DENRAY 9600 Down Draft Sanding Table: Extra long 48" x 96" table with a 36" working height. -- Rated at 4,300 CFM with 3 HP motor. -- This model features the Tube Filtration System which cleans with a 99% capture rate at 1 micron. -- Includes: (4) Swivel casters, including (2) that lock in place. -- No duct work, no loss of conditioned air. -- Comfortable 1-1/8" thick hardwood frame worktable with 3/4" thick MDF board and rubberized surface.

DENRAY - 3672: Downdraft Sanding TableSpecifications -- Table size: 36" x 72" with: 1-1/8" Tabletop; Working height: 36". -- Rated capacity: 3,500 CFM; Capture rating: 99% at 1 micron; Sound level: 78 dBA.Equipped with: -- (20) Tube filters; 2 HP Motor. -- (2) Locking & (2) fixed swivel casters. -- (3) Receptacles.

DENRAY - 9600 B: Down Draft Sanding TableExtra-large 48" x 96" table; comfortable 29" working height. -- Powerful system with: 4,800 CFM rating. -- 5 HP Motor with: Magnetic starter. -- Space-saving self-contained unit w/built-in dust drawers and high efficiency cartridge filters. -- No ductwork; no loss of conditioned air. -- 1-1/8" Thick hardwood frame worktable with: 3/4" Thick MDF board and rubberized surface. -- Fully Enclosed Unit. -- "Self-Cleaning" System with push-button start to force compressed air from a storage tank into the filters and force dust into the dust drawer. -- Floor level air exhaust that can be directed away from Operator. -- Quiet operation with only 82 dB. -- Includes (4) Swivel casters with: (2) That lock in place; Automatic self-cleaning timer or muffler.

DAC-1200 - DENSACAN: Can DensifierThe "DAC-1200" is fully automatic and will run continuously as long as cans are fed.Features -- Automatic shut off when empty. -- Capacity in pounds/hour. &#9679 Aluminum: 1,200 Lbs. &#9679 Aluminum: Flat 2,000 Lbs; Ferrous: 2,500 Lbs. -- Biscuit description; typical size: 11" x 13" x 9". -- Motor: 20 HP.

DEPENDABLE - 203, ...Cold Press40" x 102" Cap., side loading on 102" sideSpecifications: &#9679 (3) Split upper platens: 34" wide x 40" deep; split platens can be interlocked for single platen operation. &#9679 45" Max. daylight opening with 12" down stroke hydraulic cylinders. &#9679 (6) Rows of pop-up rollers in machine bed for loading & unloading. &#9679 (3) 7-3/4" Dia. hydraulic press cylinders from the top; (1) per platen. &#9679 Hydraulic power pack with 10 HP motor mounted on floor at end of Press.

EXTREMA XP-615AZ Single Sided Head PlanerSpecifications: -- Width: 24" -- Main HP: 15 HP -- Feed HP: 1 HP -- Elevation HP: 0.5 HP -- Max. Thickness: 8.75" -- Min. Thickness: 0.375" -- Max. Cut: 0.25" -- Min. Length: 10.5" -- Cutterhead Speed: 6000 RPM -- Feed Speed: 20-42 ft/min -- Air Requirements: 1000 CFM -- Thickness Adjustment: PLC ControllerBed Roller Adjustment: External -- Powered Bed Rollers: Top and Bottom -- lnfeed Roller: Standard -- Amps (230V / 460V): 41A/20A -- Weight: 2345 LbsFeatures: -- Solid cast-iron construction -- Sectional infeed rollers -- Huge 8-3/4"thickness capacity -- 6000 RPM cutterheads -- Anti-kickback fingers -- Segmented chip breakers -- Sectional feed rollers -- XP-615 Digital Controller -- Motorized table elevation -- Available with straight, STEALTH, or ilECTDFi cutterheads -- Heavy duty screwjack elevation system -- Easy access internal workings -- External bed roller adjustmentsOptional: -- In-feed Roller

EXTREMA - XP-126A: Planer with Helical Head26" x 11-3/4" Cap.; 5/16" max. material removal; 10-1/2" min. part length; 20 HP WESTINGHOUSE / TIKO belt driven motor; STEALTH helical carbide insert cutterhead: 6,000 RPM; variable speed feed: 20 - 75 FPM. -- Equipped with: Powered raise-and-lower of 27" x 35-1/2" table; digital thickness controller; sectional chipbreakers; sectional infeed roller & dual outfeed rollers; (2) adjustable bed rollers.

EXTREMA PERFORMA XS-2P52 Wide Belt Sander (2) Heads;52" Width cap. Drum, Roller and Platen - 75"; Belt Lengths Head Configuration: -- 1st Head: Contact drum 30 HP motor; -- 2nd Head: Roller and Platen 30 HP motor.Features: -- Over thickness safety device -- Infeed bed rollers -- Digital thickness controller -- Individual amp meters -- Disc brakes on sanding heads -- Telemecanique electrics. -- Camozzi pneumatics -- Variable speed drive system.Specification: -- Feed motor 3 HP -- Elevation motor 0.5 HP -- Max. thickness 6" - Min. thickness 1/8" -- Contact drum 1st head 8" dia. -- Roller drum on 2nd head 5" dia. -- Dust Collection requirements 4800 CFM -- Feed speeds 15 - 50 FPM. -- Weight 6500 Lbs -- AMPS (220 V / 460 V ) 148/74.

Extrema WS-110 Single Spindle Shaper -- 3/4" & 1" Interchangeable spindles. -- 3 HP Single Phase, 3,450 RPM motor designed for operation in most smaller shops -- Belt drive for spindle speeds of 8,000 & 10,000 RPM _ 2-5/8" capacity under the nut (3/4" spindle) and 3-7/8" vertical spindle travel will accommodate a variety of cutters. -- Large Table size 28" x 30" with a 6" max. dia. table opening -- Includes Fence assembly, miter gauge, 1/2" collet adapter, and power feeder.

EXTREMA DCY-1425 L3 TYPHOON Cyclone Filtration Dust Collection System. -- Powerful two-stage dust collection drops out heavier dust particles through a Rotary Air Lock, allowing you to choose the disposal system, before passing finer particles through the fan and filter. Free air volume rated @ 10,500 CFM. Low noise operation. -- Equipped with: 25 HP Motor, with a Soft Start already wired in. -- Rotary air lock with a 1 HP motor @ 38 CFM. -- Standard support frame LEG 3 164" clear height x 149" clear width x 91" clear depth. -- (2) DCF-327E exterior Baghouses for more than enough filtering capacity.

EZ CAR - (Used) Model A: Car Crusher Approx: 6,200 hours.New in: 1988.System Pressure: 2,500 PSI.Port Reliefs set at: 2,650 PSI.Cylinders: 10" Bore.Travel: 78".Shaft: 4" rod.OpeningSize: 20" x 8'-1" x 7'-7".OverallWeight: 61,000 Lbs.Length: 43'-1/4."Travel & operating height: 13'-1/4'.

EZ SANDER EZ-3760 Wide Belt SanderEZ-Sander's are built to with the ability to hold very tight tolerance (+/-.003) side to side when set up properly.Specifications: -- The sanding head is a combination head that consists of a 5" rubber-covered contact drum for the more aggressive sanding and then followed by an adjustable 2-1/2" graphite-covered felt polishing platen for doing very fine finishing sanding using a 37" X 60" abrasive belt. -- The conveyor belt speed is set to run at 10 - 30 FPM and is controlled via AC variable speed unit mounted in the main control panel. Simply adjust the dial setting to your desired feed speed. -- Double infeed and outfeed hold-down rolls are provided to help ensure proper part feeding through the Sander. -- The conveyor table/bed opening has a 0" to 5" opening allowing the operator to sand some parts as thick as 5" and the ability to sand very thin parts as well. -- Power raising and lowering of the conveyor bed is standard. -- Digital thickness display is standard.Complete with & Features: -- EZ Sander is equipped with a state-of-the-art electronic tracking system for the abrasive belt. -- Emergency stop heavy-duty caliper disc brakes bring the sanding head to a stop within 4 to 5 Sec when activated by the machine's safety interlock system. -- Limit Switches on both sides of the abrasive belt to keep the belt from over-travel. NOTE: -- Available in single phase with a 7.5 HP or 10 HP 3-Phase main drive motor. -- Voltage change to 440 Volt ...$275.

Cabinet Door Finishing System --4 Air Spray Guns --3 different lines and pumps --Paper feed belt with various speed options --Infrared sensors detect exact measurements of cabinet doors or mouldings and spray only the pieces being sent through. --System includes: (1) Dry Room and fan for air movement. --System is in great condition and works well. Our shop got to the point where we were really only using it to prime doors and it is capable of so much more than that.

FARR GOLD GS4 DUST/FUME/MATERIAL COLLECTOR: 3,000 CFM Rated cap., 1,300 sq. ft. filter area from (4) cartridge filters, approx. 2.3:1 air: cloth ratio . -- Equipped with: 5 HP Pull thru motor; dirty air is pulled into the filter area at bottom of filter media section allowing gross dust particles to fall into collector barrels located beneath pyramidal hopper discharging to a sealed drum (not included) -- Fine dust is pulled up thru the cartridge filters; dust filter cartridges are cleaned by automatic pulse jet with minimum compressed air consumption; cleaned air continues thru blower and is returned to the building air supply thru a silencer.. -- Includes: Cyclone with slide gate discharging into a sealed barrel (not included), electrical control panel, support stand with clearance under hopper, discharge for a waste bin,. access door, some pipe as pictured.

Large table size, extendable in all three directions by up to 39" (1,000 mm) without the requirement of tools. Comfortable one-handed lever operationHeavy-duty eccentric clamp, usable on the left and right-hand side.Specifications: -- 3 HP motor, tilting head, manual hand lever control for mortise length and depth; 13" x 22" table with eccentric clamp -- 3000 RPM, reversible motor that caters for left and right cutting bits and a solid quad-jaw chuck with clamping range from 0–20 mm -- Lateral range of motion is 250 mm, cut depth is 160 mm, available height adjustment is 130 mm and there are solid locking stops in all three directions for setting precise stops.Features: 2-Jaw chuck with 5/8" capacity, Dust control collection tray below the cutter out to an 80 mm outlet,Complete with (2) adjustable and removable extension wings; fence for 90° & 45° mortises, extended stop bar on each side of table.

FELDER FORMAT4 - Profit H08: Flat Table Machine Specifications -- 4’ x 8‘ Flat Table Working Capacity: X: 2,500 mm (98.4";); Y: 1,250 mm (49.2";); Z: 85 mm (3.3";).Gantry Outrigger: (2) synchronized Servo drivers in the X-direction; max. speed rate: 25 MPM (985 IPM). -- (1) Servo Driver: Y-Direction; max. 25 MPM (985 IPM); (1) Servo driver: Z-Direction max.; 15 MPM (590 IPM); power transmission in X. -- Y Via rack & pinion ball bearing spindle on: Z Axis; axis runs on ground linear guides. -- Automatic Centralized Lubrication of all axes -- Nesting Table: (2) Stops in X-direction: (1) Stop in Y-direction, left rear side; (6) manual switches situated in front of the machine; heavy valve system. -- Phenolic Vacuum Table with: (6) Vacuum fields and manual field choice. -- Stop cylinder at: Rear left; (2) in X, (1) in Y direction; electric box front left with light barrier. -- 1 ST 305-01004. -- Configuration package "Professional" H08 13.25 10 kW (S6) main spindle: HSK F63 Left/right rotation; 1,000 - 24,000 RPM controlled by inverter. -- Drilling Head "DH8": (8) Vertical drills; 1,000 - 6,000 RPM; controlled by inverter; 8-position tool changer. Extraction Hood: (22) Separate connections -- Software: Compact; standard PC with Windows 7 Controller; control for the use of ISO-Code; WOODFLASH programs on the machine.Includes: 210 cbm/Hr BECKER Vacuum Pump.

FELDER FORMAT4 PROFIT H08 FLAT TABLE MACHINE (W/LOADING, UNLOADING): -- Specifications5' x 10' "MATRIX" Phenolic Flat Table design for: "Nested Base" Manufacturing. -- Working Capacity"X" Axis is 121.6" (3,090 mm); "Y" axis is 60.2" (1,530 mm);"Z" axis stroke is 11.8" (300 mm); max. material thickness is 4.3" (110 mm). -- Positioning Speed"X" & "Y" Axis at 197 FPM (60 MPM); "Z" axis is 49 FPM (15 MPM). -- WorktableThe working area is subdivided into (8) vacuum fields (H08 16.31) to ensure the best holding force for the most varied board sizes.The vacuum fields are controlled manually by means of: Hand levers on the front side of the machine. Prepared for (optional) elevated pods: Allows profile & horizontal machining. -- Boring Unit(1) DH 8-Spindle Vertical Drill block on 32 mm centers. -- Machining(1) 13.4 HP (10 kW) Vertically mounted electrospindle Router with: HSK F63 Adaptor; inverter driven 1,000 - 24,000 RPM; max. torque from 12,000 RPM.(1) 15-Position ATC Tool Rack: Mounted at the end of the machine. -- Operator & Machine ControlPC Based user-friendly; icon driven control housed on the: Main machine base + "WOODFLASH" Operating System. -- Complete with:(2) 250 cbm/Hr Vacuum pumps; handheld terminal with: Potentiometer & emergency stop; automatic measuring system of the tool length.Sound absorbing protective head enclosure with: Debris curtain around bottom edge. -- Options Include: Automatic unloading unit with: Electromotive offloading pusher. This addition allows finished workpieces to be automatically pushed off the table after processing: Reducing manual handling & speeding up production cycles. -- Actual model: FELDER FORMAT4 - PROFIT H08 16.31

FELDER - G-330: Edgebander0.4 - 3 mm Edge thickness cap.; 40 mm panel thickness; 3" min. width; 4-3/4" min. panel length.Equipped with: -- Quickmelt TEFLON coated glue pot for granular hot-melt adhesive. -- Heavy-Duty Guillotine: Up to 3 mm thick PVC. -- Integrated Operator PLC controls and an LCD display. -- "Anti-slip" rubberized surface chain pads.Workstations -- Single motor; Double Blade End Trim with: HF Motor; 12,000 RPM. -- Top & Bottom Flush/Bevel Trim: Bevels 0° - 15°; 1/2 HP motor - 12,000 RPM each. -- Open space at outfeed. -- Single feed speed: 26 FPM.Complete with: -- Sound & Safety enclosure over trim stations; outrigger panel support; used tooling.NOTE: Seller states that the equipment has less than (500) hours of use!

FELDER RL-350 Dust CollectorFelder clean-air extractors filter the air so that the dust remaining is less than 0.1mg/m cu. These exceptional air quality values are achieved by the position of the impeller. In other extracting systems, the impeller works by creating pressure between the machine and filter; with the Felder systems, the impeller is located on the clean-air side creating negative pressure throughout the system so no dust can escape. Specifications: -- 15 HP blower with 13-3/4" in-let -- Max. airflow 4,705 CFM, nominal air flow capacity 4,072 CFM -- Static pressure 9.4" WG -- Compressed air connection for automatic cleaning function. -- Dust emission quality less than mg/m cu. -- Filter surface area 71 m/sq. -- Acoustic pressure 75 dB -- Chip volume 2 x 55 gal. -- Dimension / Weight: 104" L x 45" W x 89" H, 1,785 lbs.

FELDER - FORMAT KAPPA 450: Sliding Table SawSpecifications -- 126" (3,200 mm) Cutting length w/scoring; anodized 14-3/4" x 126" aluminum sliding table with tracking by roller bearings; locks for easy panel loading in any position; 450 mm dia. main saw blade. -- Motorized: Raise, lower, and tilting (0° - 45°) of the blade with digital readout. Equipped with: -- 7-1/2 HP Main motor; 1.0 HP scoring motor unit w/external adjustment; square crosscut fence with: (2) Stops; standard rip fence with: 1,250 mm (49") Rip cap. w/digital readout; extension table with: Miter fence and sliding outrigger support. Includes: -- (2) 4" Dia. dust outlets; swing away overarm saw guard.Also available for an extra fee: 30 KVA; 208 - 380 Volt 3-Phase Transformer.