TYLER 2400 SLAT-WALL MACHINE: -- Specifications:Produces T-slots "Slat-Wall" for architectural/store fixture panels.48" x 97" Max. panel capacity., 24" x 24" min. cap., panel thickness 0.5" to 1.5". Machine capable of processing up to (40) panels/Hr, depending on material density, thickness and the slot profile. -- Equipped with:This machine is currently set up with (18) router spindles on 3" centers,Spindles are driven in groups of (3) with (6) 7.5 HP - 3,450 RPM motors that drive the (18) router spindles, all router spindles rotate @ 15,400 RPM.This machine can accept up to (21) router spindles & the additional spindles can be activated by adding (1) additional 7.5 HP - 3,450 RPM motor. -- Machine Operating Sequence:Panels remain stationary on top, pneumatically clamped in place while the bottom mounted router bank traverses the full length of the panel with a high-speed return,Variable feed speed control, router assembly traverses on ground & polished rails with chain drive.Panels are positioned along the 8' rear edge fence line, distance from the panel edge to the centerline of the 1st cut can be adjusted from 0.0" - 3" (1 router spindle pitch). -- Operator & Machine Control:Allen Bradley electrical controls for the machine cycle and a "setup" mode of operation.Machine cutting cycle is initiated by a 2-hand operator safety buttons located on the right front of machine. -- Complete with:Overhead hold-down assembly with (2) large air cylinders and (6) arms with spring loaded clamping pads hold the panel in place.Panels are loaded from the 8' front and exit to the side for easy unloading. -- Options Include: An assortment of used "Diamond Tooling" (diamond router bits) An assortment of extra motors spare parts service manual & docs. -- Actual Model is TYLER 2400

TYLER 703 Power Pod Cold PressTyler Air Pod Press with a Platen dimension of 40″ Wide X 87-1/2" Long. -- The Maximum Daylight Opening is 49.5″, and the pods will extend 9.5″ for a minimum opening of 40″. -- The top and bottom plates are dent free. -- The press is rated to 100 PSI and has (1) pod short of 100% pod coverage (being that the center bags are staggered). -- There are spring loaded bed rollers to aid in loading and unloading. .This machine has been cleaned and checked and there are no air leaks.

UAS -BHT (CALCOR) MIB-11-T19- SVA Pulse Jet baghouse dust collector. MIB is Modular Industrial Baghouse. -- Has qty (18) each of filter cartridge # 04007500 (6.125 x 75") and qty (18) each of filter cartridge # 0400000249 (6.125 x 41.6250"), for a total 1,896 sq. ft with pleated Spunbonded Polyester w/PPTFE filter bags. -- OEM rated for 5,000 ACFM @ 11" SP, resulting in a 2.64 Air-to-cloth ratio. -- 20 HP Siemens motor, on a large floor-mounted blower -- Comes with DPC and Timer board for Pulse Cleaning Control. Allen Brady Starter and air quality motoring. -- Discharges thru Pyramid hopper into a 55 Gallon Drum. Includes dome style explosion vent.. -- Housing dimensions: 60" x 60" x 232" high. Total weight with filters: 3800 Lbs. -- Looks like its brand new. -- Last used for a CNC Laser Cutter.

UHLING HP2000 Case Clamp (Pneumatic)Offers a compact, quick and easy-to-use Case Clamp.Specifications: -- 50" x 42" x 24" Clamping cap. that can handle 80% - 90% of your case good needs. -- (2) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks. -- Single lever lock or unlock control and front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access operator's control panel that is mounted on the vertical beam.

UHLING - HP 2000: Case Clamp (Pneumatic) Specifications: -- Offers a compact, quick, and easy-to-use Case Clamp. -- 50" x 42" x 24" Clamping cap. that handles ...80% - 90% of your case good needs. -- (2) Counterweight-balanced, fully adjustable horizontal dual air pod pressure bars. -- 3-1/2" Stroke with: Individual controls for each air pod pair. -- Roller bearing mounted carriage with: Pneumatic locks. -- Single-lever lock or unlock control; front/rear pressure selection. -- Solid panel counter support opposite to pressure bars. -- Easy Access Operator's Control Panel that is mounted on the vertical beam.

UHLING - HP-3000: Case Clamp (Single-Bay) -- SpecificationsClamping capacity: 72" L x 74" H x 24" D; Large enough for multiple boxes; offers versatility, quick 30-Sec setup or changeover. -- Pressure Elements(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; just position them effortlessly and let go: Counterweight will keep them in place; no need to secure them! -- Air Pod Stroke3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical BeamMoves easily on roller bearings; pneumatic carriage locks with: (4) Small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam so it is always where it is needed; single lever lock-or-unlock control & front/rear pressure selection. -- Counter SupportBy solid laminated panel opposite to pressure bars. -- Actual Model is: UHLING HP-3000

UHLING HP-3000 CASE CLAMP (SINGLE-BAY): --Specifications:Clamping Capacity: 55" L x 96" H x 24" D; large enough for multiple boxes. Offers versatility, quick 30-second setup or changeover. -- Pressure Elements:(4) Dual air pod pressure bars that are pneumatically activated; counterweight balanced; position them effortlessly and let go. The counterweight keeps them in place; no need to secure them! -- Air Pod Stroke:3-1/2" Stroke of air pod with 0 - 120 PSI pressure adjustment. -- Vertical Beam:Moves easily on roller bearings with pneumatic carriage locks; (4) small air cylinders from (1) control point. -- Operator Control Panel:Mounted on vertical beam, so it is always where it is needed; single-lever lock-or-unlock control & front/rear pressure selection. -- Counter Support by:Solid laminated panel opposite to pressure bars.

UHLING HP-3000 Case Clamp ... offers versatility, quick (30) second set-up or changeover. -- Clamping Capacity, 55"- L x 96"- H x 24"- D, that's large enough for multiple boxes. -- Pressure Elements, (4) horizontal @ with (3) individual air pods, counter-weight balanced, position them effortlessly and let go, the counter-weight will keep them in place, no need to secure them! -- Air Pod Stroke, 3-1/2" with individual controls for each air pod set. -- Vertical Beam, moves easily on roller bearings with pneumatic carriage locks. -- Operator Control Panel, mounted on vertical beam, so it is always where it is needed, single lever lock-or-unlock control & front/rear pressure selection. -- Counter Support, by solid laminated panel opposite to pressure bars. OPTIONAL: Top Clamping, removable top pressure element for applications such as a vertical center partition or similar needs, removes easily if not needed. Add $ 1,000.00 to standard machine price.CUSTOM:HP-3000 F, ... comes with a "Solid Floor" for easy clamping of upper cabinets, add $ 1,000.00 to standard machine price.HP-3000 M, ... clamping capacity, 60"- L x 96"- H x 36"- D, that's large enough for deep commercial Case Goods. Please call for pricing.

UHLING HP 4000 Case ClampThe most versatile, quick and easy-to-use Case Clamp on the market!Specifications: -- 100" x 50" x 24" Clamping cap. that's UHLING's most versatile Clamp ever. -- (3) Counterweight balanced, fully adjustable horizontal dual air pod pressure bars and (2) vertical, easy adjustable dual air pod pressure bars. -- 3-1/2" Stroke with individual controls for each air pod pair. -- Roller bearing mounted carriage with pneumatic locks (considered to be the fastest 2-axis Clamp on the market). -- Single lever lock-or-unlock control and front/rear pressure selection. -- Solid panel counter support that is opposite the pressure bars. -- Easy access operator's control panel that's mounted on the vertical beam. -- Approximately (30) Sec or less changeover time. -- Options: Additional dual pod pressure bar assembly for vertical or horizontal.

AAF PULSE-PAK 21-3H Pulse-Jet Cartridge Dust Collector. (3H) is three-high filter elements. (21) is the total number of Panel Pak V's.The Panel Pak filter element has two flat panels of pleated media in a Vee-Configuration allowing installation and change-out with minimum time and effort. Each cartridge has its own gasket ensuring a positive, air tight seal. -- Consists of two modules: one containing (9) 3x3 filters and the second contains (12) 4x3 filter cartridges, for a total of (21) cartridges. -- Housing dimensions: 191.75" High (with 48" hopper clearance), 104.25" Wide, 94.25" Depth, and Weighs about 6,400 Lbs. -- Air consumption about 6 cubic feet/hr. at 90 PSI of clean dried air. -- Fan and Airlock available at extra cost. please inquire.

ACCE - Tire BalerSpecifications -- 30 HP Motor. -- Overall Dimensions - 18' x 16-1/2' X 12-1/2'. -- 13,000 Lbs. -- Dual Cylinder.

ACT 3-12 Cartridge Dust Collector Cartridge style downflow dust collector rated at 4,000 CFM @ 13". Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 15 HP rated at 4,000 CFM. @ 13" -- (12) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 1,200 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 15HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 16" inletEquipped with: -- TCBI 15 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (6) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 24" x 36" explosion relief panel. 5.72 sq ft vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with 1 heat trace kit for cold weather installation. -- 14" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 14' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 21'. -- Custom - Explosion Isolation Valve, 16" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 24' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USA?Photo does not represent the actual model

ACT 3-24 Cartridge Dust CollectorCartridge style downflow dust collector rated at 8,000 CFM. Heavy-duty with 7 and 10 gauge construction. Specifications: -- Blower, 25 HP rated at 8,000 CFM @ 12" -- (24) Poly-Elite, spun-bond polyester media with 100 Sq. Ft. of media per filter filter (total 2,400 Sq. Ft.) that are 99.9% efficient. -- Reverse pulse filter cleaning system. -- 25HP All-in-one starter/disconnect/timer board/digital pressure gauge 460V 3ph -- DK-XP – explosion rated drum kit with quick-lock easy-access filter doors. -- 18" inletEquipped with: -- TCBI 25 HP Blower with direct drive, top mount. -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (12) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Return Air Includes: -- Shut off landing spot in control panel for explosion isolation valve. -- Explosion Vent installed with hardware, 36" x 36" explosion relief panel. 8.63 Sq. Ft. vent area. Domed for durability. KST value required. -- Sprinkler coupler for collectors with 1 module. -- Solenoid heater kit with (2) heat trace kits for cold weather installation. -- 18" VF - Explosion Isolation Valve Assembly (dirty air to dust collector), Must be installed between 16' and 55' from the dust collector inlet. If an elbow exists, minimum distance is 24'. -- Custom - Explosion Isolation Valve, 20" VF - Explosion Isolation Valve Assembly (clean air return to building). Must be installed between 19' and 55' from the dust collector outlet. -- 10 year workmanship and materials warranty -- Made in the USAPhoto does not represent the actual model

ACT 3-6 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 4,000 CFM. Specifications: -- Blower, 10 HP rated at 4,000 CFM @ 10" w.c. -- Holds (6) Nano Elite, merv 15, cartridge filters with up to 1,524 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter panel. -- (6) Filter Upgrade to ACT Nano-Elite, flame-retardant, Nano-Fiber media with industry best Merv 15 efficiencyEquipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (3) pulse valves. Goyen solenoids and diaphragm. -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. -- 12" in-let. -- Silencer for TCBI 1010 year manufactures materials and craftsmanship warranty . Made in the USA

ACT 4-16 Cartridge Dust Collector Cartridge style downward flow dust collector rated at 8,000 CFM. Specifications: -- 20 HP Direct drive, top mounter blower rated at 8,000 CFM @ 10" w.c. -- (16) Nano Elite, flame-retardant, Nano-Fiber merv 15, cartridge filters with up to 4,064 sq. ft. of filter media that are 99.9% efficient. -- Pulse control timer board with built-in digital pressure gauge. -- Drum lid with latch kit, quick-lock easy-access filter doors. -- Magnetic motor starter.Equipped with: -- Automatic reverse jet cleaning via compressed air, (1) pulse valve per (2) cartridges for a total of (8) pulse valves. Goyen diaphragm and solenoid valves -- Heavy Duty steel legs position unit approximately 4' above the ground made with 7 and 10-gauge construction. Options: -- Fan outlet damper. -- Fan outlet silencer. Other models available, please check with the Product Manager10 year workmanship and materials warranty -- Made in the USA

ADVANCE LIFTS P-6036+M Scissor LiftThe P-Series lifts are Advance Lifts most popular series as they fit a wide array of manufacturing applications.SPECIAL FEATURES & BENEFITS: -- These units are equipped with the patented “Platform Centering Devices";, which doubles or triples lift life. -- All of the controllers are Underwriter Laboratory listed assemblies. -- These units are fully primed and finished with a baked enamel finish. -- The cylinders are machine grade with clear plastic return lines. -- All pressure hoses are double wire braid with JIC fittings. -- The reservoirs are mild steel. -- These units conform to all applicable ANSI codes.Specifications: -- 6,000 Lbs. capacity. -- Platform size 36" x 72" (Min. Platform Size: 24" x 48" Max. Platform Size: 48" x 72") -- Max. End Load Capacity 4,100 Lbs. -- Max. Side Load Capacity: 3,500 Lbs. -- Baseframe Size: 24"" x 48". -- Lowered Height: 6.5". -- Raised Height: 42.5". -- Approx. Speed Up: 27 sec. -- Internal Motor: 2 HPWarranty 10 Year Structural / 250,000 Cycles - 1 Yr Parts and Labor

AES SIRIUS 950M ATC CNC MACHINING CENTER (FEED THRU): -- Specifications:Automatic CNC feed through Point to Point Boring Machine that combines flexibility and high productivity.A perfectly suited solution for small to midsize companies & artisans in need of an automatic solution for precision drilling with a low cost investment.Parts can be discharged at the opposite end of the machine for automated material handling or returned to the Operator for manual unloading. -- Working Capacity:Max. panel size on X-Axis is unlimited; Y-axis is 37.4" (950 mm); Z-axis is 2-3/4" (70 mm).Min. panel on size X-axis is 9.84" (250 mm); Y-axis is 3.14" (80 mm); Z-axis is 0.31" (8 mm). -- Positioning Speed: Panel feeding speed of 229 FPM (70 MPM); Y-axis at 229 FPM (70 MPM); Z-axis at 65 FPM (20 MPM).Axes positioning by AC drives & brushless Servo motors; the Panel moves in X-axis & the boring head moves in Y & Z-axes. -- Work Area:NC Controlled "Optical Material Sensor" creates a zero-panel reference point by reading the panel ends; this ensures that RH & LH (mirror image) panels will always be symmetrical.High precision clamping automatically positions the workpiece. Automatic presser moves independently and adjusts to workpiece thickness. Pneumatic side pusher make locating workpiece accurate and efficient. LH Side pressure clamp with automatic adjustment & pneumatic locking according to the panel width.Scratch resistant air floatation tables make for ease of loading and unloading from either side of the machine. -- Boring Unit:HSD Drilling head; 3 HP (2.2 kW), variable speed from 4,500 - 8,000 RPM motor. (10) Independent vertical spindles on 32 mm centers; (5) spindles in X-axis & (5) spindles in Y-axis.(6) Horizontal spindles with (2 + 2) in X-axis & (1 + 1) in Y-axis.(1) X-Axis grooving saw for max. 120 mm dia. blade; variable speed from 5,500 - 10,000 RPM. -- Machining:HSD 7 HP (5.5 kW) spindle; variable speed from 1,000 - 18,000 RPM with manual tool change system.(1) 6-Position ATC Automatic Tool Change system with ATC rotary magazine. -- Operator & Machine Control: PC Based user-friendly, icon-driven control housed on the main machine base; displays programming graphics, functions, and machine data. -- Complete with: Users & Maintenance Manuals; ALPHACAM "Essential" is provided with machine for ease of programming at the Controller. -- Software Disclaimer:EX-FACTORY INC. offers NO warranty or support, written or implied concerning any/all "optional" or "additional" manufacturer or 3rd party software supplied with this machine. All software related issues including re-licensing fees/requirements/functionality & training is ultimately the sole responsibility of the "Buyer".Actual Model is: AES SIRIUS 950M - ATC

AGET 20SN5157 Cyclone with FT-40 Baghouse2,300 CFM at 9.3" SP; 5 HP Top-mounted blower motor cyclone, 8" inlet dia.,10" outlet diameter. -- Dust particles are pulled through the cyclone with larger particles dropping through the cyclone to dump into collection bin. Finer particles are forced through the Baghouse to filter the remaining air.. -- Includes; 5 HP LEESON ELECTRIC TEFC top-mounted blower, cyclone, AGET "FT-40" Baghouse after-filter, manual slide gate opening and automatic bag shaker which comes on after shut down of collector. -- Interior bag house with (40) 5" dia. x 8' L cloth tubes, total filter area of 383 sq. ft. The larger dust particles are pulled through cyclone into (2) 55-Gal barrel storage with manual slide gate opening at bottom.

AIR CURE 484RF10 Dust Collection System with Rotary Air Lock and Abort Gate.Specifications: -- Filter area capacity 56,000 CFM @ 9:1 Air to Cloth Ratio (ACR), approx. 13'- 2" dia. round baghouse; -- (484) Cloth filter bags of 10' length (3" x 6") oval bags provide for radial movement of bag during cleaning for longer life), 6,180 sq. ft. of filter area. -- Designed for filtration media cleaning via 7.5 HP approx.on board rotary air pump for compressed air operating at about 7.5 PSI. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Rotating cleaning air manifold driven by 1 HP motor, (1) NEMA IV timer & solenoid/diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. Includes: -- Supplied Fan: ALLIED BLOWER & SHT MTL. SIize: 90 MH fan, 38" inlet dia, with paddle wheel blades powered by 250 HP TEFC motor, ground mounted . Note1: This fan is very versatile as it can operate from 10,000 CFM @ 6" or 7" of water SP all the way up to 40,000 CFM @ approc. 14" of water SP depending on RPM chosen. To be conservative one would keep the upper end to around 1,000 RPM. Motor could be 25 HP or 250 HP at these extremes. Being a radial blade fan it is capable of handling most materials. -- Note 2: Depending on application there is filter area capacity to add another Fan/motor for about 16,000 CFM (as per above). -- Explosion doors; walk-in access door on platform at access door. approx. 18" Rotary Air Lock (RAL) and about 38" Abort Gate with separate support stand and access platform.Features: -- 10-Gauge shell all-welded construction, Tangential scroll inlet and Inlet deflector baffle. -- All cages are unbolted to minimize damage and left in the shell. Bags are removed (to reduce weight on cages) and crated - will likely need to be laundered. -- Actual AIR CURE model is 484AC10. -- Note: Upon installation buyer is responsible for compliance to all applicable NFPA or local, state or Federal codes.Transportation also available at extra cost.

AIR CURE 484RF8 Pulse Jet dust Collector.. -- Overall Specs: 30,000 CFM @ 6.1:1 Air-to-cloth ratio, 158" dia. round baghouse with a capacity of (484) cloth filter bags (Bags not Included) of 8' length (3" x 6" oval bags provide for radial movement of bag during cleaning for longer life), 4,900 sq. ft. of filter. -- Designed for filtration media cleaning via 7.5 HP on board rotary air pump for compressed air operating at about 7.5 psi. Return air outlet and approx. 48" x 48" inlet for dust laden air. -- Filter cleaning: Rotating cleaning air manifold driven by 0.33 HP motor, (1) NEMA 9 solenoid and diaphragm valve control pulse jets of air to clean each row of bags; galvanized steel bag frames with positive bag bolt down to eliminate leakage and ride up of bags once installed. -- Includes: AEROVENT (TWIN CITY) model 330, type CBA-SW Class 4 Backward Inclined Air Handling Blower, Arrangement 9 with 100 HP TEFC motor; Explosion doors; walk-in access door on platform at top and safety ladder. -- Original cages will be removed and stored separately from the filter. Unique skirt at bottom of cyclone thus no support steel is needed and facilitates anchor bolt installation. -- Depending on application/desired air capacity it can be increased to about 44,000 CFM (@ 9:1 to Air-to-Cloth ration) but to do so will require slightly larger fan/motor. -- Needs new bags as they were discarded.