Lico Rip System with 5-Moving Blades Includes: Infeed, tilt hoist, unscrambler, Lico infeed, 125 HP gang, outfeed tunnel, 75' sort chain Lateral Scanners High speed roller gang with (5) shifting blades: Up to 500 FPM Two Scanmeg scanners Singulating infeed Saw infeed fence Hogging blade to remove inside edging Outside edging falls off and into shredder New system upgrades in 2018

Year: 2006 Working Width: 25mm to 230mm (1" to 9") Working Thickness: 8mm to 120mm (0.31" to 4.72") Bottom Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Top Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 7.5kW (10 HP) Side Spindles (x2): 40mm diameter, 0-20mm transverse movement, 6000 RPM, 5.5kW (7.5 HP) Configuration: Bottom, Side, Side, Top, Top, Bottom Feed Motor: 4kW (5.5 HP) Elevation Motor: 0.75kW (1 HP)

Lobo 6-Head Moulder 9" Wide capacity

GB-CIS Single-end 575V / 3 Ph / 60 Hz 5” wide rubber pad conveyor Equipped with industrial motor for full power cutting and sanding capacity

Loewer Discmaster 6TD Brush Sander Vacuum Bed

Lower Denibbing Sander

MAC 114LST100 Dust Collector 12x10 Rotary Airlock Hopper and leveling screws Air flow: 18,000 ACFM Media: 2,000 sq ft 12 Gauge Carbon steel exterior Clean air plenum Guard rail Nema 4 enclosureHopper discharge to match airlock Magnehelic pressure differential gauge kit (100) 6" x 144" 16 oz Polyester bags 60 HP Motor, 460 V System has already been dismantled and is ready to load.

This system was purchased used and never put into service.

- Min. panel length 9.06 inch - Max. panel length 10 ft 5.98 inch - Min. panel width 8.27 inch - Max. panel width 4 ft 3.18 inch - Panel stack station - no. stations 1 loading - Max. panel stack height 5 ft 2.99 inch - Work capacity 13 Cycles/min - Lifting capacity 100 Kg - Panel stack infeed - Movement system with frame System suction cups - Vacuum pump - no. pumps 1 - Control system - PLC MAGELIS

Makor Start One M (S-ONE-M) Finishing Line Infeed & Outfeed System Storage Trolleys This line has been removed from operation and is in dry storage, as shown in the last (3) photos.

System includes: Vacuum Coater UV Oven with (9) lamps Lateral Transfer Table Max width 9" Able to run clear or pigmented coating

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

This Wood Drum chipper PT750 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, rubberized conveyor belt and Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. Width of inlet: 750 mm; • Height: 300 mm; • Rotor diameter: 800 mm; • Toothed roller: 03 upper and 03 lower; • Grooved rollers: 01; • Rollers gear motor: GD (helical gears); • Upper Rollers motor size: 7,5 hp (2x); • Feed speed: 35 m/min; • Number of rotor knives: 02; • Wood chip size: 25 - 40 mm; • Chipper screen: size: 70x 70mm; • Main motor 200 hp 4P: Included; • Drive panel: Included; • Estimated production: 65 m3 / h (it may vary according to the type of material and time used with blade sharpening); • Lead Time: 240 Days • Infeed conveyor length: 3 500 mm (included); • Width: 2 500 mm; • Height: 1.250 mm; • Overall length: 7 300 mm; • Approximate weight: 8 750 kg.

This Drum chipper is used in production of wood chips from logs and wood residues (slabs, board off cuts, veneer waste). It has a toothed driven roller system that allows an efficient infeed of the material, rotor with interchangeable thread locks and with a disposable steel plate in the front of the rotor, hydraulic nose-bar/anvil extractor, infeed conveyor with rubberized belt and hydro-pneumatic unit to lift the chipper/rotor lid. (maintenance). It comes with 01 set of blades and 01 nose-bar/anvil. Does not come with outlet conveyor. - Inlet width: 1000 mm; - Nominal chip size: 23 - 30 mm; - Inlet Height: 450 mm; - Main Motor indicated: 300 hp 4P (2x); - Rotor diameter: Ø 1000 mm; - Soft starter drive panel; - Shaft diameter: Ø 220mm; - Metal detector; - Toothed roller: 03 upper and 03 lower; - Estimated production: 130 m3/ h; (may vary according to the type of wood and the sharpening period of the knives); - Roller diameter: Ø 353mm; - Diameter of roller shafts: Ø 100mm; - Chipper Screen: 65 x 65mm; - Grooved roller: 01; - Infeed conveyor length: 5000mm (included); • Driven roller gearmotor: (helical gears); - Width: 3 500 mm; - Driven rollers motor: 15 hp (2x); - Height: 2 100 mm; - Main motor belt: Torque-Team; - Total length: 10 500 mm; - Inlet conveyor speed: 40 mL / min; - Approximate weight: 22 700 kg; - Number of rotor blades: 03;

Multirip circular saw for block cutting, with reinforced structure and high production speed. Trailed top and bottom rollers, upper rollers with adjustment, shafts with cartridge system for quicker and more efficient replacement of the set of saws, U-beam base with levelers and central lubrication. It does not come with the circular saws. - Maximum inlet width: 600 mm; - Minimum inlet height: 70 mm; - Maximum inlet height: 160 mm; - Double arbor: Ø 80 mm; - Number of saws per axle: 10x; - Exterior saws Ø: 350 mm interior saws - Ø: 110 mm; - Upper press rollers: 2x; - Bottom rollers: 6x; - Max. Feed speed: 35 m L / min for logs - 160mm above in diameter; - Max. Feed speed: 40-50 m L / min - only for logs 130-160mm in diameter; - Lower main motor indicated: 200 hp 2p (1x) Included; - Top main motor indicated: 150 hp - Main motor belt: 4 / 3v (8 Pcs); - Motor traction of the rollers: 5 cv 4p; - Gearmotor: GS (crown and pinion); - Length: 3366 mm; - Width: 2782 mm; - Height: 2233 mm; - Approximate weight: 5.470 kg

This is a Horizontal Band Saw Resaw Machine with Two saw heads. This is an ideal Machine for the recovery line, as it processes the slabs coming out of the Vertical Twin band saw machine “the resaw process”. It comes with an input chain conveyor, driven press rollers. Cutting Height and saw blade tensioning setting system. It also comes with main motor, motor drive panel, the Frequency inverter, gear motor drive panel. It does not include the saw blade. - Wheel blade: Ø1000mm; - Wheel blade width: 5"; - Maximum wood width: 400 mm; - Maximum wood height: 380 mm; - Minimum length of wood: 1250 mm; - Single Input table/ conveyor width: 600 mm; - Motor press roller: 1 cv 4P (2x); - With two independent infeed rollers; - Forward speed: 45-50m / min for small logs; - Main motor indicated: 2 x 60 hp - Soft starter Drive panel: included; - Servo motor thickness setting system (INCLUDED); - Main transmission belt: 3 x Channel B; Length: 6.532mm; - Width: 2.220mm; - Weight: 7655kg.

Vance PT600R8 Drum Chipper See this machine at IWF Atlanta 2024! This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

Vecoplan RG 42/60 XL 60 HP Motor 15" Rotor 42" x 52" Hopper Opening 1" Screen This machine went through a rebuild. It was not big enough for the buyers application. Available immediately.

This Grinder was recently taken out of service and was running good. No electrical controls. Ready to load.

This Grinder was recently just taken out of service. It ran very good before taken out. Does not include electrical controls.