MAT Drill System Infeed Trim Saw Drilling Outfeed

Spray booths - (3) Available Approx 15'x12'

4' x 6' Table Hand controller ____ capacity

Table Top Measures 50x50 Hand Operated Air Valve To Raise & Lower Lower Height is 12 1/2 Total Raised Height is 27 1/2 All Air Operated 4,000 lb Capacity

2000 lb Scissor Lift Table Good Condition

75 HP 550 Volt 3 phase

15 HP 460 volt 3-phase 63 CFM Capacity

USNR 60,000 Board Foot Kilns (10) Available

Vac-U-Clamp FT900 Thermafoil mPress Brand new - Seller never used it!

Vac-U-Clamp FT800+ Thermofoil Press 52" x 105" Work area Dispenser Rack (3) Vac bags new in boxes still

The Vantec 2800mm Spindleless Veneer Lathe is designed to process veneer for plywood production from both hard and soft logs. Its metal tempered grooved rollers and lathe knife inclination system work perfectly to make sure there will always be a precise contact area between the lathe knife and the log during the peeling process by eliminating vibration that could cause damage to the Veneer sheets. Vantec Spindleless lathe proves its efficiency by delivering consistent thickness variation and a impressive top linear speed of 180 m/ min throughout the peeling process for face or core veneers with smooth surfaces. - Log diameter up to 600 mm; - Max log length: 2750 mm; - Min log Length: 2300mm; (with stacker) - Min log length:1800mm (no stacker); - Veneer thickness: 1.0 to 4.0 mm; (Pine and eucalyptus); - Log core after peeling: 40 to 45mm; - Maximum linear speed 180 m/min; - Drive panel included; - Each motor is individually connected by a Variable Speed Drive for torque control in two points of traction on the rollers to pre- vent excessive load on tip ends; - Log Central aligner with maximum of 2200 mm of movement; - Pneumatic scriber Knives (02 fitted on the sides to cut in width and 01 in the Center to cut the length); - Width: 7640 mm; - Length: 3400 mm; - Height: 2550 mm; - Approximate weight: 14000 kg.

The Vantec Automatic Rotary clipper is designed to clip 2800 mm veneer sheets into specific sheet sizes as per the auto stacker preselection. It comes with electronic drive panel, automatic gauge system, positioning of clipper knife by Servomotor and encoder. It is de- signed to work with one tensioned clipper knife with gear motor. It also comes with a 2 HP motor on the output. The clipper knife is not included. - Veneer Thickness : 1 to 4 mm; - Max. Log: 2.750mm; - Minimum veneer width cut: 800 mm; - Max. Veneer length cut: 2700 mm; - Min. Veneer length cut: 700 mm; - Min. Venner rounding length: 150 mm; - Rotor gear motor: helical gears; - Clpper rollers power drive: 4 hp 6P; - Outlet conveyor Motor: 2hp 4P (input) 1 hp 8P (output); - Clipper Servomotor: 40 Nm (2x); - Width: 4800 mm; - Length: 6000 mm; - Height: 1700 mm; - Approximate weight: 7.000 kg

The Vantec Veneer Auto Stacker, ELV 1.82B is a Vacuum stacker for 2800 mm Veneer lathe. It is fitted with double stacking system (04 bins), with four veneer transport lines and four 5hp exhausters. with of two stoppers and eight ejecting arms. With drive Panel, VSD for exhaust fans and hydraulics lifting tables. Min veneer sheet length sheet: 2300 mm; • Max veneer sheet length sheet: 2700 mm (or Two sheets of 1350mm); • Min veneer sheet width: 800 mm; • Max veneer sheet width: 1500 mm; • Max height of stacks: 1000 mm; • Exhaust motor: 10 hp 4P (8x); • Inlet conveyor motor: 2hp 8P; • Transport conveyor motor: 6hp 4P; • Hydraulic pump motor: 5hp 4P (3x);

Weeke BHP 007/430 CNC Router 13 HP HSK 63F Spindle with air blast nozzles 8 Position Rack Style ATC 7 Spindle Boring Block 4x8 Table Part location pins (2) Becker 7 HP vacuum pumps Woodwop Light Barrier safety system

Weeke BHP 007/430 CNC Router 13 HP HSK 63F Spindle with air blast nozzles 8 Position Rack Style ATC 7 Spindle Boring Block 4x8 Table Part location pins (2) Becker 7 HP vacuum pumps Woodwop Light Barrier safety system

The Vantec Wood Wast Drum Chipper is used to produce chips from logs and veneer waste. It has a roller infeed system, rubber conveyor belt and hydro-pneumatic unit to lift the rotor for maintenance. Manufacturer specs: - Width of inlet: 600 mm; - Height: 200 mm; - Rotor diameter: 600 mm; - Toothed roller: 01 upper and 02 - lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical - gears); - Upper Rollers motor size: 5 hp; - Upper Rollers motor size: 5 hp; - Feed speed: 40m/min; - Number of rotor knives: 02; - Wood chip size: 30 - 40 mm; - Chipper screen: size: 65 x 65mm - Main motor 100 hp 4P: Included; Drive panel: Included; - Estimated production: 38 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 650 mm; - Height: 1 .000 mm; - Overall length: 5800 mm; Approximate weight: 2,900 kg.

Castaly Chop Saw and End Feed Model CS-24L 440V 3 ph

MANUFACTURER SPECS: 2000 C.B. LEVIGATRICI 52" DUAL HEAD WIDE BELT SANDER. 1ST HEAD: 12" SPIRAL RUBBER ADJUSTABLE HEIGHT CONTACT DRUM. SECOND HEAD: DIGITAL PLATEN. VARIABLE SPEED EVERYTHING. LONG BELT LENGTH OF 103". OSCILLATING BELT BLOWERS. VARIABLE SPEED EVERYTHING. DIGITAL POSITIONING. 220 volt 3 phase. includes 18 spare belts…approximately half new, rest lightly used.

Maximum workpiece height mm. 320 Maximum workpiece width mm. 320 Minimum workpiece length mm 700 Brush diameter mm. 160 Brush rotation adjustable with inverter rpm 0 – 1400 Blower motor power under inverter kw 4 Brush motor power under inverter nr. 4 x kw 0,55 Work speed adjustable with inverter mt/1’ 8 - 45 Feeding motor power kw 1,1 Electrical system MACHINE DIMENIONS: Volt 380± 5% Lenght mm 3350 Width mm 1350 Height mm 2350 Machine weight kg 1150

Cefla Sorbini T/20-3-STP Triple Head Print & UV Line (3) Print Head System (2) IR Ovens Available Immediately