SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. &#9679 Edgebanding thickness 1 mm, min = R 30 mm &#9679 Edge thickness 2 mm, min = R 50 mm &#9679 Edge thickness 3 mm, min = R 80 mm &#9679 Panel thickness 10-60 mm with edge thickness 1 mm &#9679 Panel thickness 10-60 mm with edge thickness 2 mm &#9679 Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: &#9679 Top & Bottom Trimming unit &#9679 Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired &#9679 Banding station &#9679 Edgeband coil stand &#9679 Standard-size vacuum pod for articulated arm &#9679 80 mm dia. (3") dust extraction outlet &#9679 Foot pedal activation/de-activation control &#9679 Larger feed roller

SNX nVISION System2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. Edgebanding thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with the foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application to large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large inter-changeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: Top & Bottom Trimming unit Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired Banding station Edgeband coil stand Standard-size vacuum pod for articulated arm 80 mm dia. (3") dust extraction outlet Foot pedal activation/de-activation control Larger feed roller

SORBINI TM/95-2F Flow Coater Specifications: -- 24" Coating width, 4" max. thickness, hand crank controls curtain thickness, (1) head gravity feed. -- 2 HP feed motor for variable feed speed from 90 - 350 FPM, (1) 1.5 HP circulating pumps, (1) stainless steel tank & return reservoir. -- Conveyor: 24" Wide, 60" Long at infeed, 72" long at outfeed. 34" long center belt.

CEFLA/SORBINI, VS 34/ACT/1600 - Top Only Panel cleaning machineEquipped with:One (2) Anti-Static ionization bar. One (2) soft horse hair brush, in opposite rotation to panels feed direction, 400 RPM brush speed.One (2) timed, compressed air blower Min. work piece length 290 mm (11.5";).Belt conveyor with variable speed feed from 3 - 16 MPM (approx 10 - 52 FPM). Hand wheel for thickness adjustment.

SUPERFICI/VALTORTA F1SPECIFICATIONS: --Belt width - 1370 mm / 54 inches, Roller width 1500 mm / 59 inches --Working height 900 mm / 35 inches --Panel thickness 3 - 120 mm / .11" - 4.75" -- Min. panel length - 300 mm / 11.8" -- Application roller diameter - 245 mm / 9.6" -- Standard hardness of the application roller - 50Sh -- Doctor roller diameter - 175 mm / 6.8" -- Feed speed - 7 - 20 m/min / 23 - 65.5 fpm -- Compression air consumption 25 NI/min -- Approximate installed power 2kW

SWEED MODEL 517 SCRAP CHOPPER With Dump HopperFeatures: --The Model 517 XHD provides a large cutting capacity. This is the chopper of choice for custom applications or for operations converting substantial quantities of linear scrap materials. Prepared for an abusive environment, the 517 XHD has a strong 1/2"; plate steel housing. The 517 XHD also features a magnetic starter to protect workers from an unexpected restart after loss of power. The powerful air activated feedworks is controlled with a footswitch for operator safety, and is also capable of despooling scrap wire and cable from reels. --Additional safety options are available. Material Reference The recommended model of scrap chopper is determined by scrap size, scrap volume, and requested custom features. Please consult a SWEED representative to determine the appropriate scrap chopper for your application.» High-tensile bale wire» Small, solid, aluminum and copper bars» Jacketed and non-jacketed wire and cable» For other materials, consult SWEED --Electric Motor 5 HP --Infeed Opening 6 "; W x 1 "; H Cut Length 3 ½"; standard (smaller cut lengths available with different knife configurations) --Number of Stationary Knives 1 --Number of Rotating Knives 1 standard --Overall Chopper Dimensions 56"; L x 34"; W x 30"; H --Chopper Weight 1,492 lbs --Chopper Shipping Weight 1,577 lbs -- Include Stand and Gaylord

TAKEKAWA - RG-30S, ...Straight Line Rip SawSpecifications: -- 15 HP - 5,000 RPM Belt driven arbor, overhead arbor design. -- 1-1/4" Dia. arbor. -- 12" Dia. max. blade cap., 2-3/4" max. depth of cu.t -- 12" Min. part length. -- Throat clearance to the right of blade 26". -- Table size: 74" Long x 38" wide; 2 HP step feed drive, 33 - 66 & 131 FPM.Equipped with and Features: -- Automatic chain lubrication. -- Top pressure system with spring loaded rollers. -- Adjustable rip fence. -- Antikickback fingers. -- Push buttons and magnetic starters.

16" Blade cap., 3-3/4" max. cutting height, 5 HP - 3,600 RPM direct drive motor, arbor tilts 45ø, 44" x 40" cast iron table size, table with miter gauge slot. -- Complete with: Rack & pinion fence and large hand wheels for easy adjustments.

TANNEWITZ - XJ, ...Table SawSpecifications: -- 5 HP - 3,600 RPM Fan cooled motor, 1" right tilting arbor Table Saw with a 1-piece main table; table size 42" wide x 44-1/2" deep. -- Base formed from hot rolled steel of 5/16" thickness & welded into (1) solid unit; 10" dia. handwheels for easy adjustment of tilting, raising & lowering of arbor. -- Complete with: Extended rack & pinion adjustable rip fence for greater ripping capacity; left- & right-hand T-slot miters. -- 16" Blade dia., 4" dado width cap.; 4" cut depth at 90°; 3" cut depth at 45°. -- Equipped with: Taper pin miter with micrometer adjustment on fence, magnetic controlled off switch, and 6" dust outlet with auxiliary rear opening for easy access. -- Power safety electrical breaker box included. Please NOTE: No blade guard.

TAYLOR 40 Section Clamp Carrier.Specifications: -- 40-Section, 8-1/2' width capacity -- Average 4/5 clamps per section (175 clamps total), all with 32" max. clamp opening. -- Equipped with (175) clamps plus a pallet of spares that require repair, 32" clamps with 2-1/2" high jaws .Complete with: -- Heavy Duty Drive for rotation,& clamp tightening. -- Foot pedal control. -- Includes a glue applicator.

TAYLOR - 6-Section Pneumatic Clamp Carrier6-Section x 10-1/2' width cap.; (36) total clamps; 30" opening on clamps; 3-1/2" high jaws; includes: Pneumatic rotation, tightening, and panel flattening. -- Overall assembled dimensions: 9-1/2' deep x 13-1/2' wide x 9' tall.NOTE: Tear down not included.

JLT Clamp 713A-8-LCS (8) Section Large Capacity Door ProLarge capacity (8) section rotary door clamp for the medium to large cabinet shop. Produce up to 400+ cabinet doors per day. -- Each section includes: 38" x 96" maximum clamping capacity w/ 2-1/2" high jaws, (4) vertical clamps and (2) horizontal clamps. --Clamp & Square Multiple Cabinet Doors with Vertical Center Rail – (2) 38″ x 45″ Doors Side by Side Double Door Clamping. -- Includes: Heavy-duty, pneumatic drive for rotation, pneumatic clamping and squaring assembly.Actual model # 713A-8S-129W-68H-80D-NS-M-LC-L-M2

--In Auction: https://exfactoryauctions.com/Detail/CR-230068/event/A122024$1 --No Reserve!-- TAYLOR 800036 7' W 12-Section Semi-Automatic Pneumatic Clamp Carrier, with Flattener & Tightener Equipped with: (71) 32” Cap. Clamps, with 4-5/8” W x 3-1/2” H Jaws. Air motor drive. Dual foot pedal control. Complete with: Pneumatic Panel Flattener. Pneumatic Clamp Tightener.

TAYOR 16-Section Clamp Carrier 20.5' width cap., (7) clamps per section (128 clamps total). .48" max. clamp opening clamps with 4-1/2" X 3 1/4" jaw height (128) Rocker plates 4" X 6" @ 80-1706 (purchase in June 2024)Complete with: -- Semi-automatic clamp tightening, -- (2) Air drive carrier rotation. -- (2) Pneumatic panel flattener -- OAL approx. 24' X 14' X 12'Note: The buyer will be responsible for tear down and loadingMachine model CC 20,5-16-481

TAYLOR - 20-Section: Clamp Carrier Specifications -- 8-1/2' Width cap. -- 39" Max. clamp opening; 2-1/2" Jaw height. -- Approx. (4) clamps per section.Equipped with: -- (75) Clamps total. -- Pneumatic tightener. -- Pneumatic panel flattener.Complete with: -- Air drive carrier rotation. -- I-Beam chain assembly.NOTE: Already taken down.

TERCO NORTHSTAR 10-8 Spindle Carver.8-Spindle Carver with 10" center-to-center chuck spacing. -- (2) 0.5 HP - 3,450 RPM spindle motor direct "belt drives" spindles for 11,000 RPM rotation. -- 36" Long carving cap, with optional length extensions up to 72". -- Manual rotation for round parts. -- Operator manually traces the pattern details of the master with copying stylus. -- Capable of doing both base relief (flat backed) and 360° full round carving. -- Includes: (1) Set roughing bits, (2) sets finishing bits, tools, and manual.

TIMESAVERS 252-4-IC, ... Wide Belt Sander, 4-Head.4-Head, 51" cap. - Great sander for solid wood and veneer panels equipped with (2) Contact rolls and (2) Air platens. Head Configuration1st Head: Rubber covered contact roll, 9-1/2" dia. 60 - 70 Durometer, 40 HP motor.2nd Head: Rubber covered contact roll, 9-1/2" dia. 50-60 Durometer, 30 HP Motor.3rd and 4th Head: Finishing platens, 2-1/2" wide "Veneer Saver" inflateable platens with adjustable timers for leading and trailing edges, 20 HP motor each head.Specifications: -- 38" Constant pass line height of Vacuum conveyor with suction fan and motor bed assembly for veneer and solid wood sanding. -- Adjustable air floating infeed and outfeed hold down shoes. -- 52" x 103" abrasive belts with "POSI-TRAK" electronic tracking.Equipped with & Features: -- Motorized part thickness adjustment with mechanical digital readout. -- Auto part thickness set-up, 0" - 6" opening. -- Hydraulic feed belt operation of 15 - 45 FPM via 7-1/2 HP hydraulic pack. -- 4-Motor load meters, controls mounted on belt loading side. -- Disc brakes on sanding head motors. -- 30" Infeed load area.

TIMESAVERS 2321-24-01 Wide Belt Sander (2) Heads43" width cap. Drum, Combination HeadHead configuration:1st Head: 8" Dia. rubber covered contact roll 65/70 Duro. , 25 HP motor (4,000 RPM);2nd Head: Combination head with 5-1/2" dia rubber covered contact roll and 2-1/2" wide finishing platen, 20 HP motor (3,500 RPM)Specifications: -- 43" x 75" Abrasive belts with dual "Posi-Trak" electronic solid-state tracking --Conveyor belt feed with AC inverter variable feed from 15 - 45 FPM. -- Infeed & outfeed spring loaded holddown shoes or rollers on all heads --Automatic part thickness set-up, motorized thickness adjustment with digital indicator, 0" - 6" opening, and infeed safety stop bar. -- (4) Jack screws for bed adjustment --Compressed air requirements: 4 CFM @ 90 PSI --Dust extraction requirements: 2,700 CFM --Electrical requirements: 126 full load amps @ 230 VoltEquipped with & Features: -- Controls mounted on belt loading side -- 14" infeed conveyor area -- Sanding head motors with air caliper disc brakes, and motor load meters. -- Well maintained and serviceNOTE Constant Passline Sander 33"-38"

Timesavers 2321-45-01 (2) Head wide Belt Sander51" Width cap, Drum, Combination HeadHead Configuration1st Head: Steel contact roll, 8" dia., 30 HP motor.2nd Head: Combination head with a rubber-covered contact roll 5-1/2" dia. and 2-1/2" wide segmented finishing platen, 25 HP motor, (2) dial indicators for contact roll height adjustment.Specifications: 52" x 103" Abrasive belts, -- "Posi-Trak" electronic tracking & pneumatic tensioning, conveyor belt feed. -- 15 - 45 FPM Variable feed speed with inverter control, -- Automatic conveyor belt tracking; -- Double in-feed & out-feed spring loaded hold-down rolls.Equipped with & Features -- 0" - 5" Max. motorized part thickness opening with automatic part thickness set-up, -- Air-operated disc brakes, -- Motor load meters, -- 14" in-feed conveyor area, -- In-feed emergency stop bar."Owner's manual included

TIMESAVERS 2331-04-334 DUAL HEAD DENIBBING SANDER2-Head, 42" width capacity Sanding / Denibbing system. -- (2) 5" Wide platens featuring a "dual" action head with a high-speed orbital movement and combined back & forth oscillation to remove abrasive belt cross-grain scratches; platens designed with a quick change system for abrasive material. -- (1) Nylon abrasive impregnated (150 grit) Cleaning / De-Nibbing brush, 10" dia., drive unit for brush rotation, brush wear adjustment via jack screws. -- Vacuum holddown conveyor system with variable feed speed 5 - 15 FPM. -- Double infeed and outfeed holddown pinch rollers. -- Power raising and lowering of the conveyor bed with AUTO-SET feature, 0" to 6" part thickness capacity. (4) DUFF-NORTON acme screw jacks under conveyor bed, 36" infeed conveyor area.....below in the comments see what the current owner says: