ROCKWELL/DELTA 16-RAS, 16" Radial Arm SawSpecifications: -- Blade dia. 16";; base size 37" x 37 x 31"; H; approx. 18" crosscut cap.; approx. 42"; out & 26"; rip cap.Equipped with: -- 5 HP - 3,450 RPM Motor; 34-1/2" table height sitting on mobile base; 32-1/2" without. Includes: -- (5) Sharpened blades.

ROCKWELL - 43-340: ShaperHeavy-Duty Shaper;; series 43-340. -- 1 HP. -- Table Size: 27" x 36".

ROSE MACHINERY LCFCMS14 PANEL RIPPER TO MOULDER TRANSFER SYSTEM OUTFEED ROLLCASE: -- Outfeed Rollcase receives material from the LHI Panel Ripper at 47 1/4"; elevation and drops down to place the lumber onto the Transfer Chains at 42"; elevation. 66"; wide rolls are 2-12"; diameter steel rolls, snap in style on 12"; centers. Rolls are powered by a line shaft using round Eagle Belts and a 1-1/2 HP gear-motor. The conveyor will be fabricated from tubular and sheet steel and designed to interface with the Transfer Chains. The conveyor speed is 80-120 FPM to create a gap between courses exiting the Panel Ripper. The drop will be triggered when a photocell detects the leading end of the boards, creating a far side lumber line. A pneumatic cylinder provides lifting power. When the transferred boards clear the rolls, another photocell triggers the rolls to return to the up position. Stock length handled by the Outfeed Rollcase is from 6’ to 16’. Elevation adjustment is +/- 1";.TRANSFER CHAINS: -- Transfer Chains receive material from the Outfeed Rollcase. The Transfer Chains are fabricated from tubular and structural steel. There are (6) strands of 2060H conveyor chain approximately 17’-6"; CC long, leaving 11’ clear space to accumulate (2) layers of ripped strips. (2) sets of pin stops are incorporated to keep the layers separate. The conveyor is powered by a 1-1/2 HP gear motor. Conveyor speed is 90 FPM maximum. Elevation is 42"; +/- 1";. LATERAL CHAIN FEED TABLE (ROSE MODEL LCFCMS14): -- Standard duty low friction flat top steel infeed chains drive the stock to the fence. The fence is adjustable for alignment with downstream equipment such as a Moulder. (3) lower powered feed rolls are smooth steel and non-marking. The feed rolls and chains are controlled by adjustable frequency drives. (3) upper pinch rolls are 5"; diameter urethane. The first (2) rolls singulate pieces while (1) pinch roll keeps the board moving on the bridge. The pinch rolls are triggered by photocells. A PLC in the control cabinet cycles the outputs based on operator input. Operator controls allow for start and stop of the chains and rolls, the feed to be paused, the rolls to be reversed and speed controls. -- Fabricated structural steel frame -- Passline height 42"; +/- 1"; -- Stock width 2"; to 9"; -- Stock Thickness 1/4"; to 4"; -- Stock Length 6’ - 16’ -- Rolls include a variable feed rate from 60 to 300 FPM -- Feed roll drive is by a 3 HP gearmotor -- (6) infeed chains, each 50"; long, are driven by a 1-1/2 HP gearmotor -- Infeed chain's variable feed rate is 20 to 75 FPM -- 2-1/2"; bore air cylinders actuate the pinch rolls -- With 3/4"; fence adjustment. ELECTRICAL CONTROLS: -- Controls are incorporated in the LCF Cabinet for the above Transfer System. It consists of operator controls, (2) VFDs, and additional PLC I/O and programming. STARTUP: -- 2-days startup assistance is included. Travel expenses are billed se

ROSE MACHINERY TRANSFER SYSTEM: PANEL RIPPER TO MOULDER INFEED OUTFEED TRANSFERA Rollcase will carry stock away from a LHI 72" Panel Ripper. When the stock reaches the far end-stop, a 6-Strand Transfer Belt will pop up and take the stock to a Lateral Chain Feeder (supplied by others). The lifting mechanism is triggered by photocells and powered by an air bag using plant air. When the stock clears the Rollcase, the transfer will return to the down position to receive the next batch of strips. Rollcase Specs:17' 0" long; 76" between frame; 1.9" dia. X 12 gauge rollers. Galvanized rollers are set high on 3" centers. 5-1/2" x 1-1/2" x 12 gauge formed steel channel frames; welded construction. 120 FPM maximum. Dual shaft w/jump chain; underhung drive; timing belt driven; 1 HP, 575 volt/3ph/60hz motor; less controls. With (3) H-style leg supports; 34" top of roller; adjustable 32" to 38", with knee braces. Fixed angle end-stop. Frame is powder coated blue; guards powder coated yellow. Transfer Specs:B/17 purple power twist belt; 36" strand centers; 10'-0" long. UHMW chain track; airbag lifting style; thru frame; 36" top of chain. With 1/2 HP Boston 575 volt/3ph/60hz motor with Boston reducer for 120 FPM; less controller; proximity switches to detect carriage position are mounted only; solenoid valve, mounted and plumbed; filter/regulator - mounted and plumbed. With central bearing lube. Frame is powder coated blue; guards powder coated yellow Electrical Controls:ROSE provides an Electrical Control & Cabinet that will control the above Outfeed Transfer System. Electrical Control will incorporate a fused disconnect for incoming power, transformer and power supply for control voltage, (4) variable frequency drives for the motors, a PLC to read input devices and control output devices, and pushbuttons/switches for operator control. The panel will be mounted and wired to the enclosed devices. Incoming power and other field wiring is by others. Two days startup assistance is included. Travel expenses will be billed at cost separately.Conditions:All gear-motors, mechanical equipment, limit switches, sensors or photoelectric devices as required for each item of this quotation, will be supplied and mounted. All pneumatic cylinders or other pneumatic power devices and their valves will be supplied and mounted. They will have connecting hoses and fittings installed. Filter/Regulator units will be supplied, mounted and connected by hose to the valves. Compressed air service to equipment is by others.Exclusions:This proposal describes the machinery to be provided by Rose Machinery Inc.. The equipment supplied by Rose Machinery Inc. is specifically limited to the items actually described in the itemized details of this quotation. Unless specifically mentioned herein, all other items and services are the responsibility of the Buyer. State or local sales taxes, or any permit or other fees that may be required are not included. All field wiring, plumbing, and installat

SNX nVISION SYSTEM2 G2 CONTOUR EDGEBANDER + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming: -- Specifications: Curved (Contour) Edgebander to allow 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The nVision Contour Bander can band a minimum material size of 150 mm (6") diameter.Maximum material size 2,400 x 2,400 mm (94" x 94"); Maximum material weight up to 104.5 KG (230 LBS).Material thickness from 10 - 60 mm (0.4" - 2.36"); Banding thickness from 0.5 mm thin tape w/low temp adhesive - 3mm tape. -- Radii Capacity:Minimum Internal (inside) radius 80 mm (3.14"); minimum external (outside) radius 30 mm (1'18") based on 1 mm thick edge tape. Edgebanding thickness 1 mm, min = R 30 mm Edge thickness 2 mm, min = R 50 mm Edge thickness 3 mm, min = R 80 mm Panel thickness 10-60 mm with edge thickness 1 mm Panel thickness 10-60 mm with edge thickness 2 mm Panel thickness 10-45 mm with edge thickness 3 mmIMPORTANT: ALL minimum & maximum radii are affected by tape thickness, quality of adhesive and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape, semi or rigid. -- Equipped with:(1) Thermal-regulated glue pot heated via (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 KG (2.2 LBS) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2.25"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.The Laser also detects a tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.The machine is also equipped with a foot pedal for manual control/intervention. Motorized turntable for automated edgebanding application on large panels.(2) "Heavy Duty" Articulating arms to support the parts during edgebanding and trimming. Arm has a large interchangeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. Tolerances of inner & outer radii and fit within the work area. -- Complete with: Top & Bottom Trimming unit Centralized control panel with Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired Banding station Edgeband coil stand Standard-size vacuum pod for articulated arm 80 mm dia. (3") dust extraction outlet Foot pedal activation/de-activation control Larger feed roller &#9

SNX nVISION C 1.5 CONTOUR EDGEBANDER: -- Specifications The "nVision C1.5" Curved (Contour) Edgebander allows 360° edgebanding to contoured (shaped) panels. The Standard banding machine includes banding and trimming stations with: (1) Set of cutting tools; (1) articulated vacuum arm; edgeband coil stand; (1) 8″ aluminum vacuum pod. - Includes: On-site installation and training; free phone support; operation manual; 1-year limited warranty.The machine uses: Standard EVA hot melt glue and can apply 0.5 mm - 3 mm thick edgebanding.Edgebanding is applied automatically as the part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation: Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working Capacity: The "nVision C 1.5" can band minimum material size: 150 mm (6") Diameter.Max. material size: 2,400 x 2,400 mm (94" x 94"); max. material weight: up to 104.5 kG (230 Lbs).Material thickness from: 10 - 60 mm (0.4" - 2.36"); Banding thickness from: 0.5 mm thin tape w/low temp. adhesive: 3 mm Tape. -- Radii CapacityMin. internal (inside) radius: 11.1 mm (0.4375 - 7/16"); mini. external (outside) radius: 30 mm (1.18") Based on 1 mm thick edge tape. IMPORTANT: ALL min. & max. radii are affected by tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape: Semi or rigid.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Equipped with:Thermal-regulated glue pot heated via (1) 800 Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) of granules. (2) Pressure rollers to copy the shape of the piece, automatic guillotine for coiled material 0.5 mm - 3 mm (0.02" - 0.11") thickness & 57 mm height (2-1/4"). Operator Interface -- Faster processor and a more accurate encoder for more consistent tight butt joints; 15"; touchscreen monitor; training & maintenance videos on PC; connect to the Internet for service and updates; more user-friendly interface. - Bar code capable (optional).The 15"; touchscreen monitor provides an intuitive control panel, while features like training and maintenance videos make it easier than ever to maintain and operate the machine. The optional bar code capability allows for seamless integration into modern production workflows, reducing the potential for operator errors.Features -- Tape height guide; aluminum infeed guides; solid shoe holder; adjustable pod height spindle; digital readouts; pneumatic enclosure; laser upgrade.The new PLC interface enhances usability, while the machine is capable of edgebanding and trimming an inside radius as small as 7/16″. It features 18,000 RPM ER20 collet-type spindles (top/bottom), and the same proven articulating vacuum support arm. The "nVision C1.5" can band and trim open-ended parts up to 8

SNX nVISION SYSTEM G1 CONTOUR EDGEBANDER: -- SpecificationsCurved (Contour) Edgebander allows 360° edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation as Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working CapacityThe" nVision 1" can band minimum material size: 150 mm (6") diameter.Max. material size: 2,400 x 2,400 mm (94" x 94"); Max. material weight: Up to 104.5 kG (230 Lbs).Material thickness from: 10 - 60 mm (0.4" - 2.36"); Banding thickness from: 0.5 mm thin tape w/low temp adhesive to 3 mm tape. -- Radii CapacityMin. internal (inside) radius: 80 mm (3.14"); min. external (outside) radius: 30 mm (1.18"), based on 1 mm thick edge tape. Edgebanding thickness: 1 mm; min. = R 30 mm. Edge thickness: 2 mm; min. = R 50 mm. Edge thickness: 3 mm; min. = R 80 mm. Panel thickness: 10 - 60 mm w/Edge thickness 1 mm. Panel thickness: 10 - 60 mm w/Edge thickness 2 mm. Panel thickness: 10 - 45 mm w/Edge thickness 3 mm.IMPORTANT: ALL minimum & maximum radii are affected by: Tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape: Semi or rigid.Equipped with:Thermal-regulated glue pot heated via: (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) granules. (2) Pressure rollers to copy the shape of the piece; automatic guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (0.125" - 2-1/4"). Features -- Laser for easy length identification with: Closed parts without the need for additional length measurement.Laser detects: Tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.Machine equipped with: Foot pedal for manual control/intervention. Motorized turntable for: Automated edgebanding application to large panels.Holding or support arm with: Large interchangeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Complete with: Top & Bottom Trimming Unit. Centralized Control Panel with: Individual controls for all stations to enable manual feeding of panels if desired. Banding station. Edge band coil stand. Standard size vacuum pod for articulated arm. 80 mm Dia. (3") Dust extraction outlet. Foot pedal activation/deactivation control. Larger feed roller. QC Glue tank with sensor. -- Actual Model: SNX nVISION SYSTEM G1

SNX nVISION SYSTEM G1 CONTOUR EDGEBANDER -- SpecificationsCurved (Contour) Edgebander allows: 360° Edgebanding to contoured (shaped) panels.Edgebanding is applied automatically as part is advanced past the edgebanding workstations via turntable.Reduced learning curve/expertise for operation: Operator simply loads part to vacuum turntable, then activates the edgebanding cycle. -- Working CapacityThe" nVision 1" can band min. material size: 150 mm (6") diameter.Max. material size: 2,400 x 2,400 mm (94" x 94"); max. material weight: Up to 104.5 kG (230 Lbs).Material thickness from: 10 - 60 mm (0.4" - 2.36"); banding thickness from: 0.5 mm thin tape w/low temp adhesive to 3 mm tape. -- Radii CapacityMin. internal (inside) radius: 80 mm (3.14"); min. external (outside) radius: 30 mm (1.18"), based on 1 mm thick edge tape. Edgebanding thickness: 1 mm; min. = R 30 mm. Edge thickness: 2 mm; min. = R 50 mm. Edge thickness: 3 mm; min. = R 80 mm. Panel thickness: 10 - 60 mm w/Edge thickness 1 mm. Panel thickness: 10 - 60 mm w/Edge thickness 2 mm. Panel thickness: 10 - 45 mm w/Edge thickness 3 mm.IMPORTANT: ALL minimum & maximum radii are affected by: Tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape: Semi or rigid.Equipped with:Thermal regulated glue pot heated via: (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) granules. (2) Pressure rollers: Copies the shape of the piece; automatic guillotine for coiled material up to: 3 mm (0.11") Thickness & 57 mm height (0.125" - 2-1/4"). Features:Laser for easy length identification with: Closed parts without the need for additional length measurement.Laser detects: Tight radius and will automatically slow the speed + resume the set speed when the detected radius has passed.Machine equipped with: Foot pedal for manual control/intervention. Motorized turntable for: Automated edgebanding application to large panels.Holding or support arm with: Large interchangeable vacuum pod to secure panels for edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area.Complete with: Top & Bottom Trimming Unit. Centralized Control Panel with: Individual controls for all stations to enable manual feeding of panels if desired. Banding station. Edge band coil stand. Standard size vacuum pod for articulated arm. 80 mm Dia. (3") Dust extraction outlet. Foot pedal activation/deactivation control. Larger feed roller. QC Glue tank with sensor. -- Actual Model: SNX - nVISION SYSTEM G1

SNX - nVISION SYSTEM2 G2. Contour Edgebander + Optional Dual Telescoping Arms for simultaneous Contour Banding & Trimming -- Specifications Curved (contour) Edgebander to allow: 360° Edgebanding to contoured (shaped) panels.Edgebanding applied automatically as part is advanced past the edgebanding Workstations via turntable.Reduced learning curve/expertise for operation as Operator easily loads part to vacuum turntable, then activates the edgebanding cycle. -- Working CapacityThe "nVision" Contour Bander bands a min. material size of: 150 mm (6") dia.Max. material size: 2,400 x 2,400 mm (94" x 94"); max. material weight up to: 104.5 kG (230 Lbs).Material thickness from: 10 - 60 mm (0.4" - 2.36"); banding thickness from: 0.5 mm thin tape w/low temp adhesive - 3 mm tape. -- Radii CapacityMin. internal (inside) radius: 80 mm (3.14"); min. external (outside) radius: 30 mm (1'-18") Based on 1 mm thick edge tape. Edgebanding thickness: 1 mm; min. = R 30 mm. Edge thickness: 2 mm; min. = R 50 mm. Edge thickness: 3 mm; min. = R 80 mm. Panel thickness: 10 - 60 mm with edge thickness 1 mm. Panel thickness: 10 - 60 mm with edge thickness 2 mm. Panel thickness: 10 - 45 mm with edge thickness 3 mm.IMPORTANT: ALL min. & max. radii are affected by: Tape thickness, quality of adhesive, and edgebanding being applied. Radius size dramatically affected by adhesive temperature and quality of edge tape: Semi or rigid. -- Equipped with:(1) Thermalregulated glue pot heated via: (2) 800-Watt heating elements with electronic temperature controls; holds up to 1 kG (2.2 Lbs) granules. (2) Pressure rollers to copy the shape of the piece; automatic Guillotine for coiled material up to 3 mm (0.11") thickness & 57 mm height (1/8" - 2-1/4"). -- Features: TRIAX 3-AXIS Laser System (patented) for tighter butt joints & easy length identification with closed parts without the need for additional length measurement.Laser detects a tight radius; automatically slows the speed + resume the set speed when the detected radius has passed.Machine equipped with: Foot pedal for manual control/intervention. Motorized turntable for: Automated edgebanding application to large panels.(2) "Heavy-Duty" Articulating arms to support the parts during edgebanding & trimming; arms with large interchangeable vacuum pod to secure panels during edging and trimming.NOTE: Panels can be irregular in shape but must conform to the min. tolerances of inner & outer radii and fit within the work area. -- Complete with: Top & Bottom Trimming unit. Centralized control panel with: Simple PLC Touchscreen Interface with individual controls for all stations to enable manual feeding of panels if desired. Banding Station. Edgeband coil stand. Standard-size vacuum pod for articulated arm. 80 mm dia. (3") dust extraction outlet. Foot pedal activation/deactivation control. Larger feed roller. QC Glue tank with

SORBINI TM/95-2F Flow Coater Specifications: -- 24" Coating width, 4" max. thickness, hand crank controls curtain thickness, (1) head gravity feed. -- 2 HP feed motor for variable feed speed from 90 - 350 FPM, (1) 1.5 HP circulating pumps, (1) stainless steel tank & return reservoir. -- Conveyor: 24" Wide, 60" Long at infeed, 72" long at outfeed. 34" long center belt.

SORBINI SMART COATER MF Single Head Differential Roll Coater;SORBINI - Single-Head Roll Coater, ... "SMARTCOATER MF" SeriesMachine Features & Benefits:Single-Head Roll Coater designed for smooth application.Conveyor belt made of: Solvent resistant material with automatic tracking rollers mounted underneath the application rollers (182 mm dia.).Application rollers (250 mm dia.) covered with Heavy Duty vulcanized rubber of different shore hardness for different applications & coating products.Heavy gauge chromed steel doctor rollers (173 mm dia.).Feeding belt, coating rollers, and doctor rollers are all driven by independent motors and inverter is controlled directly from the control panel.Self-leveling floating head for optimum application on uneven surfaces.Thickness control and indicator on the control panel.Different types of scrapers are available according to the coating product and type of application.Pneumatic pump for lacquer feeding and recirculation.Differential capability allows for rotation inversion of doctor rollers and for fine adjustment of the applied coating, particularly important for high quality top coats.Safety "Cleaning Mode" to facilitate and safely service the machine.Technical Specifications:Working width from 0 to 1,300 mm (0 to 51 in).Min. workpiece length: 305 mm (12 in).Speed range: 2 - 11 MPM (6-1/2 to 36 FPM).Power consumption: 4 kW.Compressed air required: 15 Nl/Min (0.53 CFM) exhausted solvent/air mix. Working side: Right.Electric equipment: Explosion proof.Footprint Dimensions: Length 898 mm (35 in.) width 3,282 mm (129 in.) height 1,674 mm (66 in.).

Combination Differential/Filling Machine SMARTCOATER with: 880 mm (34-1/2") Working/pass-through height; one of the best units ever produced. Dual purpose machine can be utilized as: -- 1) A standard differential Roll Coater for application of UV sealer or top coat material; as a differential Roll Coater the 1st application head is independently utilized to for precisely controlled application. -- 2) A Filling Machine for application of H2O or UV filling material to calibrate substrates with porous veneer; as a Filling Machine, both heads are utilized for application and reverse smoothing or pressing of UV filling material.Specifications: -- (2) Heads, 53" width cap. - 1st Head: 250 mm (9-3/4") Dia. rubber coated applicator roller with separate doctor roller; doctor blades are oscillating. -- 2nd Head: 245 mm (9-5/8") Dia. chromium coated smoothing/reverse roller w/separate chromium doctor roll; all heads are floating to compensate for calibration errors & minimize damages from oversize parts. -- Adjustable opening 0 - 100 mm (3-3/4"); thickness protection safety bar connected to pneumatic emergency lifting; EX-proof electrics on all motors. -- 2 HP Conveyor drive: Variable feed speed from 26 - 131 FPM; 1/2 HP variable RPM drive on doctor rolls and separate 3/4 HP drive on applicator & reverse rollers. -- Electrical power: 480 V, 3-Ph, 3.8 kW; 7 Amps.

CEFLA/SORBINI, VS 34/ACT/1600 - Top Only Panel cleaning machineEquipped with:Two (2) Anti-Static ionization bar. One (1) soft horse hair rotating brush, Min. work piece length 290 mm (11.5";).Belt conveyor with variable speed feed from 3 - 16 MPM (approx 10 - 52 FPM). Hand wheel for thickness adjustment.

2022 CNC controller! Under power & ready to demo! 3-Axis CNC Vertical Milling Machine - Seller has outgrown and upgraded to larger capacity CNC Machining Center. - Table size 10" x 50" x 38” H - Travels: X-Axis: 31", Y-Axis: 17", Z-Axis: 23-1/2" - Quill travel 5" - Quill diameter 100 mm (3.94") - No. 40 Spindle taper - Variable spindle speeds 80 - 4,000 RPM - Rapid traverse 150 IPM - Distance from spindle nose to table (Maximum part height) 23-1/2" - Distance from spindle center to column face 19" - Maximum weight of workpiece 1,320 Lbs. - Maximum work capacities: 1" Drilling & Tapping mild steel & Milling (Metal removal rate/mild steel) 5 cu. in./min. - 5 HP Spindle motor - 560 in-oz Continuous torque D.C. servo motors & Precision ground ball screws for X, Y, & Z-Axes - YEONG DIEN Automatic lubrication unit Includes: - 2022 "PROTOTRAK SMX3" 3-Axis CNC Control/3-Axis Digital Readout (Control defines tool path based upon user defined part geometry), with Pentium PC-processor with 512 MB RAM, 10.4? Color active-matrix screen, Touchpad, (4) USB connectors, MICROSOFT "WINDOWS" Operating system, Program feedrate override & Tool path graphics - ALL MACHINE PARTS "MAXI TORQUE-RITE" Pneumatic drawbar, with 40 - 50 ft. Lbs. of torque - EKSTROM CARLSON "MISTIC MIST 1ST-2LC" 1 Gallon Capacity Coolant Mist Generator, with Adjustable air & Liquid control valve - WALDMANN "ROCIA.FOCUS" 600 Lumen 5,000 K Sealed Housing LED Work Light

SPEC AIR Model R-44SQ Dust Collector with Shaker Bag Cleaning, Abort Gate, Spark Detection, Rotary Air Locks and Relay Fan in a closed loop configuration. -- Overall Data: 46,000 CFM with approx. 6170 sq. ft. of cloth area consisting of (286) filter bags operating at 7.4:1 Air-to-Cloth Ratio (ACR). 'Can velocity' (upward) is 211 FPM. Polyester filter bags are 9" dia. x 110" long. -- Fan:/Motor: SPEC-AIR EB-44 Clean Air Fan with approx 44" dia. inlet/outlet, ground- mounted in an upblast arrangement. Fan can deliver 46,000 CFM @ 16" SP. Inspection door, and belt guard. Belt-driven by a TOSHIBA 200 HP High Efficiency (Inverter Duty), TEFC motor, 447T frame at 1780 RPM. -- Bag Cleaning: Via (2) Shaker motors with a lattice of tie-rods inter-connected to each row of bags. Bags are accessed from the top clean air plenum.Timer relay from low voltage controls for bag cleaning. -- Comes with: (2) Tapered hoppers separating the large particles, large access door, Backdraft Dampers adapted to (2) 32" filter inlets, lower hopper bottom each with Rotary Air Lock. Discharge from both RAL's is connected to a Material Handling Transfer/Relay fan into an enclosed container (not included) for continuous collection of waste. A return pipe from container makes this a closed loop configuration. Explosion doors. Safety ladder to top return air plenum.. Magnehelic differential pressure gage to monitor the condition of the filter bags. -- Construction: Heavy gage construction with reinforcing ribs and Flange-bolted in the middle easily allows units to transport into two units, ie 120" x 141".Return Air starts from filter outlet with adaptor to 44" dia. fan inlet. Discharge Silencer of fan outlet has a 44" Abort Gate returns air into building. -- Features: HANSENTEK Spark Detection system. Main electrical panel with pushbottons and controls. -- Includes: Filter housing and outside pipe is fully covered with insulation to minimize heat loss & reduce plant heating cost. -- Overall dimensions: 282"; Long x 120"; Wide x 317"; High. Weight approx. 20,000. Lbs. -- Note: Unit was moved in 2020 to current location, refurbished added installation.

SPEC AIR Model R120-26RD-OC Baghouse Filter Auto Shaker Type Dust Collector Loaded with features. -- Capacity of approx.15,500 CFM based on 7.9:1 Air-to-cloth ratio, with 1,962 sq. ft. or fliter alea and the following features and components: -- EB-26, 60 HP SPEC AIR, Air Handling Fan , 15.500 CFM @ 16" SP mounted in a negative pressure configuration (clean air side) with return air and with automatic 26" dia. Abort Gate Damper according to NFPA-68-69 CODE. 110 volt actuated by the Spark Detection System. -- HANSENTEK AN104 Spark Detection/Suppressions system Per NFPA 64-68 and c/w BPS-9X4 Booster Pump & FLEXCON P2P20 Tank. -- 1,961 sq. ft. of filter area using (97) high efficiency Polyester bags. Operating at 7.9 to 1 ACR (Air to cloth ratio). -- 26"; Diameter Inlet & outlet duct. -- Tangential inlet with Backflow Damper, according to NFPA-68 CODE. -- Top mounted motorized bag shaker. mechanism powered by 1.5 HP. -- Rotary Air Lock with 96" clearance. (4) leg support steel frame & Safety access ladder. -- Explosion Venting Doors, according to NFPA-68 CODE. -- Filter Bag size approx. 9" dia. x 9' long, -- Inline 26" dia. Silencer muffler on return air duct. -- Ground mounted Belt Driven Fan complete with TEFC motor and inspection door. -- Features: 60 HP Soft Start Controller. -- ENGINEERED ELECTRIC Control Panel with starters and controls. -- Manometer gauge to monitor differential pressure (life) of filter media. -- Housing/Support Steel dimensions: 120" long x 120" wide x 32' high. Approx. 13, 500 Lbs. -- Some pictured pipe is included.

SPROUT 7.5' X 24' DRYER (ROTARY DRUM) + GAS BURNER:Complete with the following components: -- 7.5 Ft. x 24 Ft. Steel Rotary Dryer Drum. -- Natural Gas Burner (may be converted to LP) with 13.5 Ft. Refractory Lined Furnace Tube. -- Belt Drive with Gear Reducer and Electric Motor. -- Trunnion Bases complete with Forged Trunnion Wheels. -- Forged Trunnion Tracks (weld-on style) ...look like new. -- Vertical drop material Inlet Transition with Side Access Door. -- Rated for approx. 2 TPH water evaporation or about 4.5 TPH wood sawdust input. -- OPTIONAL ITEMS: Receiving Bin with Airlock and Screw discharge Conveyor. Material Input Screw Conveyor. Main Fan.

SQUARE D - 75T3H: 75 KVA; 480 - 208 V; 3-Phase Autotransformer Specifications: -- Intended for power, heating, and lighting applications. -- Enclosure Rating: NEMA 2. -- Multi-Tap (432 - 504 V) Primary 480 V (Delta); Secondary 208Y / 120 V @ 60 Hz ventilated. -- Aluminum windings. -- UL Listed. (2) Available; price per unit. - Make offer for both!

SSI Model - 1000-E, Slow Speed, High Torque ShredderSpecifications: -- 50 HP Motor; twin shafts; 40" x 25" ChamberIncludes: -- Stand, feed hopper; controls

STANMAC SPRAY 300 Moulding Sprayer The Stanmac "Spray 300" is ideal for linear profiles in a wide range of materials and capable of utilizing both waterborne and solvent-based coatings including stains, paints, and lacquers.Spray guns are automatically timed for the start and stop of the spray cycle to ensure the best spray efficiency. The overspray is captured by the spray trough and can be recovered while atomized spray is captured by fiberglass media and clean air is exhausted from the spray cabin.Can be fitted with spray gun packages to include conventional, air-assisted airless, and airless to suit your requirements.Specifications: -- Workpiece max. width: 12"; -- Workpiece min. length: 30" -- Feed Speeds: 30 - 150 FPM -- Feed Motor: 0.5 HP -- Extraction Fan: 3.0 HP -- Number of Spray Guns: 3 -- Recovery Troughs 1 -- Spray Gun Trigger: Electronic Switch -- Piece Counter: Digital -- Filter Media: Replaceable fiberglass media