GIBEN MATIC 401 SPT REAR LOAD, AUTO. PANEL SAW: -- Specifications:157" (4,000 mm) Overall rip cutting capacity; 5.9" (150 mm) max. saw blade projection;30 HP (22 kW), 2,934 RPM Main saw motor, 22.2" (565 mm) dia. main blade;2.4 HP (1.8 kW), 6,095 RPM Scoring saw motor, 7" (180 mm) dia. scoring blade. -- Saw Carriage:Travel speed 3 - 230 FPM (1 - 70 MPM), 230 FPM (70 MPM) constant return, powered by Inverter drive. -- Pusher Fence:Programmable pusher fence with (10) material gripper clamps (clamps open to 6.3" / 160 mm); Pusher speed 1 - 98 FPM (1 - 30 MPM), return 230 FPM (70 MPM), powered by AC Servo motor on Rack & Pinion system. -- Operator & Machine Control:PC Controller with Windows + Giben "G-DRIVE 2D" operating system; 17" color monitor. Parametrically controlled saw carriage automatically adjusts the cutting speed when cutting narrow trims front-and-back. Editing feature allows programming during operation, downloading from remote PC to the machine controller is possible. -- Rear Load Lift Table:7’ x 13-1/2’ x 18-1/2"; H 4-Column rear load lift table; max. panel size 157" x 63" (5,700 x 1,600 mm);Lift table stroke 31.5" (800 mm); max. stack height without pit or risers 27" (680 mm);Raise & lower speed 2.3 FPM (7.5 MPM); (2) material front aligners located behind the cut line. -- Complete with:(5) Air floatation tables 79" x 20" x 48-1/4" H (2,000 x 510 mm); 62-1/2"; L x 6-1/4"; H Front & Rear fences; Modular rear machine table with non-marking rollers on rails; 5’ x 13-1/2’ x 18-1/2"; H Infeed conveyor with 40-1/2"; H Back stop;(2) Pneumatic side aligners w/automatic pre-positioning by "G-Drive" control, Aligner stroke 2.25" - 87" (70 - 2,200 mm), minimum material width 3.9" (100 mm).Front safety flaps on the pressure beam; rear & side of machine provided with protective guards.6,000 Lb. Cap 48" x 96" Electric/Hydraulic Scissor Lift Platform, with Raised height (Platform surface) 48", Lowered height (Platform surface) 11", 3/4 HP - 1,725 RPM Hydraulic motor, & (4) 3" x 3" Steel tubes welded to platform surface.Actual model is GIBEN MATIC 401 SPTNOTE: Saw carriage servo motor & Axis control card are both inoperable and need to be replaced.

GIBEN SMART 75 SP FRONT LOAD, AUTOMATIC PANEL SAW: -- Specifications: 149" (3,800 mm) Overall cutting length, 131.8" (3,350 mm) pull back 2.95" (75 mm) max. blade projection.15 HP (11 kW) main & 1.5 HP (1.1 kW) scoring motor, 3,800 RPM main saw blade & 6,000 RPM scoring blade with external adjustment.. -- Saw Carriage:Variable saw carriage forward speed 16 - 164 FPM (5 - 50 MPM), return speed 197 FPM (60 MPM);Rack & pinion drive, driven by AC brushless Servo motors. -- Pusher Fence:Electronically controlled overhead program fence with (7) pneumatic gripper clamps, max clamp opening 2.56" (65 mm).Variable forward pusher speed 2.5 - 82 FPM (0.8 - 25 MPM), return speed 131 FPM (40 MPM);Pusher driven on round bar-ways by AC brushless Servo motors. -- Operator & Machine Control:PC front end with Windows "XP" + "Pentium" processor operating system with multitasking & easy programming of very complex cutting patterns.15" CRT monitor displays REAL-TIME graphics of cutting dimensions & patterns, program cutting list, manual cuts, diagnostic & on-line help.Data input by adjustable key pad pendant, standard industrial keyboard & mouse & CD-ROM drive; direct downloading from office PC is possible."Moeller" PLC guarantees full management of all machine movements (pressure beam, saw carriage and side aligner pusher positioning, etc.).The numerical control adjusts the optimum saw blade projection for the stack of panels being cut and sets the most appropriate cutting speed, in relation to the stack itself, and when necessary to the width of trim cut too. -- Rear of machine:(9) Rear support rails with 80 mm dia roller modules; rear of machine enclosed for safety. -- Front of machine:Automatic side/crosscut aligning device with 2.4" - 48" (60 - 1,220 mm) stroke. 90" (2,300 mm) Long crosscut fence (front-to-back);(1) Front mounted air floatation table 20" x 78" (510 x 2,377 mm) & (3) Front mounted air floatation table 20" x 60" (510 x 1,524 mm). -- Complete with:G-Lock "Quick Change" saw blade system. -- Actual Model is GIBEN SMART 75 SP

GIBEN G2 GENESIS 48 CNC ROUTER (ATC & BORING): 4' x 8' Fixed table; moving gantry machine with: Single zone vacuum table. -- Equipped with:(1) 12 HP ISO-30 Type ATC spindle; air-cooled; ceramic bearings; variable spindle speed from: 6,000 - 24,000 RPM. -- 6-Station Automatic Tool Changer & 2 HP 9-spindle vertical drill bank (5 in X- & 4 in Y-Axis). -- Axis Stroke1,300 mm (51") In Y-Axis; 2,500 mm (98.4") in X-Axis; 200 mm (7.8") in Z-axis. -- Max. Feed Rate60 MPM (2,362 IPM) In X- & Y-axis; 30 MPM (1,180 IPM) in Z-axis. -- FeaturesTool Length Measuring System (Tool Touch Off device). -- ControlANDI/SYNTECH Controller with: Network compatible WINDOWS PC based front-end; color monitor; keyboard; mouse.Full function handheld pendant absolute & incremental programming; cutter & tool length compensation; feed rate & spindle speed override; inch/metric operation; linear/circular & helical interpolation. -- Complete with:10 HP BECKER Vacuum Pump; Tool Holder’s collets; Light safety fences. -- Maintenance supplies: Grease, grease guns; full manuals; product literature.

GIBEN G4 512 CNC ROUTER (ATC & BORING): -- Specifications:5' x 12' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working capacity:X-Axis 145.6" (3,700 mm), Y-axis 62.9" (1,600 mm), Z-axis stroke is 9.8" (250 mm), max. material thickness 4.7" (119 mm). -- Positioning Speed:X- & Y-Axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM).X- & Y Axes use a precision Rack & Pinion system, Z-axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing".(2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; Automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, speed 6,000 RPM, "HSD" Boring unit.(9) Independent vertical spindles with: (5) in X-axis & (5) in Y-axis. -- Machining:(1) 15 HP/18 HP peak Air-cooled "ANDERSON" Electro-spindle with: HSK F63 Adaptor, RH & LH rotation; variable speed from 1,000 - 22,000 RPM.(1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control:PC Front End with ANDI/GIBEN "SYNTEC 21MA PC based Controller" + "WINDOWS" Operating System.19" LCD Flat screen monitor; Server, full keyboard, and mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. -- Complete with:(2) 250 cbm/Hr (9 HP) "BECKER" vacuum pumps, tool holders, Collets, tool changing stand and manuals. Automatic program update according to the tool length (touch-off probe).Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is GIBEN - G4 512. Machine footprint Floor area 472"; x 197";

GIBEN - KG-320, ...Edgebander (Compact)0.4 - 3 mm Edge thickness capacity min. panel width 80 mm; panel thickness 10 - 60 mm; variable feed speeds: 12 - 20 MP; electronic adjustment of the upper pressure beam.Equipped with: 2 KG Glue pot & adjustable pressure roll section with: (1) Driven roller and (3) idler rollers.Workstations -- 2-Motor end Trimming Unit. -- Top & Bottom radius Fine Trim Station. -- Top & Bottom Buffing Station.Complete with & Features: -- Programmable PLC Control. -- Sound cabin for all workstations. -- Adjustable outboard panel support.

HOMAG KAL 210 AMBITION 2260 EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Coiled stock min/max. Edge thickness 0.4 - 3 mm (0.016. - 0.118"), Strip material min/max Edge Thickness 0.4 - 6 mm (0.16 - 0.234"). -- Panel stock min/max. thickness12 - 40 mm (0.472" - 1.574"). Panel Over-Hang 30 mm (1.18"). -- In-feed Fence: Adjustable in-feed fence with manual digital indicator positioning. -- Pre-Milling Station: Two 3.0 kW (4.0 HP), 150 Hz, 9,000 RPM Motors; equipped with trimming column, (2) horizontal and cross slides with spindle adjustment, electro-pneumatic horizontal jump movement of the first motor;Includes electronic frequency inverter for control of motor speed and braking, two (2) dust extraction hoods, an air-jet panel blow-off device & SIKO digital counters for adjustments. -- Panel Pre-Heater: the Pre-heater brings the panel to an appropriate temperature for better adhesion; this is especially beneficial in cooler temperatures. -- Multi-Purpose Magazine: 2-Coil magazine expands capability by running coiled material & strips, magazine height adjustment allows for greater usage of varying panel heights by raising and lowering the magazine table, allowing the operator to center the panel on the edgebanding. -- Gluing System: (EVA - Hot Melt) QA 3 -Quick Melt Overhead Unit & heated roller applicator; digitally displayed thermostat for both upper and lower unit.34 mm Dia. Glue Roller allows for excellent control of temperature for optimum bonding results with individual adjustment for leading and trailing glue gates, lower melting unit equipped with automatic glue level control. Melting capacity: 12 KG/Hr (26 LBS/Hr). -- Pressure Section: Automatic pressure zone adjustment (Servo), (1) large 160 mm dia. driven & (6) 70 mm dia. idle rollers, pneumatic pressure control depending on edgebanding material used. -- WORKSTATIONSEnd Trimming Unit HL 81: 0.8 KW (1.0 HP) x 2 - 200 Hz, 12,000 RPM Motors. to cut excess edge on the front & back of the panel; pneumatic adjusting from chamfer 30° to straight cut. -- Top & bottom Flush Trimming Unit: Top & bottom, 0.4 kW (0.74 HP) x 2 - 12,000 RPM Motors; Height adjustment with the top pressure-beam and tilting range +/- 1°. -- Profile/Bevel/Corner Rounding Unit FF 12: Multi-function 0.4 KW (0.54 HP) x 2 - 12,000 RPM Motor to fine trim the edge overhangs at the work-piece upper & lower edge, as well as trimming around the front & rear vertical edge. Max. feed speed 20 MPM (65.6 FPM) -- Profile/Bevel Scraping Unit PN 10: Top & bottom for thick PVC/ABS, pneumatically activated/adjustment. -- Flat Glue Scraper Unit: Top & bottom, pneumatically activated to remove potential glue squeeze-out. -- Buffing Unit FA 11: Top & bottom edge buffing/polishing, pneumatically activated. -- Operator & Machine Control:HOMATIC PC 22 Power Control w/Touch Screen: Controller functions in Windows environment and features: Keypad w/LCD flat-screen display, fault diagnostic, OS9 real-time operating syst

HOMAG DRILLTEQ V-200 CNC MACHINING CENTER (VERTICAL/W/BORING): -- Specifications: Flexible "Vertical" Machining Center with "BORING": Uses less than 5 sq. meter of valuable floor space in addition to an innovative panel handling system. -- Working Cap.Max. workable part size for "X" axis is 120" (3,050 mm); "Y" axis 33.4" (850 mm); max. part thickness 3.1" (80 mm).Min. worktable part size for "X" axis is 7.8" (200 mm); "Y" axis 2.75" (70 mm); min. part thickness of 0.31" (8 mm). - Automatic infeed & outfeed from the LH or RH side. -- Positioning SpeedThe "V-200" can reach movement speeds of 164 FPM (50 MPM) in "X" & "Y" axis & 50 FPM (15 MPM) in "Z" axis with total safety, providing an unmatched working capacity. -- Boring Unit(1) 3 HP (2.3 kW); Variable speed from 1,500 - 7,500 RPM motor; (13) independent spindles with: (8) spindles in "X" axis & (5) spindles in "Y" axis.(6) Horizontal spindles with (2+2) in "X" axis & (1+1) in "Y" axis; boring block has "QUICK CHANGE" spindle system. -- Operator Interface:HOMAG "POWERTOUCH" + Windows + WoodWOP Operating System; "IntelCore 2 DUO" Processor.21" TFT Monitor; international keyboard, soft touch keypad & industrial mouse; RS-232 Serial ports, USB ports; (1) 1.44 MB floppy disk drive, (1) CD RW drive, modem, Ethernet connection.Real-time multitask processing; programs can be transferred via diskette or downloading by wire is possible. -- Complete with:Pneumatic part clamping devices; sound enclosure and complete set of safety devices. -- Options Include:(1) "X" Grooving Saw; 9,000 RPM, max. saw blade dia. 100 mm.(1) 12 HP (9 kW) Electro Spindle router with manual Quick-Change adaptor; variable speed from 6,000 - 24,000 RPM. -- Actual Model is: HOMAG DRILLTEQ V-200 OPTIMAT BHX 055.

Houfek Buldog 7-3M-1100-RRC 3 Head wide belt sander43" width cap, Roller / Roller / Combination-headHead Configuration1st Head – Rubber – 90 shore @ 200mm (7.9";) dia.2nd Head – Rubber - 90° shore @ 2000mm (7.9";) dia.3rd Head– Rubber - 45° shore @ 200mm (7.9";) dia. with adjustable platen.Specifications -- Sanding width 1100 mm 43" -- Work piece height 3-160 mm 0.118"~6.3" -- Sand belt size 1120 x 2620 mm 44" x 103" -- Conveyor feed speed 3~15 m/min 9.8~49 FPM -- Table motor 0.18 kW 1/4 HP Equipped with & Features -- Main motor 1st head 18 kW 24HP -- Motor 2nd head 15 kW 20HP -- Motor 3rd head 15 kW 20HP -- Voltage 460/3/60 -- Exhaust outlet (4) 180mm; (1) 100mm (4) 7"; (1) 4" -- CFM requirements 6700 m3/hr 3950 CFM -- Weight 3100 kg (approx) 6820 lbs -- Floor space 3885x1715x2260mm153"x68"x89"

HURST 600 HP Waste Fired Boiler; -- Specifications:Complete in-place system with the following features: -- Decommissioned July 2019. -- 150 PSI. (300 PSI max wp), -- 20,700 Lbs per hour. -- Fuel House, Boiler Building and all Controls -- System has been "pickled" to maintain tube integrity.

HURST - SERIES 45. Boiler: Natural Gas -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox. -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with: National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency. -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with: Factory pre-piped, wired, and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are Factory packaged with: Operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

HYDREX HPX410-5 Hot Press 160 Tons using (8) hydraulic cylinders, Five daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to nominal 4' x 10' (about 51" x 126"). -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 160 Tons of overall pressure -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- Platen size 1300 mm x 3200 mm (51" x 126") approx. Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 40 PSI specific pressure over the entire platen area; 54 kW heating power. Approx. 7.5 kW (10 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from floor with lower platen in the down position; Heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 27.500 Lbs. -- Optional: Extra Large Oil Heating Tank for Special Higher Temperatures if needed.

HYDREX HPX510-5 Hot Press 120 Tons with (5) Daylight openings. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x 10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick; -- (8) Hydraulic "upstroke cylinders", approx. 85 mm dia.; Rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure; 54 kW of heating power. 40 PSI specific pressure over the entire platen area; 4.5 kW (6 HP) hydraulic pump motor. -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Max Working height is 4"; Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 24,000 Lbs. -- Overall dimensions: 3,800 length (+610mm -boiler + 610mm -pump/tank) x 1,790 wide x 2,450 mm high.

HYDREX HPX48-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 4' x 8', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time, emergency pedal, and quad temperature protection device. -- (6) Cylinders (upstroke) -- 80 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 98" x 51" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (6) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 80 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4 KW (5.5 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from the floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Overall press weight is approx. 12,500 Lbs). Overall dimensions 129" x 65" x 102" high.Also available with (3) openings - 100 Tons and (5) openings - 100 Tons.

HYDREX HPX510-1 Hot Press, Single daylight opening. Suitable for laminating veneer panels/doors, decorative paper, fireproof board, etc.Features (Overall): -- Board size up to 5' x10', -- Front Controls for easy setup & operating configuration, incl. temperatures and cycle time , emergency pedal, quad temperature protection device. -- (8) Cylinders (upstroke) -- 120 Tons of overall pressure, -- Recirculating Thermal Oil heated with package heaters housed in a boiler tank.Detailed Specs: -- 122" x 61" Thermal Oil heated Hot Press with drilled steel platens, 1.5" thick, 4" Max Working height.. -- (8) Hydraulic "upstroke cylinders", 85 mm dia.; rack & Pinion guide system for parallel closing of the platens. -- 120 Ton total pressure, 40 PSI specific pressure over the entire platen area; 4.5 KW (6 HP) hydraulic pump motor. Platen moving speed 5 FPM -- 1.5 kW (2 HP) Hot Oil circulation pump; approx. 120° C (248° F) max. operating temperature. -- Loading from (3) sides; 39-1/2" from floor with lower platen in the down position: heavy I-beam welded steel frame construction. -- "Safety" emergency Stop Cable around the operating sides of the machine, and E-STOP mounted on the control panel. -- Features: "Last" (2) cylinders can be turned off to press shorter panels. - Overall press weight is approx. 19,500 Lbs).

IMA ADVANTAGE 500 L EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Production Edgebander -- Specifications:Edgebanding capacity: Coiled material 0.3 - 3 mm (0.012 - 0.118"); strips 3.0 - 12.0 mm (0.118 - 0.472); panel thickness min./max. 8 - 60 mm (0.315 - 2.362").Equipped With:Premill Unit - 08.379 with: 4 kW x 2 (5.3 HP x 2) 9,000 RPM Vertical joining spindles, SIKO digital readouts, particle & debris air jet blower. -- Glue System - EVA (Hot Melt) with: "Quick-Lock" System. -- Pressure Section with: (1) Large dia. driven and (5) idle rollers. Workstations:End Trimming Unit - 08.415: Dual motor, 0.66 kW x 2 (0.88 HP x 2) suspended from the hold-down beam; automatic chamfer adjustment 0° - 8°. -- Rough Trimming Unit - 08.055: Top & Bottom flush trimming, W 1.0 x 2 (HP 1.34 x 2) - 12,000 RPM ea. motor; against the feed (up-milling), vertical & horizontal tracing wheels, digital readouts for adjustments. -- Contour Unit - CT U-L: Multiuse, Top & Bottom linear and vertical corner trimming; total motors: (4) 2 x 180 W and 2 x 400 W; 12,000 RPM. -- Profile Scraper Unit - 08.519: Profile Scrapers for up to 3 mm thick PVC banding, vertical & horizontal tracing shoes. -- Glue Scraping Unit - 08.521: Flat, Top & Bottom self-tracing Glue Scraper. -- Buffing Unit - 08.617-2: Top & Bottom 0.18 kW x 4 (0.25 HP x 4) - 1,400 RPM. -- Edge Smoothing Unit: Top & Bottom for 1, 2 & 3 mm edge.Control System ICOS OPEN TS: Large color LCD display; displays stored data, on/off workstation sequence, troubleshooting diagnostic; data input by touchscreen, alphanumeric keyboard, and mouse. Microprocessor adjusts according to stored programs or input; pressure section position & pressure control, vertical positioning of all hold-down beam mounted workstations.Complete with:Heavy-Duty "sliding" feed chain with: 70 mm Wide x 60 mm long rubber pad inserts; central lubrication of transport chain; variable feed speed from 4 - 20 MPM (13 - 65 FPM). -- Motorized central height adjustment of top pressure beam with double V-belt hold-down. -- Sound Enclosure - All stations; all trimming & milling motors DC electrical motor brakes for immediate stopping. -- Spraying Units: Upfront at infeed for anti-stick solvent and polishing solvent prior to Buffing Station. -- Actual Model is IMA ADVANTAGE 500 L

IMA - HKA CONTOUR EDGEBANDER: Specifications: -- Manually operated Contour Edgebander. -- Designed for straight or curved (contour) edgebanding with: 0.5 - 3 mm Edgebanding thickness, 16 - 45 mm panel & banding height, 23 - 45 mm min. strip width; 100 mm min. panel width; 250 mm min. strip length. -- Equipped with: Versatile glue head can be fixed to 1-side of the table allows operator to manually manipulate smaller pieces.During "fixed" mounted operation, coil material is drawn in automatically to infeed section of machine. -- Work Table:32" (800 mm) Dia. coil dispensing table, large worktable surface (approx. 36" x 36"); Pre-selection counter for edgebanding material; (1) preheating unit with 600 Watts for preheating of PVC/ABS edges -- Operating Process:Floating edgebanding head is clamped to panel to be processed, precut strip of edgebanding material is fed into glue head,Operator guides head around workpiece, glue is directly applied to precut strip of edgebanding material up to end of strip. -- Features: "Floating head/glue pot" unit (hot melt) with 0.5 Liter cap; Guillotine knife for PVC material (within floating head). -- Complete with: &#9679 (1) 6 m³/Hr cap. vacuum pump for high-flow work table; &#9679 Jib Crane & hoist to support the edgebanding head; &#9679 Thermo-control for glue temperature; &#9679 Foot pedal control to initiate automatic cycle.

IMPERIAL CM-006 Cartridge Modular Pulse Jet Dust/Fume Collector. Designed to be the strongest, safest, and most efficient dust and fume collector in the industry. -- Overall Specs: 4,800 CFM with 2,800 sq. ft. of total filtration media operating at 2.0:1 Air-Cloth-Ratio (ACR). Factory provided compressed air (clean - dried) is supplied to manifold mounted valves providing efficient continuous pulse jet Filter Cleaning System. -- Fan/Motor: MS-180-HD-70-20 Fan driven by 20 HP premium E motor. Efficient backward-inclined fan wheel. Manual slide gate damper on fan discharge. Fan-Silencer at fan outlet. Fan capable of 4,800 CFM at 13" SP. -- Electrical Control Panel: Nema 12 (indoor) enclosure with main breaker houses fan Start, E/stop, continuous On-Demand selector switch, Local/Remote selector. Soft Start drive to reduce power peaks on start up. -- Construction/Housing/Features: Heavy 7 - 10 gage construction with no external bolt holes guaranteeing no leaks for life. Filter access door with lockable handle, heavy duty latches for one handed operation. Tool-free filter change out with 'Even-Lock technology positive stop double sealed ensures cartridges are always installed properly. Filters are fully grounded to dust collector housing. OSHA compliant full length platform and adder access. Bolted support stricture with 54" clearance for 55 Gal drum & adapter.. Discharge via 10" Rhino heavy duty collection drum sealed cover kit requires not airlock with slide gate closure, tool-free sliding coupler, and grounding wire. -- Comes with: High Entry inlet with staggered angle inlet baffle plate provides filter protection and allows material to enter at filter level causing the natural downflow material primary separation effect. Horizontal square to round transition. DWYER DCT1000 control manages the Filter Cleaning System with user-friendly software menu. Solenoid time/on-off/settings and high/low differential pressure control capability Auto/Manual control option. Compressed air pressure regulator and filter. -- Optional: Updated control panel to include a Variable Frequency Drive (VFD) to replace the Soft Start drive and keypad on cabinet door. Upgrade Controls to Include VFD. VFD reduces inrush current at startup saving energy. Also regulates system airflow by maintaining static pressure at the collector inlet. This reduces the load on the motor saving operating cost, instead of dampening the airflow with an outlet damper that is required on other starter options. On system shut down the VFD slows the fan down to a preset speed of 20 HZ for 5 minutes (the duration of the down time cleaning cycle), this prevents dust from backflowing out of the collector due to the cleaning system pressurizing the collector creating a back flow through the ductwork. Please inquire for price.

IMPERIAL - CM-002: CMaxx™ Dust Collector The CMAXX™ was designed with revolutionary cleaning technology that insures maximum pulse cleaning power. The CMAXX™ housing is the largest in the industry with the lowest internal velocities. This large housing causes more dust to drop into the hopper before attaching to the filters. The low internal velocity combined with DeltaMAXX™ filters makes this the most efficient dust collector in the industry.Specifications -- 700 Sq./ft. Filter Media; 2.55 - 1 Air to Media Ratio. -- Main Handle Operator. -- Overload protection. -- NEMA 4 Enclosure. -- Push button start. -- Emergency stop button -- Run indicator lightIncludes -- 7.5 HP Fan Motor Starter with: 1,790 CFM. -- Integrated DWYER - DCT1000 Control. -- Window kit for easy access to Dust Collector settings.

INDUSTRIAL IWS 10 Finger Jointer:Shaper unit will handle material 2" to 8" wide, 5/8" to 2" thick and 5" minimum length and 30" maximum length.Equipped with: -- ( 2) Trim saws with 5 HP motors, (2) Scoring saws with 3 HP motors and (2) Shaper spindles with 15 HP motors - 1-13/16" dia.. -- Feed speeds from 0 to 150 FPM. Average speed of (100) lugs per minute; feed chain is equipped with lugs on 9" spacing. -- Glue applicator with improved glue spreading and simplified pump. -- Model 3502 90° brush transfer to the assembly and Flying Cut Off Saw. -- MOD - Assembly Press, 16' long, with (1) retrim saw, air over hydraulic clamp & squeezing including Complete with: -- Wertern/Nielson 800 FJ cutterhead grinder -- Set up stand -- (15) cutterhead -- Some spare parts