BolDesign Kiln that includes Future-Design Controls FDC-2010-K5C Small Kiln Features • Board Feet Capacity: 2,000 to 10,000 BF (Board Feet) • Expect a 6-9 Week Turn Around • Easy to Clean and Maintain • Built with Aluminum and Stainless Steel, The Same Aluminum that is food grade used in Commercial Kitchens • RH control results in less lumber damage, this leaves you with better, brighter colors These Kilns are Built for Forklifts • Pallet Stock Drying Kiln; Disassembled crated and ready to load. 1 truck

Mechanical Pyramid Section Bending Machine Model # Z302 R-PR Voltage # 220/3 50/60

Brandt KDF 440C Edgebander

Brandt 1100 Edgebander Seller closed shop about 1 year ago and put this in storage. Claims they were using the machine up until they shut down.

Brandt KDN 770 2C Machine has been removed from service. Owner claims it is ready to run! Specs (to be confirmed): Hot Melt granulate quick heat-up glue system, overhead glue tank for easy maintenance & glue color change. Automatic magazine for strip & coil (large 800 mm dia. coil table to accommodate large coils of 3 mm PVC) stock, 3 mm PVC guillotine. (1) Drive plus (3) idle rolls "pneumatically controlled" pressure sections. End Trimming: 0.33 HP - 12,000 RPM Motors, chamfers 0° - 15°. Flush Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index pre-sets, (2) 0.5 HP - 12,000 RPM motors, cutter heads with insert knives. Fine/Radius Trimming: Top & bottom, bevels 0° - 15° with (4) revolver type index presets (0.5 HP - 12,000 RPM motors), cutter heads with insert knives for 3 mm PVC radius. 2 motor corner rounding Scraping Unit: Top & bottom for 2 - 6 mm radius, pneumatically controlled blowoff nozzles. Buffing Unit: Top & bottom buffing (0.25 HP - 1,400 RPM motors). Variable feed chain track speed from 8 - 20 MPM (26 - 65 FPM), 2 HP feed drive.

2022 Kiln-Direct Piggy Back Kiln New, Never Used 1999 53' Trailer

This Kimwood Panel Master Sander is in good working/running condition and it is ready to load! - 48" Feed - Feed speeds up to 200 lineal feet per minute - (2) opposing heads - 250HP - (2) operator control panels - Many spare parts including sanding belts

Double end automatic operation, for straight, right-angled work pieces Stock dimensions Stock length 220 - 2500 mm Stock width 15 - 200 mm Stock thickness 15 - 50 mm Double-sided trim saw: The saws are cutting downwards through the clamped work-piece.Each side 1 sawing unit. Horizontal drilling station: each side 1 drilling unit with 1 drilling motor 2 kW Distribution of vertical drilling units: 3 units at the front of the overhead beam 2 units at the back of the overhead beam

14@ x 16” inlet 16” Round inlet no motor

Komo VR508 CNC Router 60" x 120" Table 25 HP Sullair Vacuum Pump Dust Collector (10 or 15 HP - need to confirm) (2) Two main router heads with Quick Change (2) Vertical Drill Units (1) 8 HP 10" Saw Fanuc Control

Komo VR512 CNC Router Fanuc Controls SN 24129-03-01-93 Quincy Vacuum Pump

Kuka KR60-3 Robot System KR C4 Control System Kuka Programming Smart Pad Robot Enclosure (3) Heavy duty conveyor racks

LM Bump Rollcase Package Saw Includes waste conveyor under saw and elevated conveyor 550v/3 phase Approx 55" Bar Already dismantled and ready to load, as shown in the last two photos.

Laguna Bandt 4 Edgebander Machine is 6 months old Extremely low hours - Buyer upgraded to a larger machine!

1- 5mm Boring and Inserting Unit with Vibratory Hopper 1-8mm Boring and Inserting Unit with Vibratory Hopper Power: 208v-220v, 3 Phase, 30 Amps 96? Maximum Work Zone 4 zone stops 3-Axis Control For Positioning Weight 6,000lbs Solid One-Piece Welded Tubular Steel Frame Footprint (L x W x H): 135? x 45? x 82? Shipping Dimensions (L x W x H): 42.3? x 49? x 43? Shipping Weight: 7500 lbs

Hot Air Edgebander for Preglued banding 0.4 - 1.5 mm thickness Automatic cutoff for up to 1/32" Coil feed with manual feed for strips Panel thickness 10-50mm Front and rear end trim Top/bottom trim

LAMB 23x27 inch opening grinder with 150 HP motor, 1 3/8” screen and starter control. 460 volt 3-phase

Model # 01-1172-05-01 60” x 142” table size (1) available no hydraulic units or hand control

The robot arm can move the Layer Picker® in all directions, offering completely new application possibilities. With up to 8 picking or place positions the Layer Picker® Flex-R can be used for both picking for replenishment and batch layer picking at the same time. This means that the Flex-R solution can be used for pallet to pallet picks and negative picking as well. One machine – multiple applications

Leadermac LMC 418-S 4 head moulder 20-80 FPM feed spiral head on bottom 460 volt 3 phase