Planers For Sale

Newman 382 Helical Head Double Surface Planer with Hydraulic Power Unit

MLS Number 10908375 Newman S-282 Wood Planer Used 18 x 16 S-282 Newman Serial number 14467 Helical 6 knives Length 18” Top head 40 Hp Bottom head 25 Hp 15 Hp HPU Voltage 460

Newman S-382-HD Double Head Planer with Helical Heads & Hydraulic Power Unit

Newman 282 Wood Planer 18 inch wide planning capacity by 6 inch thickness Newman 6 row Quite-cut carbide cutterhead 50 to 75 percent carbide knife life remaining 40 HP 3600 rpm top head motor-DMD 25 HP 3600 rpm bottom head motor- DMD 15 HP hydraulic pump package Feed speeds : 40 to 150 feet per minute Rubber tire feed – one row in-feed and one row out-feed. Dust hood Carbide knife grinder and jointer Cleaned and tested

Newman S282 Planer

Newman M512 Planer Matcher - 4 Main Heads - Added 2 heads - Machine was working and in use when removed from service. Seller purchased used and never installed. - Machine was running 6x8 D logs for a cabin manufacturer - Infeed rollers

Newman Planer Pineapple Infeed

Newman S-382-HD Straight Knife Planer with Hydraulics & Controls S/N 14267

Newman S-382 with Helical Quiet Cut Planer Heads & Hydraulics to Run it. (not pictured)

Newman S-382 Double Head Planer (Straight Knives) w/Hydraulics & Controls S/N 15292

Newman 4 Sided Planer

Newman S970 Planer 30" x 10" capacity 50 HP top/Bottom motors 5 hp feed motor straight knives with grinder

Newman S-382-HD Planer S/N 14069 - 7379 Hrs - 40HP Top Arbor & 75HP Bottom Arbor Includes Hydraulic Power Unit.

NORTHTECH NT 1000-50HCVS Single-Sided 40" PlanerSpecifications: -- 40" Planer, 40 HP main motor, Helical Head, Adjustable bed rollers 15 mm x 15 mm x 2.5 mm Carbide Insert cutters. -- The spiral cutterhead provides a high chip removal rate, superior surface finish and low noise. -- Powerful 40 HP cutterhead motor makes this planer ideal for heavy-duty planing and meets high production requirements. -- Variable feed speed is mechanical variable from 0 - 90 FPM. -- Power elevation of the feed bed with "727 M Digital Table Adjustment" for fast accurate, and convenient thickness setting. -- Extra heavy rib reinforced cast iron table, surface precision ground. Equipped with: -- (4) Powered steel bed rollers. -- (4) Upper rollers. -- (2) Powered corrugated infeed rollers. -- (2) Powered urethane outfeed rollers. -- Upper and lower limit switches for opening control. -- (4) Dual 50 mm jack screws for raise/lower bed movement; 12" max opening. -- 2 HP Elevation motor with manual adjust. -- Rear E-Stop for added safety. -- Dual 6" dust ports requiring 1,000 CFM @ points of extraction.

NORTHTECH NT-610EL Top & Bottom Planer:24" Wide x 7.5" thick capacity; 1/4" minimum thickness; 12" minimum stock length.Specifications: -- Cutterheads: 25 HP top head; 20 HP bottom head; 5,800 RPM on cutterheads; (6) row spiral insert cutterheads, Carbide knives 15 mm x 15 mm x 2.5 mm 4-sided -- Feed works: 3 HP variable speed feed with speeds from 20 to 75 FPM; 1 HP motorized raise and lower of bed; DP-525 digital thickness controller; Overhead carpet style feed system Equipped with & Features -- Sectional chip breaker; Hard chrome plated bed; Automatic lubrication for feed system; Amp load meter -- Dust Requirements: 3,800 CFM; (1)10" and (1) 7" dust outlet Seller states this machine has less than 600 Hours of use.

OLIVER 4470 25" Shelix Cutterhead Planer; 10 HP motor Single Phase, or 15 HP 3-Phase motor. Full 25" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through , Byrd Shelix Cutterhead this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor.

OLIVER 299 Single Surface Planer;24" Width x 8" thickness cap., Cabinet Planer; -- 7.5 HP Cutterhead motor, and the OLIVER "ITCH" carbide cutterhead. -- 2 HP Gear box variable speed feed works with speeds of 15 - 60 FPM; sectional feed rolls, sectional chipbreakers. -- Complete with: Knife grinding equipment for OLIVER carbide cutterhead, knife setting device, top dust hood, quick set adjustment on bed rollers.One of the "Original" OLIVER Planers!

OLIVER 4430 20" PLANER WITH HELICAL HEAD20" Maximum stock width cap., 1/4" to 8" max. stock thickness, 10" minimum stock length. Equipped with: -- 5 HP Main drive motor and mechanical raising and lowering of the cutter head. -- Fixed bed height of 29-7/8". Table dimensions 20"L X 21"W. Overall all table dimensions with infeed and outfeed bed extensions 51"L X 21"W. -- 3-1/4" Dia. Helical Cutter Head with 4-sided carbide inserts. -- Auto-Depth lock via nitrogen-charged cylinders eliminates snipping. -- 8" Max. thickness adjustment via handwheel includes LED Digital readout for head positioning. -- 4-Post support for proper head alignment.Complete with: -- 5" Dust outlet and built-in mobile base for ease of movement

OLIVER 4470 25" Straight Knife Planer Full 24" of cutting width, over 9" of cutting capacity, and the ability to take up to 1/4" off in a single pass through the 4-knife standard cutter head, this planer will take whatever you can dish out. -- The Digital Thickness Controller and Powered Table Travel eliminate guesswork, make dialing in settings a breeze. But ease of operation isn't everything, this OLIVER outputs stock that's true and straight. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on uneven stock, coupled with a Driven Outfeed Roller to keep your stock in place. -- And a powerful 10 HP motor Single Phase motor, or 15 HP 3-Phase motor. --OPTIONAL EQUIPMENT: Byrd Shelix Cutterhead (ADD $2,400)

OLIVER 4455 22" Straight Knife Planer, 5 HP single phase or 10 HP, 3-Ph.The OLIVER "4455" Planer has a super-wide capacity, it'll handle stock up to 22" wide, and takes up to 3/16" off in a single pass.Specifications: -- 4-Knife HSS straight knife cutter head. -- A Sectional Infeed Roller and Chip Breaker apply uniform pressure on an uneven stock, coupled with a Driven Outfeed Roller to keep your stock moving smoothly. -- Add (2) feed speeds for extra quality, a Digital Thickness Guage for quick reference, and a powerful 10 HP motor. -- Max depth of cut 3/16" min part length 10"; Max work pc 22" w x 9" Thickness.