MLS Number 12231702 2011 Clarke's Industries Bag House ? Explosion doors ? Abort gate at outfeed ? Abort gate at infeed ? Backdraft damper at infeed ? Spark detectors on infeed and outfeed lines ? Airlock ? Backdraft Damper on dust outfeed line ? Deluge System This baghouse is fed from a fan that has suction from Edger, 6”-10”-12”-20” Ukiah (chip/saw) and 20” sawbox. The sawdust from the discharge line under the airlock of the baghouse is sucked into Discharge blower (See Item#2). The dust outfeed line at the middle of baghouse, which discharges the dust fines during the cleaning cycle of bags, returns the fines to the baghouse fan. The Baghouse supplies air back into the building. This baghouse is fed from a fan with following specs: OEM & Model: Clarke’s Industries, Model MH-11, Serial 11OCWUBI3923 Driver: TECO 350 HP, 1785 RPM, 5009C Frame Motor Capacity: 66000 CFM Spark Detection Control System OEM/Model: Clarke’s Industries, Pyroguard CXC-2 Buyer responsible for dismantling.

MLS Number 10679774 Cook Grade Lumber Resaw 30 HP Will saw 16" wide No return 1 1/4" to 2" blades

MLS Number 11413038 Cooper Overhead End Dogging Scragg With Debarker And Gang Edger Transfer Chain Conveyor x 60’, H82,1-7.5 HP 480V gear drive 54" Cut Off Saw, 20 HP 480V motor, hyd stop gates, 20 HP hyd pack 4 strand x 12' long Debarker In Feed Deck, 5 HP 480V gear drive, H78 16” wide x 19’ long log haul belt conveyor (driven from debarker in feed tire drive) Cambio 24" Debarker, 75 HP 480V drive, spiked in/out feed rolls 20 HP 480V drive 3’ wide x 36’ long hour glass rolls transfer, 7.5 HP 480V gear drive 5-strand Scragg in feed deck x 20', H82, hyd log stop loader, 7.5 HP 480V gear drive Cooper Overhead Scragg Mill, 30 HP 480V 150 gal hyd package, variable speed cable drum feed works with pantograph arm Log positioning rolls on infeed w/ double overhead dogging system, 48” dia. saw husk(125 HP 480V each saw), setworks control 2-18” wide 2-position slab and side board belt conveyors, operators control cab w/ controls, camera and monitor for centering log 8-16’ length capacity, maximum log dia. 22”, largest square cant 12” x 12”, smallest square cant 4” x 4” 5-strand lower camel back landing transfer x 9’-6” long, 4-strand hyd lift transfer to gang edger and cant center bypass Center bypass rolls and belt conveyor to edger out feed landing transfer 10” mainland gang edger w/ 200 HP 480V drive,34” inserted tooth saws with 5/16” kerf(24 spare saws with collars), 2-2-2-4 spacing 6” x 50” mainland board edger w/ 150 HP 480V electric drive, 24” inserted tooth saws with 5/16” kerf, 8”-4”-4”-10”-6” pockets, 7-individual actuated self tailing belt conveyor out feed c/w splitters Camel back transfer,4-strand x 27-1/2’ long, H78B, 5 HP 480V gear drive 2-Saw Trimmer, 4-strand x 10’ long, 16’-4” between 20” dia. saws,10HP 480V drive on feed works and saws, 16” wide x 28’ long out feed belt conveyor, 5HP 480V gear drive 4-strand x 26’ long H78 camel back transfer w/ 5HP 480V gear drive

MLS Number 13476937 2010 Cooper Overhead End Dogging Scragg Mill Cuts 6-16ft lengths Control Cabinets and starters Cab with joysticks, scanning and computer controls linear bearings for shifting saw husks 56 inch circle saws Two 150 HP arbors Off bearing drop belts 3 way separator outfeed roll case Includes $25,000 in spare parts Removed from service February 28, 2025 Ready to load

Cresswood Model EF 50-100A Horizontal Shredder 100 HP 12' Vibratory Conveyor (2) Feed Rollers Screw Auger Discharger Inclined Conveyor with 10" Magnetic Head Pulley Discharge Height 116" Crossbelt Magnet Soft Start Extra Set of Cutters 2 New Screens 1/2" Screens

?Cresswood EF-60 Grinder 100 HP 60” Wide Feed Opening Includes 60”W Vibrating Conveyor (shaker table)

MLS Number 10682943 DIEHL SL52 STRAIGHT LINE RIP SAW Bottom arbor 4-1/4"X8-1/2" capacity 15 HP 3,545 RPM arbor drive motor Infeed speed up to 200 FPM Serial# 10/88M-5312-4728 Voltage: 460/60/3 phase Amps: 21.7 Wiring diagram # 2-9000-0026 Was removed from service in November 2020

Diehl SL50 Straight Line Rip Saw 240 volt 3 phase Variable speed control SN: 51108

MLS Number 10689968 Globe 5 Head Panel Trim Saw Approximate panel capacity: 8 feet wide X 26ft long Saw was cutting large full size sheets (8ft+ x 26ft) at a particle board manufacturer Lugs on chains have micro adjustment bolt ( brass) Air cylinders raise and drop heads Brands of chain: Woodward & White Overall width: 14 ft. 6inches Overall height: 6 ft. Overall length: 33 ft. 4 inches+-

GO FAST DD79 DEDUSTER High Speed Board Deduster 230V 3Ph

Ingersoll Rand Air Compressor 3 phase 10 hp Work ready

54" Horizontal Resaw Wide Blade Excellent Machine 400K Replacement Cost

54" Wide Band Resaw Complete Run Around Support Equipment Removed And Ready To Load

MEREEN-JOHNSON 424 DC GANG RIP SAW 24 inch width capacity 75 HP arbor motor- 3600 RPM direct drive 5 HP variable speed feed ( new belt ) Four ( 4 ) kick-back finger sets : ( Two ( 2 ) top in-feed, One ( 1 ) bottom in-feed, One ( 1 ) top out-feed ) A new out-board arbor bearing assembly New set of alum bars and rubber slats installed It is wired 480 volts 3 phase . The serial no. is MJ-4709 One saw sleeve and set of spacers ( 6 saw blades ) Cleaned, painted, and checked.

2022 Morbark 3000XT Horizontal Grinder -180 hours -575 hp CAT engine -Remote -Still under warranty NEW NEW NEW

2022 Morbark 3000XT Horizontal Grinder -500 hours -(C-15) 600 H.P -Like new unit

2018 Morbark 3400XT Wood Hog Horizontal Grinder CAT C18, 765 Hp engine Approx 2100 hours New belly belt/skirting; Rebuilt mill Engine has new cylinder sleeves with rod & main bearings, purge pump & hydraulic fan motor (replaced by manufacturer due to a defect) Remote Magnet 1” & 5” screens Great machine and ready to go to work

2018 Morbark 1300B -3800 hours -C-27(1050H.P) -Tight and dry -Has grinded mostly soft wood its whole life Turn Key Unit Ready to Work !!!!!

Morbark Chip Blower Hopper Feed Came out Running 10 HP Motor

2008 Morgan Single Head Resaw Can be purchased without Kohler diesel engine Could use replacement belt Runs and works good