DUSTEX W-2500 Whispurr 5-Bag Dust Collector. -- 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Collection hopper w/ rotary air lock,

DUSTEK W-2500 Whispurr 5-Bag Dust Collector.Specification: 8,500 CFM; 25 HP ultra quiet, self-contained high efficiency internal return (5) bag dust collector; 16" Dia. inlet, dynamically balanced impeller. -- Unit includes: (5) 60" filter bags, straps, gaskets, magnetic bag holders. -- Includes: Magnetic starter.

DUST-EX HSAG-24 Packaged Safety Solution for a 22"x22" (24" dia. round equivalent) Return Air Rated for 10,000 CFM. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap Valve (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel. One-Zone CP05 Control Panel 1 inlet, 1 outlet: UL698A Control Panel for use with NFPA 69 compliant Explosion Isolation Valves. Standard panel includes status lights, intrinsically safe circuit (1 Per Zone), monitored inputs (3 total), ability to add a secondary clean air isolation valve, output for system shut down and monitoring, drawings, installation instructions, NEMA 4 outdoor rated enclosure, UL and Canada UL listings. Allows for 120VAC or 24VDC input power. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 39" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) High Speed Abort Gate, EM-HSAG02-24, magnetic (24 VDC), 22" x 22" flanged inlet and outlet (24" round equivalent), control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 10,000 CFM / 3000 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe

DUST-EX HSAG-24 Packaged Safety Solution for a 23"x23" (24" dia. round equivalent. Suitable for up to 25" dia. ) Return Air Rated for max 12,850 CFM @ 3,500 FPM.. System for mitigating fire and explosions in combustible dust environments, for the woodworking industries. Generally includes Heavy Duty Abort Gate, Non -Return Valve and Spark Detection/Suppression Hardware and Controls as follows: -- 1.) VigiFlap Dust Sensor, Dirty Air 22": Sensor, dust level, adjustable capacitive for organic dust, requires intrinsic safety system (will not trigger combustion or ignition in gasses or fuels). -- 2.) VigiFlap Explosion Isolation Flap (Non-Return) Valve, EV-VF22 (EPDM); 22" diameter, flanged inlet and outlet, locking mechanism; welded steel construction, safety red painted finish, domed flap (stainless steel), inspection/access door, EPDM gasket, grounding straps, inductive shutdown sensor, normally open or closed flap orientation, certified ATEX EN 16447, NFPA 69 compliant. -- 3,) Control Panel, Intrinsically Safe, CP05 - single zone, allows for installation of (1) inlet and (1) outlet explosion isolation valve(s), (3) monitored inputs per zone (two programmable), (1) intrinsic circuit with barrier and physical separation (one per zone), outputs for system shut down and monitoring, NEMA 4 enclosure, 120 VAC or 24 VDC. -- 4,) SPARK DETECTION & EXTINGUISHING, SINGLE ZONE, KIT for pipe sizes 20?- 40? diameters; includes Raptor Spark RS-CUSP1L Control Panel, (2) Spark Detectors, Extinguishing Kit, Flexible hoses, Audible Alarm & Warning Light. Single zone spark detection and extinguishing kit for duct sizes of ?20" - 40" diameter, RS-KIT02, includes Raptor Spark RS-CUSP1L control panel, (1) RS-PDK-02 packaged detector kit with (2) spark detectors with mounting kits, (1) RS-PWE02 water extinguishing assembly with hose connections and spray nozzles, audible alarm, warning light, battery back up - ATEX certified, CE listed, FM approved. -- 5.) Packaged External Test Lamp Kit, RS-TLK02, duct sizes: 6" - 39" diameter, (2) RS-SD02 test lamps with (2) RS-MK02SD/TL mounting kits - IP 65 enclosure, ATEX certified, CE listed, FM approved. -- 6.) Optional Start up Service Assistance: a.) Start Up - Day Rate @ $1,750/day. b.) Travel Service: Day Rate @ $900/day. c.) Travel Expenses: Total $110/hr. - min. two hrs. required - total $220. c.) Start Up Service Hourly Rate is $160/hr. Min. (4) hrs. needed for a total $640. -- 7.) Heavy Duty High Speed Abort Gate, RGAG-23, magnetic , 23" x 23" flanged inlet and outlet (24" round equivalent), suitable for 21" - 25" dia., control panel for, magnet power with status lights and manual test button, gate position verification monitoring, manual reset lever, weather hood with bird screen. Maximum volume and velocity: 12,850 CFM @ 3,500 FPM, clean air installations only, NFPA compliant when installed with listed spark detection system. -- 8.) Packaged dust probe (broken bag detector) RS-PDP03, RS-MK02DP, etc. IP 65 encl

GANNOMAT INDEX 280 TREND CNC BORE, GLUE & DOWEL INSERTER: -- Specifications:CNC Controlled horizontal Point-to-Point Drilling, Gluing & Dowel Inserting Work Center for absolute, incremental, variable (parametric) programming of boring patterns. -- Working Field(4) Independent zones for individual processing of (1 - 4) pieces. Pneumatically activated Stop system (side fences) consisting of: Right-hand, left-hand, and center stop. Max. single part Length 2,800 mm (110"). As a 2-zone: LH & RH is 1,400 mm (55") each part. As a 4-zone with center fence: LH/RH is 700 mm (27.5") each part.Min/Max. Material Thickness 0.50" - 3.125" "X" Axis Positioning Speed 246 FPM (75 MPM) and driven by rack & pinion for fast acceleration/deceleration of working unit. "Y" Axis is set by mechanical digital counters. "Z" Axis is NC controlled height adjustment for boring/inserting units. -- Hold-down Clamps:Total of (10) pneumatic, "quick change" Hold-down Clamps. -- Dowel driving & horizontal boring:Integrated into (1) station; the Dowel Driving Unit is located alongside the Boring Station; both units are mounted on (1) support. -- Horizontal Drilling Spindle:Can be setup for 6 - 8 or 10 mm; dowel length from 25 - 50 mm. -- Doweling Station includes:Vibrating hopper with: (1) Single drop device and (1) outlet tube; insertion head & dowel driving with air impulse.Mechanical dowel diameter & dowel length control prevents the insertion of any oversized dowels. -- Glue Valve/Amount:Controlled via software and can be adjusted by milliseconds; (2) standard separate stainless steel 1.5 gal. pressurized tanks (one for glue, one for water to clean/purge the glue tubes. -- Operator Interface:GANNOMAT + BECKHOFF "C3640 Twincat" PLC Operating System.15" Touch-Screen color monitor; network card (for online operation); serial, parallel, USB ports. -- Actual model is: GANNOMAT INDEX 280 TREND. NOTE: Machine is currently setup for 8 mm dia. x 35 mm long dowels.

GANNOMAT INDEX 470 TB CNC BORE, GLUE & DOWEL INSERTERSpecifications: -- The GANNOMAT "Index 470 TB" is a CNC Controlled Point-To-Point Drilling/Gluing/Dowel Insertion Machine for variable programming of boring patterns. -- "X" Axis CNC Controlled via precision ball screw Servo drive; "Y" & "Z" Axis adjusted via mechanical spindles; set by manual digital indicators.Working Width: -- 1,300 mm (51") x 3/4" to 7-3/4" Width x 1/2" - 3-1/8" material thickness with: (2) Fields; LH/RH (mirror image). -- (8) Vertical holddown cylinders for horizontal part processing. -- Dowel driving & horizontal boring integrated into 1-station; the dowel driving unit is located alongside the Boring Station; both units are mounted on (1) support. -- Horizontal Drilling & Boring Station head setup for: 6 - 8 or 10 mm; Dowel length from 25 - 50 mm.Dowel Station includes: -- Vibrating hopper; insertion head & dowel driving with air impulse; setup for 8 mm dia. x 50 mm long dowels. -- Glue valves controlled individually at Control Cabinet; central adjustment for the amount of glue by means of digital timer.Operating System: -- MS-XP & GANNOMAT Production software; 15" color touchscreen monitor interface, USB drive, bar code capable, Controller & Drive:BECKHOFF "C3620 TWINCAT V2.10".Complete with: -- (1) Glue tank, (1) water tank, auto lubrication system.

GEHL DL10L-44 4x4 TELEHANDLER Specifications: -- John Deere 4-Cylinder Turbo Diesel EngineFeatures: --10K Lbs Lifting Capacity; Hours: Approx. 4,000

GENERAL - 350 10", ...Tilting Arbor Table Saw with: 5 HP Motor & Rip FenceSpecifications: -- Table size: 20" LR x 28" FB x 34-1/2" H. -- Arbor dia. 5/8"; tilt 0° - 45° to right; blade speed: 4,000 RPM. -- Max. depth of cut: 3-1/8" at 90°; 2-1/8" at 45°; max. width of dado cut 13/16". -- Max. rip cap.: 52" Right.Equipped with: -- 8" Left & right table extensions. -- 5 HP Motor.Complete with: -- DELTA "Unifence Saw Guide"; 43" L x 3-1/2" H Rip Fence System. -- Blade Guard. -- Miter Gage.

GENERAL KINEMATICS Para-Mount II Single Deck Rectangular Vibratory Screener;Complete with the following features: --Model STM 96 X 20. --Carbon Steel. --Nominal screen size 96" wide x 20 long x 15" deep. --Designed for Trona mineral at a feed rate of 700 tons per hour at 80 pounds per cubic foot bulk density. --Driven by (2) 15 HP top mounted drives. --Current screen: Approximate 1" x 1" square openings. --Base mounted. --Overall dimensions: 290"L X 130"W X 90"H

GENOX V600 New Single Shaft ShredderIn Stock - Ready to Ship!Features --Shock Absorbing Gearbox that reduces stress on Drive Components -- 25HP -- Hopper Opening - 48" x 43" -- Rotor Diameter - 9" --Rotor Knives that can be used on four edges before replacement. --Durable Counter Knives that adjust to maintain cutter clearance --Quick Change Screens for accurate particle size control --Segmented Shredding Chamber Floor with Brass Guides --Twin Speed Hydraulics with an integrated air cooler --Stand Alone Electrical Control Panel with Siemens PLC Control System --Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GENOX V800 New Single Shaft ShredderIn Stock - Ready to Ship!Features: -- Shock Absorbing Gearbox that reduces stress on Drive Components -- 50 HP motor -- Hopper Opening - 59" x 56" -- Rotor Diameter - 15.75" -- Rotor Knives that can be used on four edges before replacement. -- Durable Counter Knives that adjust to maintain cutter clearance -- Quick Change Screens for accurate particle size control -- Segmented Shredding Chamber Floor with Brass Guides -- Twin Speed Hydraulics with an integrated air cooler -- Stand Alone Electrical Control Panel with Siemens PLC Control System -- Tested, Approved and Certified to the applicable CE safety standardsTypical Applications --Plastics --Wood --Cable --Paper --Aluminum --Foam --Textile

GENSCO - DTX 200: 8" Alligator Shear -- Blade Length: 8". -- Foot pedal control.

GIARDINA DUALTECH 605 Automatic Reciprocating Sprayer:GIARDINA, model DUALTECH 605. Automatic reciprocating Spray Machine.System includes: -- In-feed roller conveyor with panel reading/detection 60-cell photodiode bar to monitor and regulate spray application, further maximizing application transfer efficiency. -- (2) Reciprocating trolleys with spray gun supports, and adjustable speed, providing a consistent speed and pattern across entire conveyor width. - Each trolley to carry (4) adjustable guns on each head (8 guns total). -- Two (2) coating circuits, suitable for solvent and water-based coatings. -- Motorized height adjustments of spray gun supports. -- Spray guns are independently adjustable in inclination; and manual adjustment. -- Through Feed Conveyor: Max. working width of 1,300 mm (51"), variable speed adjustable by means of an inverter. -- Synthetic Belt Conveyor: Ring-closed by means of an "overlapped" joint and with solvent-resistant surface treatment.Features: -- Total recovery of the lacquer deposited on the belt and cleaning of the belt with the possibility of reusing it in the spraying circuit. - Rapid repositioning of the conveyor belt system thanks to the special design of the frame. -- Air exhaust system and separation of the solid content from the air by means of two (2) suction boxes located on the two sides of the conveyor, equipped with high-efficiency twin Dry-Filters. The filtered air is exhausted to the outside by means of a centrifugal fan. -- The Enclosure Booth is made with structural irons and coated sheet steel panels. -- Control and set-up of the work parameters by means of a PLC located on a pivoting arm mounted to the machine.NOTE: Is being "Cleaned, checked and Serviced" by on of the most experienced Finishing Equipment Technician!

GIBEN - G2 GENESIS 48: CNC Router (ATC & Boring)4' x 8' Fixed table; moving gantry machine with: Single zone vacuum table. -- Equipped with:(1) 12 HP ISO-30 Type ATC spindle; air-cooled; ceramic bearings; variable spindle speed from: 6,000 - 24,000 RPM. -- 6-Station Automatic Tool Changer & 2 HP 9-spindle vertical drill bank (5 in X- & 4 in Y-Axis). -- Axis Stroke1,300 mm (51") In Y-Axis; 2,500 mm (98.4") in X-Axis; 200 mm (7.8") in Z-axis. -- Max. Feed Rate60 MPM (2,362 IPM) In X- & Y-axis; 30 MPM (1,180 IPM) in Z-axis. -- Equipped with & FeaturesTool Length Measuring System (Tool Touch Off device). -- ControlANDI/SYNTECH Controller with: Network compatible WINDOWS PC based front-end; color monitor; keyboard; mouse.Full function handheld pendant absolute & incremental programming; cutter & tool length compensation; feed rate & spindle speed override; inch/metric operation; linear/circular & helical interpolation. -- Complete with:10 HP BECKER Vacuum Pump; Tool Holder’s collets; Light safety fences. -- Maintenance supplies: Grease, grease guns; full manuals; product literature.

GIBEN - G4 EVO 510: CNC Router (ATC & Boring) + Rake & Offloading -- Specifications 5' x 10' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working Capacity:X-Axis 126" (3,200 mm); Y-axis 62.9" (1,600 mm); Z-axis stroke is 9.8" (250 mm); max. material thickness 4.7" (119 mm). -- Positioning Speed X- & Y-Axis 262 FPM (80 MPM); Z-axis 98 FPM (30 MPM). X- & Y-Axis use a precision Rack & Pinion system; Z-axis uses precision ball screws. All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors. All motion components are maintained by an automatic lubrication system. -- Work AreaFlat table design with: "Matrix" grid phenolic surface for "Nested Base Manufacturing". (2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; automatic NC controlled 8-zone vacuum table. Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward-shaped parts; with: "Quick Connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit (1) 2.5 HP (1.7 kW) Motor; variable speed up to 6,000 RPM; "HSD" Boring unit. (9) Independent vertical spindles with: (5) In X-axis & (5) in Y-axis. -- Machining (1) 15 HP Air-Cooled "ANDERSON" Electrospindle with: HSK F63 Adaptor; RH & LH rotation; variable speed from 1,000 - 24,000 RPM. (1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control PC Front-End with: ANDI/GIBEN "SYNTEC" + "WINDOWS" Operating System. 19" LCD Flat screen monitor; server; full keyboard; mouse: All mounted on a mobile cart. Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. Automatic program update according to the tool length (touch-off probe).Equipped with: Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is: GIBEN - G4 EVO 510NOTE: No vacuum pump included.Tear down and loading not included.

GIBEN - G4 512, ...CNC Router with ATC and Boring: 5' x 12' "Matrix" grid Phenolic surface for "Nested Base Manufacturing". -- Working capacity:X-Axis 145.6" (3,700 mm), Y-axis 62.9" (1,600 mm), Z-axis stroke is 9.8" (250 mm), max. material thickness 4.7" (119 mm). -- Positioning Speed:X- & Y-Axis 262 FPM (80 MPM), Z-axis 98 FPM (30 MPM).X- & Y Axes use a precision Rack & Pinion system, Z-axis uses precision ball screws.All axes movement is on precision linear guides & ways and controlled by digital, brushless AC Servo motors.All motion components are maintained by an automatic lubrication system. -- Work area:Flat table design with "Matrix" grid phenolic surface for "Nested Base Manufacturing".(2) Side clamps + (4) external pneumatic pop-up stops for piece positioning at (4) corners of workstations; Automatic NC controlled 8-zone vacuum table.Prepared for (optional) "quick fit" vacuum outlets for optional clamping of small or awkward shaped parts; with "quick connect" vacuum outlet for custom vacuum pods & fixtures. -- Boring Unit:(1) 2.5 HP (1.7 kW) motor, speed 6,000 RPM, "HSD" Boring unit.(9) Independent vertical spindles with: (5) in X-axis & (5) in Y-axis. -- Machining:(1) 15 HP/18 HP peak Air-cooled "ANDERSON" Electro-spindle with: HSK F63 Adaptor, RH & LH rotation; variable speed from 1,000 - 22,000 RPM.(1) 8-Position ride-along ATC tool changer for "on the fly" ATC. NC Controlled "touch-off probe" tool presetting for the measurement of the tool length. -- Operator & Machine Control:PC Front End with ANDI/GIBEN "SYNTEC 21MA PC based Controller" + "WINDOWS" Operating System.19" LCD Flat screen monitor; Server, full keyboard, and mouse all mounted on a mobile cart.Intel(R) Core i CPU; 8 GB RAM memory; 500 GB (SSHD) hard disk; Dedicated graphic card; DVD reader; USB ports; Ethernet card for network connection capabilities. -- Complete with:(2) 250 cbm/Hr (9 HP) "BECKER" vacuum pumps, tool holders, Collets, tool changing stand and manuals. Automatic program update according to the tool length (touch-off probe).Automatic Lubrication system for linear guides, pads, and recirculating ball screw. Teleservice capabilities; perimeter Safety light bars & perimeter fencing; Manuals & Documents on CD. -- Actual Model is GIBEN - G4 512. Machine footprint Floor area 472"; x 197";

GIBEN - ICON FAST 105 SP 3300: Front Load, Automatic Panel Saw -- Specifications 129.9" (3,300 mm) Overall cutting length; 131.8" (3,350 mm) pusher stroke; 4.1" (105 mm) max. saw blade projection; 30 HP (22.3 kW) main saw motor; 2 HP (1.5 kW) scoring saw motor. -- Saw CarriageVariable saw carriage speed from: 0 - 492 FPM (0 - 150 MPM); return speed 492 FPM (150 MPM).Rack & pinion drive, driven by AC brushless Servo motors. -- Pusher FenceElectronically controlled overhead program fence with: (7) pneumatic gripper clamps; grippers open to 4.6" (117 mm).Forward pusher speed: 3.2 - 262 FPM (1 - 80 MPM); return speed: 62 FPM (80 MPM).Rack & pinion drive; driven by AC brushless Servo motors. -- Operator & Machine ControlPC Front-end with; GIBEN "G-Vision" + "Windows" Multitasking Operating System with: Easy programming of very complex cutting patterns.15" Flat screen monitor displays REAL-TIME graphics of: Cutting dimensions & patterns; program cutting list; manual cuts; diagnostic & online help.Data input by adjustable keypad pendant; standard industrial keyboard, mouse & CD-ROM drive; direct downloading from office PC is possible.GIBEN "G-Vision" guarantees: Fully automatic management of cutting patterns by optimizing all machine movements (pressure beam, saw carriage and side aligner pusher positioning, etc.).GIBEN "G-Vision" includes: Onboard optimizer, which can be accessed at any time directly at the machine.The numerical control adjusts the optimum saw blade projection for the stack of panels being cut and sets the most appropriate cutting speed, in relation to the stack itself, and when necessary to the width of trim cut, too. -- Rear of Machine(9) Rear support rails with: 80 mm Dia. roller modules; rear of machine enclosed for safety. -- Front of Machine(2) Independent automatic side/crosscut aligning device with: 2-3/4" - 49.2" (70 - 1,250 mm) stroke.90" (2,300 mm) Long crosscut fence (front-to-back); (4) front mounted air floatation tables, 20" x 78" (510 x 2,000 mm). -- Complete with: "Quick Change" saw blade system; "REMOTE" electronic scoring adjustment. -- Actual Model: GIBEN - ICON FAST 105 SP 3300

GIBEN - KG-320, ...Edgebander (Compact)0.4 - 3 mm Edge thickness capacity min. panel width 80 mm; panel thickness 10 - 60 mm; variable feed speeds: 12 - 20 MP; electronic adjustment of the upper pressure beam.Equipped with: 2 kG Glue pot & adjustable pressure roll section with: (1) Driven roller and (3) idler rollers.Workstations -- 2-Motor end Trimming Unit. -- Top & Bottom radius Fine Trim Station. -- Top & Bottom Buffing Station.Complete with & Features: -- Programmable PLC Control. -- Sound cabin for all workstations. -- Adjustable outboard panel support.

GIBEN KG-468-JKS EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): -- Specifications:Working Capacity: 0.4 - 3 mm Edge thickness capacity; minimum panel width 80 mm; minimal panel length 120 mm; panel thickness 10 - 60 mm adjustable feed speeds 10/15/20 MPM; motorized adjustment of the upper pressure beam. -- Equipped with: PREMELTING Glue System with: Quick change glue pot; top pot capacity 5 kG (11 Lbs); lower pot capacity 2 kG. -- Adjustable pressure roll section with: (1) Driven roller and (3) idler rollers.Workstations: -- 2-Motor Pre-milling Unit with independent adjustments. -- 2-Motor End Trimming Unit. -- Top & Bottom rough trim station. -- Top & Bottom radius fine trim station. -- 2-Motor Corner Rounding Unit. -- Top & Bottom profile scraping station. -- Top & Bottom flat scraping station. -- Top & Bottom Buffing station.Complete with & Features: -- "DELTA" PLC Control. -- Sound cabin for all workstations. -- Adjustable 700 mm outboard panel support. -- Actual Model is: GIBEN KG-468-JKS

GIBEN KS26J Edgebander with Pre-Milling & Corner RoundingSpecifications: -- Edge thickness 0.4 - 3 mm. -- Minimum panel width 80 mm, Panel thickness 8 - 50 mm. -- Feed speed 16 MPM, Mechanical adjustment of the upper pressure beam.Equipped with: -- 2 Liter Glue Teflon coated tank with Quick heating system. -- Adjustable pressure roll section with (1) Driven roller & (3) Idler rollers.Workstations: -- 2-Motor Pre-milling unit with Diamond tooling and with Independent adjustments. -- 2-Motor End trimming unit. -- Top & bottom trim station with diamond radius tooling . -- Double motor Corner Rounding unit. -- Top & bottom radius scraping station. -- Top and bottom Buffing unit.Complete with: -- PC Touch screen control. -- Sound cabin for all workstations. -- Adjustable outboard panel support.