CANTEK CM626 Single-Sided Planer with Helical Head26" x 11-3/4" capacity Planer w/Helical Cutter HeadFeatures: -- Spiral cutterhead with (6) rows insert knives provides high removal, superior finish, and low noise. -- Solid cast iron construction. -- Variable feed speed. -- Drive top and bottom feed rolls. -- Front & rear bed rollers easily adjusted from the front of the machine. -- Power table elevation by digital thickness control. -- Serrated solid infeed roll. -- Section chip breaker. -- Anti-kickback fingers for added safety. -- Dual heavy jack screws with slides for accuracy & rigidity. -- Dust/Chip exhaust outlet 6"; in diameter. -- Sound dampening machine cover. -- All operations on a convenient control panel. -- Two-sided solid carbide inserts are easily changed while providing optimum wear lifeSpecifications: -- Maximum planing width 26" -- Maximum planing thickness 11 ¾" -- Minimum planning thickness 0.15"; (4 mm) -- Maximum depth of cut 0.31"; (8 mm) -- Minimum planning length 10.35" (263 mm) -- Table area 35" x 27" -- Feed speeds variable 16 – 70 FPM -- Main motor 20 HP -- Feed motor 1 HP -- Table motor 1/2 HP -- Knives 30 x 12 x 1.5 qty 100 -- Cutterhead 4 ¾" dia. x 5000 RPM -- Top feed rollers 3" dia. -- Dust hood outlet 6" dia.

CANTEK - GOODSPEED CP-1250 AP Hydraulic Copy Lathe. -- General Data: 44" Length cap. with 4" min. length of stock and 1/2" - 4" max. diameter cap., hopper feed with automatic chucking, square or round stock can be hopper fed. -- Equipped with: 7.5 HP Spindle motor, 1,800 - 3,200 RPM spindle speed adjustable by pulley change, 3 HP hydraulic motor. -- Complete with: Swivel control panel, PLC sequence controller built into separate control cabinet, (3) pressure gauges, automatic way & support collar lubrication & safety wire mesh across the front of machine. -- Includes: Two hydraulic copiers (rough + fine). Travelling steady rest and installed knives. -- Production capacity: Approx. (5 - 7) pieces/Min for 600 mm length, (3 - 5) pcs./Min for 900 mm length, (2 - 3) pcs./Min for 1,200 mm length, depending on cutting speed, type of material, etc. -- Electrical load: 11.4 amps, 10.5 HP @ 575/3/60.volts.

CANTEK C251 24" WIDE BELT SANDERSpecifications: -- 24" Width cap. - sanding head with a rubber covered contact roll and adjustable finishing platen, 10 HP motor main drive motor. -- 25" x 60" Abrasive belts, pneumatic abrasive belt tensioning. -- 0" - 5.9" thickness capacity, Power elevation for thickness opening with digital thickness programming. -- Variable conveyor feed speed from 15 - 50FPM, 1 HP feed motor. -- 5.9" Max. working thickness, 13" min. working length, -- Spring loaded holddown rolls.Complete with: -- Magnetic controls, (2) 4" dia. dust collection outlets, and safety shutoff. - 825 CFM Dust collection required. Optional: 10 HP Single Phase motorElectronic belt tracking for optimum belt life and sanding results. Ammeter for load monitoring main drive motor. Disc brake on the main motor. Pneumatic belt tensioning with quick release outboard support. Safety Interlocks are located on all access doors.

CANTEK MODEL CFS100 / EM-12 DEFECT SAW AND END-MATCHING SYSTEM:Consisting of a CANTEK model "CFS-100" Optimizing Cut-Off Saw followed by a CANTEK Model "EM 12" Through-Feed End Matcher and with the following specifications and features: CANTEK "CFS-100" OPTIMIZING CUT-OFF SAW -- Up to 20 mm X 200 mm or 100 mm X 100 mm( 3/4" X 7.87" or 3.9" X 3.9" cutting capacity with 18" x 30 mm bore sawblade is driven by a 10 HP motor driving the saw spindle at 3,200 RPM; 2.7 HP servo drive feed system drives the stock up to 260 FPM; 0.787" min. distance between crayon marks; requires 75 to 80 PSI at the saw and 100 to 120 PSI at defect blow-off station. Machine comes completely wired and programmed. -- Machine is ideal for separating crayon marked waste zones from useable material before entering into a feed-thru End Matcher; provides (3) times greater production than manual cut-off saws.5% + Material recovery (yield increase) over manual cutting; compact and user-friendly design; controller adopts an industrial grade computer that employs a 32-bit floating-point DSP system and features flash and battery backup SRAM for double security; superior to conventional PC-based controls, it can fully eliminate the machine going down or being damaged due to a poor environment, such as, unstable voltage, high temperature, sawdust, etc. -- With defect blow-off system combined with computerized logic control permits the blow-off time and the length of defect to be set as desired; provides efficient defect removal and eliminates defects from bumping against the sawblade, resulting in the machine going down or sawblade damage. -- Computer control provides easy and fast maintenance; feed system driven by a servo motor for fast and accurate motion and position control; max. feed speed up to 260 FPM; cutting rate up to 80 cuts per minute with cutting accuracy within approx. ±1mm / 0.40"; control employs a touch screen for easy learning and operation.Features: -- New machine design features maximum maintenance convenience; high quality electric components provide maximum dependability; safety guards for maximum operator protection; 48" long infeed table standard - longer available option; 18" carbide blade included.(5) Cutting modes include: -- Adjustable end cuts to a max. of 10mm (0.4") -- Fixed length of cutting mode. -- Sequential cutting mode with (10) sets of cutting sizes held in memory (for sequential cutting mode only). -- Cutting on fluorescent marks with double-end trimming (perfect solution for end matching). -- Reading fluorescent marks with double end trim, fixed-length, random length end match, and finger joint block cutting. CANTEK "EM-12" END MATCHER -- Continuous through-feed system; handles random length min. 10.6" to any length x 0.4" to 1.38" thickness x 12" width capacity; -- 295 FPM max. feed speed; average speed of 75 FPM based on 6'-6" board lengths; with 118" infeed and 98" outfeed tables; -- 5.5 HP Shaper motors, 1 HP feed motor an

Non-Oscillating Edge Sander with end sanding kit. -- 6" Wide x 108" long belt. -- 6" x 40" Graphite covered platen. -- 1 HP -1.5 HP, or 3 HP -2 HP, 3-Phase motor w/magnetic switch. -- 7" Diameter drive pulley. -- 7-3/4" x 37" Front table with a 6" vertical adjustment. -- End table for radius work with a 6" vertical adjustment. -- Heavy laminated tables, fabricated steel base and swing-away dust hood.

CANTEK D405A 10' Sliding Table Saw Specifications: Max. cutting length 126". Max. depth of cut: 4.13" at 90° (355 mm), 5.12" at 90° (400 mm), 2.75" at 45° (355 mm). Main saw: 7-1/2 HP Motor, Blade dia. 16", Arbor dia. 30 mm (1.18"), Arbor tilt 0° - 45°, & Blade speeds 3,000, 4,000, & 5,000 RPM. Scoring saw: 1 HP - 8,000 RPM Motor, Blade dia. 120 mm (4.72"), & Arbor dia. 20 mm (0.79"). Equipped with: 15-1/2” x 126” x 35-1/4” H Precision anodized aluminum sliding table with Prismatic rollers running on precsion ground steel guides, 21.6” x 35” x 35.3” H Cast-iron fixed table, 12.6” x 32.7” x 35.3” H Auxiliary table. Main saw blade motorized height & tilt adjustment. 39-1/2” L x 3-1/2” H Aluminum rip fence, with 130 mm (51.18”) Cutting cap. Aluminum extruded crosscut fence, with (2) Flip stops with miter angle adjustment, & Sliding outrigger support. Eye-Level touchpad control, with LED Displays for main saw blade height & tilt. Overhead blade guard. CURRENCY NOTE: Negotiable Price is listed in U.S. Dollars.

CANTEK D405A 10' Sliding Table SawSpecifications: -- Max. cutting length 126". -- Max. depth of cut: 4.13" at 90° (355 mm), 5.12" at 90° (400 mm), 2.75" at 45° (355 mm). -- Main saw: 7-1/2 HP Motor, Blade dia. 16", Arbor dia. 30 mm (1.18"), Arbor tilt 0° - 45°, & Blade speeds 3,000, 4,000, & 5,000 RPM. -- Scoring saw: 1 HP - 8,000 RPM Motor, Blade dia. 120 mm (4.72"), & Arbor dia. 20 mm (0.79").Equipped with: -- 15-1/2"; x 126"; x 35-1/4"; H Precision anodized aluminum sliding table with Prismatic rollers running on precsion ground steel guides, 21.6"; x 35"; x 35.3"; H Cast-iron fixed table, 12.6"; x 32.7"; x 35.3"; H Auxiliary table. -- Main saw blade motorized height & tilt adjustment. -- 39-1/2"; L x 3-1/2"; H Aluminum rip fence, with 130 mm (51.18";) Cutting cap. -- Aluminum extruded crosscut fence, with (2) Flip stops with miter angle adjustment, & Sliding outrigger support. -- Eye-Level touchpad control, with LED Displays for main saw blade height & tilt. -- Overhead blade guard.

CANTEK D405A SLIDING TABLE SAWThe Cantek D405A Sliding Table Saw is the ideal sliding panel saw for high accuracy cutting of sheet materials to produce kitchen cabinetry, furniture, millwork operations, and more. This is our most industrial saw with a manual setting rip fence. The 10' sliding table is made from a precision aluminum extrusion and runs on precision linear guide rails. It has motorized rise/fall and tilt of the blades. Features: -- 126" Cutting length w/scoring; 126" x 15.5" Anodized sliding table that locks in any position for easy loading. -- Motorized Saw blade up or down movement by 1/4 HP electric servo motor; tilting by manual handle wheel. -- Scoring unit for clean, accurate chip-free cutting, ready for edge banding. Specifications: -- 7.5 HP Main saw motor; 45° tilting (30 mm) main saw arbor; 14" Main blade dia.; 3,000/4,000 & 5,000 RPM arbor speed. -- 5.3" Max. material thickness at 90°; 3.1" at 45°. -- 1 HP Scoring saw motor, 5" dia. scoring blade; 8,000 RPM. -- Equipped with: 49" Max. ripping cap.; micro-adjustable rip fence and extendable crosscut fence to 10' with (2) flip stops. -- Articulating overarm protection guard; outboard and rear extension tables. -- Includes: -- Saw Blade(s), Maintenance Tools, Operators' & Parts Manual and covered by (1) Year Warranty.

CANTEK D405ANC 1-Axis SLIDING TABLE SAWSpecifications: -- 126" Cutting length w/scoring; 126" x 15.5" Anodized sliding table that locks in any position for easy loading. -- Motorized Saw blade up or down movement; motorized tilt with digital readout via 1/4 HP electric servo motor. Equipped with: -- 7.5 HP Main saw motor; 45° tilting (30 mm) main saw arbor; 14" Main blade dia.; 3,000/4,000 & 5,000 RPM arbor speed. -- 5.3" Max. material thickness at 90°; 3.1" at 45°. -- 1 HP Scoring saw motor; 20 mm arbor; 4.72" dia. scoring blade; 8,000 RPM. -- Features: -- Motorized rip fence control with eye level control; 51" Max. ripping cap.; crosscut miter fence to 10' with (2) flip stops. -- Articulating overarm protection guard; outboard and rear extension tables. -- Includes: -- Saw Blade(s), Maintenance Tools, Operators' & Parts Manual and covered by (1) Year Warranty.

CANTEK MRS-610M-4 GANG RIPSAW WITH (4) SHIFTING BLADES: Specifications: -- (4) Shifting Blades and 4.2" Max. cutting thickness without pressure plate, 3.7" with pressure plate; 24" Max. cutting width; 35.4" Max. material width of pass-through; -- 60 HP Saw motor (larger optional); 2.8" (70 mm) Saw arbor diameter turning at 3800 RPM; 12" Min. or 14" max. Sawblade diameter; 2.8" (70 mm) Sawblade bore when mounted directly on shaft, 3.5" (90 mm) when mounted on saw sleeve; -- 5 HP feed motor with variable feed speeds from 25 to 200 FPM; 1/2 HP pressure roller raising motor; 24" Min. stock length; 31.9" Min. stock length with board under (2) rollers.Features and Benefits: -- The main frame is cast iron, all the main parts are enclosed, ensuring protection and perfect stability -- Nickel chrome steel saw arbor with 70 mm OD double keyed quick removal sleeve. -- Heavy duty precision straight line feeding caterpillar chain type. -- Feed chain with easily replaceable bolt in cast steel or urethane pads - optional. -- The top pressure roller system is electronically positioned from the front control panel with regard to lumber thickness with position readout. -- Top roller hold down system is mated to the servo positioning short stock shoe providing optimum straight-line ripping performance and comprehensive safety. -- Pneumatic pressure (infinitely variable) to the holddown feed rollers provides better control of the lumber. -- Nickel chrome steel saw arbor. -- Variable feed speeds of 16 - 200 FPM. (5 - 60 m/min) via an inverter motor and speed control with led readout. -- Electronic overload sensing system is integrated to the inverter feed system providing automatic speed reduction under heavy amperage load. -- New - short stock cutting device included. -- Digitally controlled lubricator for chain. -- Centralized lubrication system. -- (2) Powered top & bottom outfeed rollers are a standard feature. The powered roll system facilitates positive flow of the stock through the gang saw and onto outfeed conveyors or transfers. -- (3) Rows of anti-kickback fingers. -- Telemechanique - automatic star-delta starter (low amperage soft-start) and low voltage controls -- Controls are mounted on the saw for easy convenient machine operation. -- Includes 12' infeed table -- Gang saw sleeve is an optional extra. -- Electrics to 230/460 or 575-volt, 3-phase, 60-cycle to UL/CSA standards -- Complete Shifting Fence Infeed Tables and complete Outfeed Sweep Systems, handling decks and Stacking Systems are available.Options available: -- Add a 75 HP saw arbor motor instead of 60 HP - including a Wye-Delta low amp Starter. -- 100 HP Saw arbor motor in lieu of 60 HP - including Wye-Delta low amp Starter -- 125 HP Saw arbor motor instead of 60 HP - including Wye-Delta low amp Starter. -- Short Stock Feeding device (min. length 12" - must use 12" blades for max. thickness of cut of 2.16" (55 mm). -- 20 mW Laser (FP MLC1320W) & Laser Holder w/12" B

102" Width cap. Veneer Clipper completely reconditioned to modern mechanical and safety standards to meet todays manufacturing needs. Original machine frame will be fully disassembled cleaned and repainted. The frame is the only part of the original machine used and all components are upgraded.Mechanical upgrades include:1. 2-Hand anti-tie back push button cycle activation 2. Photo safety eyes located on both front and back side of blade3. Full safety guarding including a fully enclosed knife section 4. New electric motor and gear box main drive system5. New knife and shear bar6. All new electrical/control box with Components and Wiring7. All new upgraded bearings including replacing Babbitt bearings Machine comes with a full (1) year warranty

CARGATE D-860 Rotary Veneer Lathe, Heavy Duty: -- Built specifically to handle large-diameter logs as well as small logs. It has a log length capacity of an easy 8'-6" and a diameter capacity of up to 5', peeling down to perfect 4" cores for optimal log utilization. -- This moneymaker looks like a big brother to a Premier Lathe. It comes complete with beefy Bull Gears and boasts plenty of output capacity along with the following main features and components:Specifications: -- BRUNETTE MACHINE WORKS Hydraulic Retractable Spindles - 4" inner, 8" and 11" outer. These are the same spindles as are utilized on a Premier Lathe. -- The spindles are driven by angle-cut 72" diameter Oil-Bath Bull Gears. (This is actually identical to an upgrade to Premier lathes still running.) -- Factory Hydraulic Backup Roll. (This backup roll rides on adjustable rollers riding down on top of the carriage. This prevents the backup roll from pushing excessively hard against the core. It produces perfect 4" cores).Equipped with: -- DURAND Charger and Pumps (self-centering). -- Factory Log Deck - Complete with S-drive and Gearbox. -- Factory Air Trash Gate, Infeed Conveyor (infeed to chipper). Infeed to PRENTICE Air Bag Clipper, Timing Wheel and Holddowns. -- Factory 5' Wheel, 6-knife, Veneer Chipper with Hold-down Drum Roller, and S-drive complete. -- 6' FERANO Chip Screen and Conveyor. -- Steel Framework and 450 FPM plus unwind speed!Highlights & Background: -- This lathe is capable of peeling very high production. In 1967 it was regularly peeling 225,000 sq. ft. 3/8 basis, or 400 - 500 cubic meters per 8-hour shift. The lathe is in wonderful overall condition and portions can be turned on today although it has not seen service since 2005. When you think "CARGATE" think "big PREMIER" and you will have the right idea.Price shown is in US Dollars. - Experienced Owner is flexible to assist in removal and perhaps installation.

CARLSON CD PINNER PLUS Cabinet Door Clamp & Pinner; 30" Wide x 48" High max. Capability. The ProMax Cabinet Door Pinner is an affordable system that squares, clamps and fastens a variety of cabinet door styles and sizes. This machine is designed to handle stile widths between 1-1/4" and 3-1/2" in 1/8" increments and any rail widths. Standard product minimum: approximately 7" wide X 6" tall for 2" stile and rail cabinet doors. Standard product maximum: approximately 30" wide X 60" tall for 2" stile and rail cabinet doors.General Specifications: -- Standard joy stick operation allows quick and accurate size adjustments. -- The frame is ergonomically designed at an angle for easy placement of sub-assembled door parts and fast removal of the finished product. -- Operating controls are simple and convenient to minimize training time. -- Machine functions are air powered with programmable electrical controls for accurate and reliable operation.Includes: -- Air motor drive system. -- Standard clamp pads. -- Cope & Stick door fastening. -- Spare tool assembly. -- Size upgrade - Height 60". -- Miter capability. -- Safety light curtain. Features: -- Heavy duty frame, low maintenance, powered size adjustments, precision linear bearings, overhead mar-proof clamping, programmable controller.

CAROLINA BLOWER Size 80-6 Material Handling Fan with Motor. --Specification: -- Can handle approx 35,000 CFM @ 11" SP and 840 RPM. -- Comes with: Westinghouse Life-Line (high efficiency) 125 HP, 405T frame, ODP Motor complete with pulleys.. -- Motor is not mounted on base. -- Actual Model is 80-6SD.

CAROLINA BLOWER 45-6 Standard Duty Fan/Motor package assembled complete 30 HP motor. -- Rated at 8,860 CFM at 10" SP. Fan inlet diameter is 19". -- Fabricated with 3/8" thick wheel blades, 1/4" thick housing, primed and painted beige. 30 HP TEFC motor. Unitary base, V-belt drives, shaft, and belt safety guards. -- This is an Industrial Material Handling fan with paddle-wheel construction. Also available in Heavy Duty version at extra cost, with thicker scroll-housing to handle airborne smaller solid wood or similar material.

CASADEI FLEXA 27 RMA8 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:FLEXA 27 RMA8: CA1297 Standard equipment: Electrical data: E-Stop on main control panel: 230 V – 3 Ph – 60 Hz. 37 Amps. -- Equipped with:CA2074 Anti-adhesive Unit “RA"; to avoid glue deposits on top & and bottom surfaces. -- Kit for “NESTING"; processing. -- CA4048 Spray Mist Device for edge finishing improves panel. -- Cleaning and polishing of the applied edge. -- Welded Steel Frame & Steel pressure hold-down beam with (2) rows rubber rollers. -- Feed chain with industrial high grip rubber. -- Chain on hardened steel guides. -- Guides consist of one circular and one flat. -- Manual adjustment of the pressure beam w/ readout. -- Automatic pos. of the working units w/ reference to panel. -- Mechanical digital indicators for panel thickness. -- High Frequency Motors w/ Inverter. -- Centralized dust extraction. -- Adjustable panel support rollers. -- Sound enclosure & lockable switch cabinet -- Working Units:Glue pot and edge processing magazine. -- 2-Motor end trimming Unit. 0 - 15 deg. -- 2- Motor Top and bottom trimming unit. -- Edge scraping unit for 3mm. -- CA5695 Glue Scraping Unit “GS/K2". -- CA9360 Brushing/ Buffing Unit “BFK";. -- Machine Features:• Guided by a chain for accurate feeding and long lasting perfection • Thick, Steel top pressure beam complete with two rows of rubber coated wheels.• Robust panel support which can be extended according to the size of the parts MEGA 120 Controller• Ergonomic positioning• 4";Graphic Display w/ multi language selection • Glue temp. control w/ temp • Unit operation and feed track start/ stop• Digital readouts • Parameter/ setting control • On board diagnostics • Partial and absolute statistical info: # of pieces worked, edge used and feeding information Pre-milling unit • Two cutter heads with automatic timing • Independent high frequency motors with Stock removal determined by infeed fence with digital display • Timed blower to clean the machined surface • Diamond tools 2.4 HP each. Tools D=100mm H=49mm Max stock removal is H=45 mm / 55 mm • ²Nesting Kit Allows processing of predrilled parts • 3 contacting rollers on Trimming Unit • Edge Scraping Unit • Rubber coated copy wheel for end trimming unit • Anti- Adhesive Unit RA • Perfect cleaning of the panel • Prevents glue from sticking to the top and bottom surfaces GP-200 • Two Pressure rollers (1 large, 1 flat) • Teflon coated glue pot• Automatic glue temperature regulator to reduce glue temperature if machine is not in use to reduce glue heat time• Automatic recovery of glue • Automatic loader for strips • 2.4 kW. 3.3 HP Power. 1.5 Kg Capacity End Trimming Unit IK/200 • (2) Independent high frequency motors w/blades • Pneumatic tilting of the saw blade 0 – 15 deg. from control panel • Units slide on THK guideways • Mounted to the base for vibration-free machining• 12,000 RPM and .3 HP each. Trimmin

CASADEI/SCM FLEXA 37 EDGEBANDER WITH CORNER ROUNDINGEdge material thickness 0.4 - 3 mm coil & 6 mm (1/4") strips ~ min/max panel thickness 8 - 60 mm (0.31 - 2.36") ~ min. panel width, 80 mm (3.1") and 140 mm (5.5") min. length.Equipped with: Automatic coil & strip feed magazine, with Heavy Duty 3 mm PVC cap. guillotine. Gluing Unit "GP-300", teflon coated quick change glue tank, approx. 10 minute heat-up time, programmable temperature control w/timer if machine idles to prevent glue overheating/burning.Side Pressure Unit: 3-roll pressure unit w/1st roller power driven via clutch with pneumatic in & out positioning, (2) idler rollers.Workstations: -- End Trimming: -- Front & rear end trim (2 x 0.3 HP - 12,000 RPM motor ea.), with pneumatic tilting feature (0° - 15°) from control panel.Top & Bottom Trimming. -- Combination flush/bevel/radius trimming (2 x 0.65 HP - 12,000 RPM ea. motor). tilts from 0 - 25°. Pneumatic 3 position pre-sets programmable from control panel. -- Corner Rounding station. -- Top & Bottom PVC Scraper for up to 3 mm radius. Programmable, pneumatic exclusion on/off. --Top & bottom buffing unit (2 x 0.2 HP - 1,400 RPM motor each), Tlting range 8°

DIEHL ESL-10 Straight Line Rip Saw, with Laser Specifications: Table size 39-1/2" x 52" x 35" H. Throat 17-1/2". Distance from front of blade to table 21-1/2". Max. blade dia. 16". Max. thickness 1-1/2". Guaranteed glue joint length 48". Feed speed 30 FPM. Equipped with: 10 HP Blade motor with Automatic brake. Pyramid corrugated feed chain, with 1 HP Motor. (5) Pairs of 2-1/2” Dia. x 1-1/2” W Hold-down rolls. 20-1/2” L x 2” H Fence. Upper & Lower anti-kickback fingers. Manual feed chain lubrication. Complete with: Installation, Maintenance & Operating Instructions. Laser. 11-3/4" Dia. Blade. (4) Swivel Casters.

DIEHL STRAIGHT LINE RIP SAW SL30-19 Specifications: -- 10 HP Motor - 3,450 RPM belt driven fixed arbor, 14" - 16" blade dia., 2-1/2" max. thickness; 1.5 HP - 1,800 RPM feed drive, single fixed feed speed of 60 FPM. -- 19" Throat depth to right of blade, 18" of table to left of blade, 56" long table, cast iron pressure bar arms with ball bearing rollers, 60" guaranteed glue joint accurate. -- Multi-V, fully machined, pyramid corrugated single feed chain.Complete with: -- Adjustable rip fence, self-adjusting upper anti-kickback fingers with cam height control & lower anti-kickback fingers in table. -- Pressure beam outfeed guard with pivoting side pressure, automatic pneumatic lubrication of feed chain & race. -- Full overload & under voltage protection. -- Automatic brake for arbor protection, and pressure bar curtain. Options: Diode laser & mounting bracket; 15 HP motor, 20 HP motor.

15 HP Motor - 3,450 RPM belt driven fixed arbor, 14" - 16" blade dia., 2-1/2" max. thickness; 1 HP - 1,800 RPM feed drive, variable feed speed of 50 - 140 FPM. -- 19" Throat depth to right of blade, 18" of table to left of blade, 56" long table, cast iron pressure bar arms with ball bearing rollers, 60" guaranteed glue joint accurate. -- 1.5 HP feed motor, Multi-V, fully machined, pyramid corrugated single feed chain. -- Complete with: Adjustable rip fence, self-adjusting upper anti-kickback fingers with cam height control & lower anti-kickback fingers in table, pressure beam outfeed guard with pivoting side pressure, automatic pneumatic lubrication of feed chain & race, full overload & under voltage protection, automatic brake for arbor protection, and pressure bar curtain. -- Options: Diode laser & mounting bracket, please add ...$ 1,195; 20 HP motor, add ...$ 1,365.