10" Lowered height. -- 60" Travel to raised height of 70". -- 30 Seconds travel time. -- Hinged platform for access to cylinders and internal power unit in the collapsed position. -- 48" W x 96" L platform size, base 24" W x 86" L. -- 3/4" Steel plate scissor legs. -- Heavy Duty hydraulic cylinders with chrome-plated rams. -- Lifetime lubricated bearings on all rollers and pivot points. -- Electro-hydraulic 3.2 HP motor. -- Standard hand control pendant. -- Standard safety velocity fuses. -- Safety maintenance device.

PRESTO P3-AA ROUND PNEUMATIC AIRBAG LOAD LEVELERTurntable top with easy turning anti-friction bearings allows users to spin loads so they are always working from the near side without having to walk around the unit.Specifications: -- Automatic positions loads between 9-1/2" and 27-3/4" -- Small base allows workers to stand up close to the P3 at any position -- Stable design requires no floor lagging -- Build fork pockets for easy lagging, -- Load capacity 4,000 Lbs -- Raised height 27-3/4" -- Lowered height 9-1/2" -- Overall base 36" W x 36" L -- Turntable diameter 43-5/8" -- Shipping weight 450 Lbs

PRO-EDGE TECHNOLOGY SQUEEZETIGHT CASE CLAMP (AUTOMATIC FEED THROUGH): -- Specifications:The SqueezeTight automatic hydraulic case clamp does the work for you. The vertical pressing system with motors & independently controlled crossbars move according to the size of the piece to be pressed, mobile parts slide along linear bearings and guides. -- Operating Cycle;Once the piece of furniture is assembled on the preparation bench the operator starts the automatic cycle and the carcass enters the machine.The reading devices automatically determine the length and height of the workpiece and send this information to the PLC which positions the mobile head and the conveyor and stops the carcass in position. The beam automatically moves to the preset position.Each of the mobile heads are fitted with: (2) RH & (2) LH Horizontal pressure beams + (4) stationary & (1) adjustable top pressure clamps.The Clamping Cycle is 100% programmable & pressing is by a 10 HP (7.5 kW) Hydraulic pump system.The in-out-cross transfer powered belt conveyors are driven by "SIEMENS" AC brushless motors. -- Working Capacity:9.8" - 89.7" (250 - 2,280 mm) working width/length, 9.8" - 42.9" (250 - 1,090 mm) working height, 9.8" - 25.9" (250 - 660 mm) working depth. -- Positioning Speed:32.8 - 131.3 FPM (10 - 40 MPM) Variable speed controlled by programmable inverter. -- The carcass transfer system is located at the bottom of the bed and consists of an electro-welded steel structure on which a closed loop belt is driven by an inverter-controlled "SIEMENS" motor. -- Operator Interface:Automatic cycle control from onboard "HMI" Touch Screen control + "DELTA" VFD's & PLC with adjustment for all clamping aspects. Clamping pressure strength up to 1,200 PSI over-all. -- Complete with:(1) 98" Long powered in-feed conveyor belt with alignment guideways, (1) 98" Long powered cross-feed conveyor belt with alignment guideways & (1) 98" Long powered out-feed conveyor belt. Parameter Safety Light Curtain System. -- NOT included:Cost for Delivery, installation, and training (please call for quotes). -- Actual Model is PRO-EDGE TECHNOLOGY SQUEEZETIGHT

PROFILEMATIC 503 PROFILE SANDER3-Head feed through, sands from top at adjustable angles narrow moulding type parts as well profiled edges on panels.Equipped with: -- (3) Top VPS vibrating air-loaded sanding units, 0.5 HP vibrating motor ea., sanding heads have (2) pneumatic cylinders for sanding pressure control and oscillate with 1/2" stroke on dust-protected round guides, variable vibration speed from 200 - 1,800 RPM; adjustment range of 120ø to conform to profile, equipped with air shower to clean workpiece & sandpaper automatically. -- Part transport is achieved by a 4-1/2" wide linatex coated conveyor belt system, "quick adjustment" holddown wheels & fence system, variable feed speed 0 - 35 FPM powered by a 0.25 HP DC gear drive (forward & reverse feed mode). -- Each sanding head with its own controls for manual raise & lower, pressure control and vibrating speed. Profile width approx. 1/2" min. to 4" max., material feed through thickness up to 5"; support fences for up to 10" moulding width.

ROSE MACHINERY BDH/LC/LCFT Automated Infeed SystemAutomated, high speed Infeed System for Gang Rip Saws of all makes and models and other similar machines. -- 5-Arm Breakdown Hoist - Electric hoist accepts loads 4' wide x 4' high x 4' - 24' long; 10 HP gear motor (with brake) powers the hoist and holds the load. -- Hoist actuated through foot switches for up & down; limit switches provide max. up & down positions; (5) lifting arms tilt load at 50° allowing layers to spill onto the takeaway conveyor; 16,000 Lbs. max. lift cap. -- Landing Chain - Features: (6) Strands of roller chain; powered by a 5 HP gear motor at 60 FPM nominal rate. -- Tail end constructed with integral slide, stock transits from Breakdown Hoist; head shaft & gear motor supported by tubular steel frame with bolts to allow for leveling at installation. -- Material stops at the head end so the operator can flip & grade each piece. -- Chain races fabricated from steel, UHMW PE wear strips on the top race and on the return race; conveyor is 42' long. -- Magnetic motor starter with foot switch for operator to start & stop of the chain. -- Lateral Chain Feed Table "LCF2013-20": Feeds material 3" - 10" wide x 4' to 24' long x 1" to 3" thick; variable 50 - 200 FPM Feed rate; adjustable fence throughout 3/4" range for alignment with the Rip Saw (or other machines). -- (6) 30" long, low friction steel flattop infeed chains for long life non-marking transport; 1 HP gear motor. -- (3) Powered smooth steel & non-marking feed rolls, 2 HP gear motor; rolls & chains controlled by variable speed drives. -- (3) Overhead pinch rollers, 5" dia., urethane covered; 1st (2) pinch rollers powered by individual 2-1/2" bore air cylinders to singulate pieces onto a 2' bridge; 3rd roller keeps the board moving on the bridge; pinch rolls triggered by photoelectric cells. -- Note: Fabricated frames and appropriate parts of the items in this quotation will be painted with (1) coat of industrial grade Shady Lane Green enamel; guards and appropriate moving parts painted with Safety Orange. -- All gear motors, mechanical equipment, limit switches, sensors or photoelectric devices, as required for each item of this quotation, are supplied and mounted; all pneumatic cylinders or other pneumatic power devices and their valves supplied and mounted; connecting hoses & fittings installed. -- Filter/Regulator units supplied, mounted, and connected by hose to the valves; Note: Compressed air service to equipment is by others.

Ripsaw Feeder with 32" wide feed rolls on 18" thru 28" roll centers; will feed 3' thru 16' lumber. With 24" of in-out fence travel; feed speeds from 50 to 150 FPM; 3/4 HP feed roll drive and 3/4 HP fence drive via gear motor with brake. -- Fabricated frame of structural steel with boots that allow +/- 1" elevation adjustment. 3-1/2" dia. steel feed rolls driven by a variable frequency drive for speed adjustment; rolls are canted to aid in holding stock against the fence. -- Powered fence with 24" fence travel is easily shifted via joystick control for stock alignment with the sawblades. -- With pneumatic powered gate to keep material from feeding until the operator initiates the feed sequence. -- Urethane covered idler pinch roll is attached to the fence and is powered down at the start of the feed sequence. When a photocell detects the board is clear of the gate, the pinch roll and gate will return to their normal position. Electrical control panel ready for connection to the power supply.

ROSE MACHINERY HBR Horizontal Band RE-RIP SawThe Horizontal Band Re-Rip Saw is an effective and efficient means of ripping short blocks into as many as six (6) set rip widths. Rip widths are easily adjustable, as well as the setting for stock thickness.Advantages of the system: -- Compact, efficient use of floor space. -- Accurate cutting of rips with minimum tear-out. -- Short blocks, 4" minimum length, without taper problems. -- Straight through feed design, good for sorting. -- Minimum dust collection required. -- Single point scrap collection. -- One saw drive motor, requires less power. -- Safety, no kickback problems.Specifications: -- Five (5) rip widths - (6) optional -- 20 HP bandsaw drive -- 30" diameter band wheels, 2" wide face -- (2) 3/4 HP feed works drives -- 1-1/2 HP feed belt drive -- 1" to 6" rip width (independently adjustable in each lane) -- 10" maximum board width at maximum rip -- 4" maximum waste piece width -- 3/4" to 2" stock thickness (all lanes adjust together) -- 4" minimum stock length -- 36" maximum stock length -- 80 FPM feed speed -- 52" to 58" pass line height -- Motor starters and push buttons included, wired for 440 volt, 3 phase, 60 Hz (uses standard mag starters) -- An automatic band lubrication system is includedOptional Equipment: -- For SIX (6) LANES, add ...$5,600 (SORTER increases $3,700) -- Automatic machine grease lubrication system, add ...$ 9,200 -- Ergonomic overhead stock slide, add ...$ 5,600 -- Output conveyor and sorter for 5-LANEsingle side discharge, add ...$47,300 -- Output conveyor and sorter for 6-LANE single side discharge, add ...$51,100 -- Operator's platform, add ...$ 7,900 -- Optional voltage configuration: 220/380/440V, 50HZ, add ...$2,900 -- Start-up and training, add $1,000 per day plus expenses at costHorsepower Requirements: -- (1) @ 20 HP -- (1) @ 1-1/2 HP -- (2) @ 3/4 HPDust Collection: -- (2) outlets, 6" diameter, 5,200 FPM velocity @ 2,300 CFMCompressed Air Required: -- 90 PSI @ 1.4 CFM

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

ROSE BPUDH BOX, PALLET & UNIT DUMPING HOISTDescription: --Box, Pallet & Unit Dumping Hoist, for dumping one load at a time. --The hoist will be fabricated from steel tubing with a box cradle that pivots at the top. The three sided cradle will hold the box, pallet, or unit when it is pivoted up 135 degrees to the final dumping position. --A pair of replaceable forks hold pallets in place in the cradle. --The cradle will be pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the operator with foot switches. --Manufacture will supply all mechanical equipment, electric powered hydraulic pump, and two foot switches. --Cradle opening is: 168";L x 60";W x 60";H.Payment Terms: --50% with order, 40% prior to shipment, and the balance 10% net 30 days after receipt of equipment. Delivery is subject to the order file at the time the order is placed.Lead Time: --Delivery can be made in 12 weeks ARO at this time.Conditions: --The fabricated frames and appropriate parts of the items in this quotation will be painted with one coat of industrial grade Shady Lane Green enamel. Guards and appropriate moving parts will be painted Safety Orange. All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions: --This proposal describes the machinery to be provided by Rose Machinery Inc. to the Buyer. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized detail pages of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. We do not include any state or local sales taxes, or any permit or other fees that may be required. All field wiring, plumbing, and installation is not included. Warranty: --Rose Machinery Inc. d.b.a. Complete Millwright Services, warrants all products of its manufacture to be free of defects in material, and workmanship, for a period of one year from date of shipment. Equipment provided by other manufacturers and incorporated within equipment manufactured by Rose Machinery will be warranted to the extent of the warranty provided by the respective manufacturer. Rose Machinery agrees to repair, or replace, at its option, any component found to be defective provided the purchaser promptly notifies Rose Machinery of the defect. Rose Machinery shall not be liable for incidental or consequential damages arising from said defective material. No other warranty written or implied is offered beyond that stated above unless specifically written and signed by an authorized a

For dumping (1) load at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. The cradle holds the box as it is pivoted up to 135° to the final dumping position. The cradle is pivoted with a hydraulic cylinder driven by a 3 HP hydraulic pump. The cylinder is manually energized via operator foot-switches. -- System includes all mechanical equipment, electric powered hydraulic pump, and (2) foot switches. All wiring and controls by others. ~ Accepts a standard 96" long X 60" wide X 60" high box.

For dumping (1) load of fingerjoint blocks at a time. Hoist is fabricated from steel tubing with a box cradle that pivots at the top. -- 3-Sided cradle will hold the box, pallet, OR unit when it is pivoted up to 135° to the final dumping position; cradle opening is 88" long X 48" wide X 50" high . -- A pair of replaceable forks hold pallets in place in the cradle. The cradle is pivoted by a hydraulic cylinder driven by a 3 HP hydraulic pump. The hydraulic cylinder is manually energized by the fingerjointer operator with foot switches. -- Scope of supply includes all mechanical equipment, electric powered hydraulic pump, and two foot switches. All wiring by others.

ROSE GBUB-80 Glue-Bound Unit Breaker. Machine breaks the glue bond in a staggered stack of finger jointed material - see picture of material with the checkerboard end pattern. --Features -- Equalized Hydraulic squeeze, provides uniform load compression. --Hydraulic length change. Air operated Locking Pins on the Backstop Platen. --Backstop platen position indicator. --Simple manual controls for load length adjustment and crushing stroke on the control panel. --Heavy Duty Structural Steel Construction, Ease of Maintenance and Simple Operation (no cables).Does not use cables!Specifications: --Maximum opening is 16’-10"; for a single 4' x 4' x 16' unit. --Backstop Platen locks at 12" increments (2' minimum load length) --Pressure Platen, hydraulic actuated with 18" stroke. --Platen size 5' x 5' --5 HP Hydraulic Unit with a Pressure Compensated Pump (approx. 1 minute squeeze time) --Overall size approximately 5' x 25' x 7' high --480 VAC, 60 hertz, 3 phase, 30 ampsOptions: --10 HP hydraulic unit with approx. 30 second squeeze time, add $4,200 --Double unit capacity; crushes (2) 4' x 4' loads with 5' x 10' platen, add $19,700 --Automated Control Package with 2 Remote Controls for initiation of Pressing Stroke; Automatic open and hydraulic shut down; PLC Controls, automated load length adjustment with lighted indicators, add $ 7,400

This item is in an Auction on exfactoryauctions.com. Go here to view item: http://exf.ac/i6s ROWLEY & HERMANCE Sash Sticking Machine Specifications: Table size 5” x 46”. Equipped with: 3 HP - 1,750 RPM Motor. (2) 2” Dia. x 2” W Serrated upper feed rollers.

RUVO 2200 Stair Stringer Router, Top/Bottom, Semi-automatic. -- Size capacity (nominal): 2" Thick x 12" - 15-3/4" wide stringer size; semi-automatic operation. -- (2) 5 HP, 25,000 RPM Router motors for top & bottom heads. T & B heads are arranged to jump in & out to facilitate open plan stairs; automatic pneumatic clamping of stringers, spring loaded side pressure to keep stringers against the fence. -- Mirror-image routing on (1) pair of stringers at one time, graduated template automatically sets up to stated tread & rise, cuts standard wedge taper for both treads and risers. -- Includes: Clamp and feed system & safety covers. -- NOTE 1: Stair Router rebuilt in 2022 by BUILDERS AUTOMATION. Replaced 3HP with new 5HP routers. Reconditioned air cylinder pistons, air-over oil booster, replaced air lines, etc.. Painted from green to Blue.

RUVO 505, ...Prehung Door Machine.Handles a wide range of door, jamb, and hinge sizes. - Bevels doors and door hinges. - Designed for efficient handling and operation. - Fast, accurate hinge and lock backset adjustment. - Residential, Commercial, Architectural, and Labeled Fire Doors.Features: Heavy duty powered 3° beveler/sizer. Routers to ease door edges. Accurate target scales. The 4-hinge and jamb route location changes fast and precisely. A similar system for the backset on hinges & locks. Provision for single and double-belled doors. Controls interlocked by a PLC. Auto door sizing is fast to adjust the lifter bar by digital input and servo control. Reliable, long-lasting non-contact sensors. Fast push-pull controls with a friendly touchscreen HMI. Hinge screw gun and pre-drill included.Technical Details: Max Door Height: 6’ - 9’ or ADA Specs 6’ - 8’. -- Door Width: 1'-6"’ to 4’. -- Door Thickness: 1-3/8"; to 2-1/4. -- Jamb Size and Styles: Up to 1-1/4"; x 10";, all styles. -- Number of hinges: Up to (4); Hinge Size: 3-1/2" to 5";; Hinge Radius 1/4" to 5/8". -- Hinge Backset: Scaled as required -- Lock Bore Sizes: 2-1/8"; Standard. -- Lock bore Backset: Scaled to 5";. -- Lock Bore Latch plate: Up to 1-1/4"; x 8";.Machine Size: 18’ x 3’ x 7’; Approx. Machine Weight: 3,200 Lbs; Electrical: 4-Wire, 230/3/60 and draws 25 Amps. Requires a 1/2" airline using 40 CFM @ 90 PSI.Options Include: -- Built-In Power Beveler Vacuum System......$ Please call. -- Screw Driver............................................... Included. -- Pre-Drill Kit.................................................. Included -- Digital Readout ..........................................$ Please call.RUVO 512, ...Heavy Duty Strike Jamb Mortising Machine.For Jam Sizes up to 1-1/4"; x 9"; x 10";. Strike Plate mortise to 6";. Compliments Jamb Preparation of the RUVO 505 and 405. Operated by one worker.Unit Includes: -- Adjustable Jamb Stops. -- Heavy Duty Construction. -- Foot Pedal Actuated Clamp. -- 120 Volt, 1-Phase, 20 Amps. -- 1/2" Airline needs 0.5 CFM @ 100 PSI. -- 1.5 HP Router.@ 23,000 RPM. Additional Cost for the RUVO 512 above ...$Please call.Material Handling for the Line:Loading Device..........................................$ Please call.Unloading Device.......................................$ Please call.