Hogs and Wood Grinders For Sale

Vecoplan Model 45/12/2VU HZF Grinder 75 HP Motor 18" Wide opening No Vibrating Infeed conveyor

VECOPLAN RG 70/200K Shredder with Steel Belt Conveyor & Dust CollectorSpecifications: -- Hopper Opening: 70″ x 80″ -- Hopper Volume: 4 – 6-1/2 Cubic Yards -- Main motor: 200 HP -- Rotor diameter: 20″ -- Number of cutters: 84 (triple row) -- Size of cutters: 40 mm x 60 mm -- Screen size: Holes 2″ -- Rotor speed: 145 RPM -- Rotor diameter: 20″ -- Hydraulic Feed Ram: 10 HP - 2-Speed -- Throughput: 2,000 – 28,000 Lbs/HrEquipped with: -- 10 HP Motor Dust Collector -- 48″ W kW SCHMIDT Shredder Infeed Conveyor w/ 20′ pit section

2019 Vecoplan VHZ1600 | 1300 run hours | Excellent Condition | 2 Available in June of 2025

VECOPLAN RG 42-40 SINGLE SHAFT SHREDDERSpecifications; -- 40 HP MotorVecoplan ShredderModel: RG 42/40 XL PVYear: 2007Motor: 40 HP, 460V, 60HZRPM: 1465Feed Opening: 42" x 48"Blades on rotor: 27Weight: 3,700 lbs

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

VECOPLAN RG52/60 SINGLE SHAFT SHREDDER Includes Box Dumper and ConveyorsSpecifications: --In Feed Opening: 52″ x 58″ --Rotor Length: 52″ --Rotor Diameter: 15″ --Hopper Volume: (4) Cubic Yards --Cutters: 37 --Drive Motor: 60 HP --Box Dumper / Table --Infeed Conveyor --Discharge Conveyor for Gaylord Box Loading

This Grinder was recently taken out of service and was running good. No electrical controls. Ready to load.

This Grinder was recently just taken out of service. It ran very good before taken out. Does not include electrical controls.

Low Noise Grinder with Horizontal Feed; 50 HP Main drive motor, 16" diameter rotor with (24) 40 x 40 cutters; top & bottom knurled infeed rolls control feeding. -- 5" x 18" Infeed opening; 390 RPM rotor speed. -- Includes: (1) 18" Wide x 6" deep x 16' long vibratory horizontal infeed conveyor; sizing screen with 7/16" screen hole. -- Approximately 10,163 hrs on this unit.

2017 Vermeer HG6000 Horizontal Grinder -4,400 hours -C-18 -Belts good -No blowby Turn Key Unit

2013 Vermeer HG6000 -6000 hours -CAT C-18 engine -New material output belt that comes with it -Tires and lights good

Vermeer HG365 Grinder New infeed roll and remote control Ready to go to work!

Manufacturer NV300 - With bilateral linear action providing profiling and straight knife grinding up to a max of 310 mm. Will shape and regrind moulder knives in the block and profile grind solid tipped heads. Suitable for HSS, Stellite and TCT. Max length of cutter profile 310 mm. Max dia of cutting circle 300 mm. Includes arbor, grinding wheel, stylus, 220 volt 3-phase

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

WEIMA ZM-40 Quad Shaft 4-Shaft ShredderEquipped with: -- Dual drive motors - (2) 30 HP Drive motors. -- Hopper opening measures 51" x 55.1" (1,300 x 1,400 mm); cutting chamber opening of 30" x 27.6" (762 x 700 mm). -- Rotor length of 30" (762 mm); Rotor speed 25 RPM; cutting disc 11" (280 mm) diameter. -- Complete with: -- Control Panel with soft start and 16' cable bundle. -- Note: "Quad Shaft" Shredders, unlike Dual Shaft Shredders, allow shredded material to be circulated through the cutting chamber until it is small enough to pass through the sizing screen. -- Machine weight: 5,500 Lbs.

Weima WLB 1300 Horizontal Grinder 50 HP Motor System works, not currently in use, will need main bearing replaced.

WEIMA ZM-30 Quad Shaft 4-Shaft ShredderEquipped with: Model- ZM 30 S -- Unit was used to shred wire (6,000 – 8,000 lbs per hour) --20mm screen included 25 HP x 2 --480V- 3 phase --Cutting chamber is 19"; x 27"; Hopper is 33"; x 48"; --The ZM30S is a beefed up version of the ZM 30. Unit has the same size motors, shafts and cutters as the ZM 50 but with a shorter shaft length

WEIMA WL-6 Low Noise Vertical Hopper Waste Grinder Specifications: -- Low noise hopper-fed grinder with a 10" dia X 31.5" long rotor and a 24HP drive package that includes a 2-sided flared hopper. -- Vertical 1.3 cubic yard hopper with 31.5" x 39.2" (800 mm x 900 mm) opening. Equipped with: -- (21) Recessed concave cutters with low clearance over the rotor to extend cutter life, protect the bolts, and reduce machine wear. -- Rotor operates at 80 - 100 RPM with outputs ranging from 1,000 - 34,000 Lb/Hr depending on screen size and material.Includes: -- Control panel.(4,926) Total operating hours.

WEIMA - WLB 400, ...Horizontal Low Speed Grinder Equipped with: -- 25 HP Rotor motor; rotor with (18) 4-way indexable, replaceable cutter knives. Features: -- Top infeed roller; 15-1/2" x 2-1/2" feed opening; Heavy-Duty Industrial Grade construction with stress relieved shell and frame; Heavy-Duty outboard roller bearings; separate electrical control panel. Complete with: -- 8" Dia. collection outlet;

WEIMA - Woodchuck: Low Noise Slow Speed Vertical Wood Waste GrinderLow cost/investment solution for Woodwaste disposal - feasible for a small shop.Specifications -- 25 HP Main Drive motor; 24" x 41" hopper opening; 0.74 cu. yds cap; 10" dia. rotor, 100 RPM. -- Equipped with: -- (28) 40 mm x 40 mm Concave; indexable cutters; 6" discharge outlet. -- Features -- Patented V-ROTOR design utilizes tooling closely matched to grooves in the counter knife. -- V-ROTOR Produces: Uniform discharged material; free of splinters; dedicates more horsepower to grinding. -- Includes -- 5/8" or 3/4" Screen (TBD); integrated "plug-and-play" electrical control system with: UL Approved components. -- (5,454) Total operating hours.