Northtech MRS-12N Gang Rip 50 HP Motor Needs a new safety with on the door

Manufacturer’s Specification - 15HP Motor + 1HP feed motor (with Wye Delta soft start) - Mechanical variable speed (45' – 100' FPM) provides a speed range for all material types and thickness ranges of 3/16”- 3-1/2”. - Bottom & top kickback fingers - Rack and pinion fence for precise and quick positioning. - Digital electronic oiler provides maximum chain and race life. - 15-1/2? distance from column to blade. - 8' glue line tolerance.

16 HP 12 filter bags up 4 collection bags lower Lots of pipe

Northtech MRS-14-DXL 460v Manufacturer notes: This is a very popular machine and cost effective. New open ended design allows for you to cut wide material up to 27-1/8? wide. Plus spare arbors, lasers, and the optional quick locking, easy to adjust infeed will not break the bank. The Northtech heavy-duty 50 HP multi-rip (“gang-rip”) saw with 15? maximum blade diameter quickly and accurately cuts material up to 4-15/16? thick and 27-1/8” wide. Cutting both sides of your blanks at once provides incredible parallelism, reducing required moulder allowance, and increasing your yield. Laser guides (one included) and an optional 103” fence make proper alignment of even the longest material simple and precise. Variable feed speeds of 25 – 120 FPM and powered height adjustment further improve operator efficiency.

Nova Dry Kiln 26’ wide x 25’ deep holds 5500-12000 board feet propane or Natural Gas fired

Nyle L500 Kiln (High temperature system)

Nyle Firewood Dry kiln No chamber included

Optimal 4-Side Canter See photos fro complete specs

Pallet Chief PC IV With Deluxe Stacker Very Good Condition Recently Removed From Service

This machine was purchased as "rebuilt" by the manufacturer and never put into service at the current location. Ready to load.

Pallet Repair System Disc Dismantler Pallet size: 3.875" Stringer Width Max. (.098 m) 1.25" Deckboard Thickness Max. (.031 m)

Paul AB920 Rip Saw Scanning Fenceless Infeed Infeed & Outfeed (not including decks) The machine has one fixed and 2 moving blades. The minimum distance between the moving blades is 44 mm (1.73"). The maximum distance between the moving saw blades is 210 mm (8-1/4"). The machine is designed for incoming boards with the following min./max. dimensions Length: 4' - 16' Width: 2" - 19" Ripped widths: 1.75" - 8" Thickness: 1" - 2" 480 Volt, 60 hz., 3 phase electrics 75 HP main motor Automatic edging separation after the saw Feed speed up to 300 fpm Fenceless infeed system with automatic skewing capability 16 width sensors on the infeed system

Peerless Chip Bin MOD 14

This machine was reported to be in running condition when removed from service. Looks like a Pendu. Cannot find a plate on the machine to confirm. this is a single arbor gang and it does not have a sizer. 75 HP Main Motor 5 HP Drive motor

Pendu Stacker No hydraulic pack

Good Condition Infeed Hydraulic Power Unit Stacker

Pendu 52" Log Merchandising Saw Model 1300 Chop Saw 60 HP Main Motor 18" Max material capacity Holding Clamps: Spring Loaded No infeed or outfield deck included Available approx June 1, 2025

Selling as a complete package: Pendu Sharp Chain Scragg (2) 100 HP Motors with soft starts Infeed System Log turner Operator Cab All controls and electrical (2) Log Decks: 3-Strand and 4-Strand Pendu bark conveyor: 30'4" Long with 180 degree tail section, 17" flights 2" high, flights spaced 18-3/4" apart Barn Sweep: Elevated conveyor: 25'4 Long, (2) Hold downs with idlers, chain has 17" flights that are 2" high, leg brackets, Approx 90' of Barn Sweep conveyor with chain and drive motor

The seller has confirmed that this Pneumafil 135 is available. Pneumafil Dust Collector Model 135 (13.5-460-8) 150 hp. The round duct enters the collector at 40" diameter & exits at 64" square

Pneumafil Dust Collector Model 135 (13.5-460-8): 150 hp. The round duct enters the collector at 48" Diameter. Dixie Air Dust Collector: Size: 108-12, Type: SPB, 50 HP, Inlet to the motor, circumference is 90".