Giben WNAR6 Series Twin Pusher Angular Panel Saw Cutting length rip cut 3200 mm Cutting width cross cut 2200 mm Projection height 95 mm Lateral loading lift table with direct motorized infeed and right motorized infeed 2200 mm width interior panel turning station in the rip cut section Book aligners for both long and short rip stacks 17 material clamps Split pusher in the cross cut area

Ball Milling machine.

Shopbot CNC Router

Shurman Double Arbor Gang Saw 12" Capacity Thin Kerf Babbit Grinder

Model SF-45A 600 V / 3 Ph / 60 Hz 10ft table 8.5 HP main motor provides(2) cutting speeds 3,800 & 5,200 RPM

Silver Straight Line Rip Saw 15 HP Motor

Simonds Band saw leveler. Comes with pallet of spare parts.

4000# capacity 96” x 64” table size raised height 38-1/2" Lowered height 14-1/2" pneunatic operation Rotatable table 360 degrees safety skirts

PalletPal Spring Lift Table Specifications Load capacity 400 to 4500 lbs., depending on springs Load size .......50" wide x 50" long x 72" high (max.) Length 45 1/4 inches Width (base frame) 36 3/4 inches Compressed height 9 1/2 inches Extended height 27 3/4 inches Rotating ring, outside diameter 43 5/8 inches Rotating ring, inside diameter 40 5/8 inches Adjustment for sloping floors Can adjust for floor slope up to 1:25 using optional adjustable feet 4 Available

The seller has confirmed that this is in fair working/running condition and it is ready to load! - Cross cut panel saw

Speedaire Air Compressor 5 hp

STEFANI SOLUTION 8600 CNC EDGEBANDER CNC HORIZONTAL & VERTICAL POSITIONING, STANDARD STATIONS, PRE-MILL, ROUGH & FINE TRIM STATIONS, CORNER ROUNDING, MX80 HSK MILLING UNIT, RAS/S & RCA/2C SCRAPING UNIT, SP/F TOP & BOTTOM BUFFING EDGEBANDING THICKNESS: 0.4MM – 22MM PVC & ABS IN COIL OR STRIPS HPL STRIPS SOLID WOOD UP TO 22MM PANEL HEIGHT: 10 - 60MM (3/8” MIN – 2 3/8” MAX) MINIMUM PANEL LENGTH: 140MM (5 1/2”) MINIMUM PANEL DIMENSIONS: WITH MANUAL IN-FEED LENGTH WISE : WIDTH X LENGTH90 X 220 MM (3 1/2" X 8 3/4") CROSS WISE : WIDTH X LENGTH 220 X 135 MM (8 34" X 5 3/8") FEED SPEED: 12 - 25 M/MIN (40 - 82 FT/MIN) MINIMUM DISTANCE BETWEEN PANELS: 650MM (25 1/2”) (32” WITH CORNER ROUNDING) MACHINE WORKING HEIGHT: 950MM – 970MM (37.4” – 38.2”)

Automatic single sided edgebander designed to be used for edgebanding straight vertical profiles with coiled material (veneer and PVC) and with strips (high-pressure laminate and solid wood) with a maximum thickness of 12mm. Machine Base The machine base is a rigid, ribbed steel structure and is designed to provide maximum support for the working units. The ribs provide stability and, at the same time, provide openings in the base to facilitate removal of the chips/dust. Capacities And Speed Edgebanding thickness: .4mm - 12mm (.016-1/2”) Guillotine capacity: 3mm Feed speed: 33-66 ft/min. Panel height: 3/8” min – 2 3/8” max Minimum panel length: 5 1/2” Minimum panel width: 2” Minimum distance between panels: 24” Startouch Controller The Stefani KD comes equipped with the new "Startouch" controller. This controller features a 12" touch screen display. Capable of storing 100 programs, 6 at the touch of a single key. Color graphic display of all the working units.

Stromab Stromab TR350 Up Cut Saw 4 HP Motor (230v/3ph) Variable Feed Speed This was a demo machine. Ready to ship!

Stromab WS1 Cutoff Saw Thru feed system with defecting o cutting preset sizes - NO optimizing! Operator can mark the board with crayon. Demo unit with low hours!

Superfici Flat Line Will be removed from service by the end of January 2024. Still under power.

Manufacturer’s Specification - Maximum Width: 24” - Brush: 9"-11" Typical Diameter - Speed: Ranged Variable, 400-1200 rpm Brush - Motor: 5 HP, 220 Volt, Single Phase - has (1) broken caster

Runs good and is still in operation Hooked up to 460 Table Extension has been repaired Main table has almost zero wear on it.

Capacities: 11” minimum length 98” maximum length 1” minimum width 32” maximum width 5/8” minimum thickness 3” maximum thickness with a conversed glue spreader(model 30J)

10 HP 575 volt unit. Has between 25-27 CFM. RPM: 1745