HURST 205 HP / 6.9mm BTU / 15 PSIG WET WOODY BIOMASS FIRED BOILER/STEAM PLANT: -- Specifications: Complete in-place system with the following features: -- 205 HP Biomass Wood Fired Boiler, 7,073 PPH, gross steam output @ 212° F. -- Low Pressure "Fire Tube" design fire box model FB-1332-15-UF, built in accordance with ASME Code. -- Operator Interface:Allen Bradley PLC with Power Supply Rack. Pentium-based computer with network & modem remote communication capabilities with operator interface software. -- RSView Runtime for automatic operating of the steam pressure, temperatures, fuel flow & combustion airflow. -- The control system incorporates a 4-20 milliamp steam pressure transmitter to sense any changes in steam flow, boiler pressure, & regulates the fuel feed & combustion airflow accordingly. -- Complete with:Additional details on file for the scope of this Complete System's original project.NOTE: Building that houses Boiler can be included with Boiler if desired by Buyer.

HURST SERIES 45 BOILER, NATURAL GAS: -- SpecificationsBuilt New in 2016; Complete, never installed & ready to deliver! 207.5 HP; 60 PSI Hot Water; Natural Gas Fired Firebox -- Efficient 3-pass design NATURAL GAS FIREBOX. -- ASME Code constructed & stamped for 15 PSI Stream: 30 - 100 PSI Water. -- Registered with the National Board of Boiler Inspectors. -- Easily maintained, designed for efficiency; large Furnace volume for ultimate combustion efficiency -- Unified refractory base floor; steel skids; lifting eyes. -- Low heat release; Factory insulated. – 2"; Mineral wool, Factory jacketed & painted. -- Easy access to fireside surfaces; ample waterside clean-out openings -- Fully automatic operation; U.L. listed; forced draft Burners. -- Wet back construction. -- U.L. Listed controls & trim. -- Factory test fired, flame observation ports front & rear.Boiler Design. 3-Pass “FireBox"; design with: Stress relieving “Wetback"; fire tube construction.Hot Water pressures models are from: 8.5 - 415 HP; 100 PSI max.; 500 - 813 HP; 60 PSI max. built to Section-IV ASME Code.Hot water temperature not to exceed 250° degrees F at or near the outlet of Boiler.Hot Water Model Trim. Safety relief valve; operating temperature control; high limit temperature control with manual reset; combination pressure & temperature gauge; low water cutoff control with manual reset.Hot Water Supply. 180 D/F Return: 160 D/F. -- Fireside Heating Surface: 830 Sq/ft. Furnace volume: 132 Cu/ft. Hot water outlet: 8"; hot water drain: 6"; drain connection: 2".Burner: Matched UL listed “forced draft"; power burners with factory pre-piped, wired and tested fuel configurations for natural gas, propane (LP) gas, No. 2 (diesel) oil, or combination of both gas/oil.All units are factory packaged with operating controls, relief valves, burner, and fuel train. Installation is made simple in that only service connections are needed to place in operation.High density 2"; mineral wool insulation assures lower radiant heat loss. In addition to meeting the requirements of U.L., Burner Systems are optionally available to meet the requirements of FM, IRI, Military, and others. -- Actual model is: HURST S45 – G – 207.5 – 60W

HUSTLER - FC-2, ...ScreenSpecifications: -- OD at the longest point: 104" -- Long at longest point: 122" -- Tall at the tallest point: 65"Equipped with: -- (2) Shutoff switches

(1) SET OF JACKSON SHAVING MILLS;COMPRISED OF: -- (1) Jackson Model 30D6 Shaving Mill -- (1) Jackson Model 30D10 Shaving Mill -- Chain Drive 4-1/2 Feet Boxes -- (1) Custom Built 2- Head shaver -- Shaving Discharge Belt Conveyor Under Each Shavers. -- Log Deck -- Log trough conveyor. -- Screen -- Loaded on Truck or Container.

JOHNSON LOOSE BAGGING SYSTEMOne Set of (2) Loose Fill Bagging Systems -- Was Bagging Wood Chips in Plastic Bags. -- One Hopper receiving System for the (2) Units -- Two feeding systems -- Complete with Support Legs and Bag Conveyor -- Output Finish Bag Conveyors -- One Unit is Brand New and the Other is in Very Good Working Condition -- Production Rate 6 to 10 Bags Per Minute. -- Could Bag any Type of Free Flowing Material.Price is Loaded on your Truck.

50 HP JORDAN - MS4220: Dual Shaft Shredder with Infeed ConveyorSpecifications -- Overall length: 141". -- Overall width: 56". -- Overall height: 98". -- Cutting chamber size: 42" x 20". -- Hopper size: 1-1/2 - 2 Cubic yard. -- Cutter assembly height: 13-1/2". -- Motor horsepower: 50 HP. -- Approx chamber weight: 4,570 Lbs. MS-4220 is a most popular midrange Shredder with: Power to handle tougher jobs; cost that can fit into your demanding budget. MS-4220 can be used to Shred: Paper, plastic, passenger tires, carpet, and an many other materials. Shredder is designed with: Counterrotating dual speed shafts; cutting group continuously changes knife tip position. This helps the knives grab & pull through hard to hold materials. MS-4220 Industrial Shredder offers: Midsize chamber capacity; horsepower to handle many of the most demanding applications. For a cost-effective Shredder, this unit cannot be beat for volume reduction & material shredding. The MS-4220 Industrial Shredder is a "Workhorse."

KAWASAKI FS030L E Palletizing RobotArticulating arm type Palletizing Robot.Specifications: -- Suction cup type "pickup". -- PENDANT 6 AXIS -- Controller Model "D32FD001" -- Capacity: 30 kG (66 Lbs) bags. -- Complete with pendant control station. -- Includes control panel Cabinet. -- Dimension; 98" H x 42" W x 98" L (wooden crate); weight approx. 3,190 Lbs.Loaded on your truckNOTE: (2) Units available!

KAY INDUSTRIES Phasemaster MA-1 5 HP Rotary Phase Converter.Features: 5 HP Largest single motor starting capacity; will run 10 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-1 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-1-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 522Optional LSV option for sensitive electronics add...$ 550

KAY INDUSTRIES Phasemaster MA-2, 10 HP Rotary Phase Converter.Features: 10 HP Largest single motor starting capacity; will run 20 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-2 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-2-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 500Optional LSV option for sensitive electronics add...$ 900

KAY INDUSTRIES Phasemaster MA-6, 30 HP Rotary Phase Converter.Features: 30 HP Largest single motor starting capacity; will run 60 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-6 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-6-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 7006Optional LSV option for sensitive electronics add...$ 1,200

KAY INDUSTRIES Phasemaster MA-8, 50 HP Rotary Phase Converter.Features: -- 50 HP Largest single motor starting capacity; will run 100 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-8 provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: -- 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-8-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 1,500Optional LSV option for sensitive electronics add...$ 3,600

KAY INDUSTRIES Phasemaster MA-1B, 7.5 HP Rotary Phase Converter.Features: 7.5 HP Largest single motor starting capacity; will run 15 HP total 3-phase machines from 1-phase input voltage. -- 208/230/460 Single-phase input voltage configuration available (please specify upon order). -- Less than 1% harmonic content, greater than 95% Power Factor & Operating Efficiency at full load; Heavy Duty General Purpose Design will operate any woodworking machinery; quiet running (1,800 RPM); produces true three-phase Delta output ideal for CNC equipment. -- The Phasemaster MA-1B provides instant motor reversing; buffered soft-start for three-phase loads which potentially reduce electrical operating costs; allows loads to develop full nameplate power ratings. -- Includes: 5-Year warranty. -- Does not include fuses or switch.Phasemaster MA-1B-R includes factory-installed disconnect switch, fuses and terminal blocks in a side-mounted electrical enclosure for additional;...$ 500Optional LSV option for sensitive electronics add...$ 900

KCB BAGS BIG SACKS BULK TOTES "NEW"Bulk Bags, never used. -- Bag size: 35" x 35" x 25" S/S. -- 2,200 Lbs, SWL (1,000 kg), Safety factor 5:1. -- Document pouch. -- Fill spout top inlet. -- Bottom discharge chute with flap, liner. -- Min. purchase quantity is 500 bags. -- Special Price for Higher Quantities -- Loaded on your truck

KEESTRACK - Frontier: Portable ScreenerTechnical Specifications -- Capacity: Up to 600 ton. -- Weight: 30 Ton. -- Screen box (L x W): 4,500 x 1,800 mm. -- Feed hopper in HB450: 8 cbm. -- Hydraulic folding hopper for transport.• Heavy-Duty Plate Apron Feeder: 3,560 x 1,300 mm. -- Loading height. Open back wall: 2,420 mm; half open back wall: 2,850 mm; closed back wall: 3,260 mm. -- Side loading length: 4,400 mm Screen box L x 4,500 W x 1,800 mm Hydraulic liftable screen box.• Screen box can be set in several inclination: Standard walkway beside screen box; Standard Long Life. -- Grease: Interval every (250) Hrs. -- The 1st (2,500) Hrs of its life was used to screen mulch. The rest was used to screen concrete. Needs a starter, but we just wired a direct push button to it. Great shape: Has some surface rust but just cosmetic.New main belt & fines belt in the last (100) Hrs.

KOHLER - 20REOZJB, ...Diesel GeneratorSpecifications: Rated at 23 - 30 KVA when used as primary; 25-34 KVA as standby.90 - 600 V, 3-Phase, 60 Hz. -- Brushless; rotating field Generator has broad range capability(176) Total operating hours running time.

KOHLER - KG 100, ...Natural Gas GeneratorNatural gas-powered Generator. -- Rated at 125 KVA. -- Primary Voltage: 247/600 V - 3-phase, 60 Hz, 121 Amps. -- 100 kW, 150.5 Amps. -- 1,800 RPM - 12 Volt battery.

MARCUS TRANSFORMER 15 KVA, 3-Ph, Auto, 600/480 V Transformer with tap for 440 V.15 KVA Auto-ventilated "dry type" transformer 600 V in (primary); 480 V out (secondary) with tap on secondary for 440V at full capacity. -- Manufactured with grain oriented silicon steel is used. -- Coil windings with high quality magnet wire and the enclosure is made of heavy gauge steel w/ventilation openings. -- UL and CSA approved.

MATH-EX Bag FlattenerSpecifications: -- Standard Bag Flattener conveyors are 10' in length with a 15° incline. -- The system has an opposed 5-1/2 foot conveyor with parallel linkage and adjustable spacing for various bag thicknesses. -- The standard unit has a 12" inlet and 42" discharge. -- The lower conveyor has a 1-1/2 HP motor and the top conveyor has a 1 HP motor both with a speed of 90 FPM. -- Both conveyors come with 24" wide Roughtop black belt.Custom length bag flatteners are available in 2' increments from 10 feet to 24'. Mild steel construction with industrial powder coat finish is standard, however all stainless steel, corrosive resistance packages and hazardous location components are available as option.

MATH-EX BAG TURNER WITH CONVEYORSpecifications: -- Bag Turner/Knockdown Conveyor -- 5' Long x 24" Wide Smooth Top Belting -- Includes Turn Wheel -- 30" Stainless Steel Turn Plate and Adjustable Knockdown Bar -- 1/2 HP Motor at 90 FPMLoaded on your truck

MATH-EX - SUCTION CUP END TOOLING ARM FOR FANUC ROBOT -- Suction Type Pick Up Tooling Arm. -- Specially Designed for FANUC Robot. -- To Palletize Pillow Type Bag up to 75 Lbs. -- This Tooling will be Installed on a FANUC Robot. -- Loaded onto your truck.