44 ft. long x 96 in. wide variable speed belt conveyor, 2HP 480V electric motor Belt is approximately 90" wide

4 banks of 15 fans as pictured

B&C 8' Shaving Mill: 3-Heads, 50 HP each, Infeed log deck, 8" heads with 8-rows of knives Outfeed conveyors to drum and stacking room 8'x24' Heil Triple pass drum dryer Jackson Webb Burner

6x6" capacity 15hp 480 volts

14" chop saw with 5 stops 70" table 5HP single phase 220v electric motor

3 Belt Conveyors Available: 1. 52 ft long, 42" wide, 36" belt 2. 31 ft long, 42" wide, 38.5" belt 3. 51 ft long, 42" wide, 38.5" belt

This wood was all removed from an old mill on South Carolina. It is ready to be loaded out.

Table Top Measures 50x50 Hand Operated Air Valve To Raise & Lower Lower Height is 12 1/2 Total Raised Height is 27 1/2 All Air Operated 4,000 lb Capacity

10 HP Dust Fan with ductwork 230/460 volt 3-phase

Dimensions are 19'4"x14'7"x18'2" Gas fired with Maxxon

Roll Case Conveyor

Chain Conveyor Lumber Deck

This unit was blowing dust to a large baghouse in a large facility. There is also a 75 HP blower and baghouse available at the same location. Piping is available. Unit will be loaded on the truck.

75 HP 550 Volt 3 phase

15 HP 460 volt 3-phase 63 CFM Capacity

USNR 60,000 Board Foot Kilns (10) Available

3 Guide Milling Machines Good Working Condition Stands Included

Vance PT600R8 Drum Chipper See this machine at IWF Atlanta 2024! This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.

The Vantec Wood Wast Drum Chipper is used to produce chips from logs and veneer waste. It has a roller infeed system, rubber conveyor belt and hydro-pneumatic unit to lift the rotor for maintenance. Manufacturer specs: - Width of inlet: 600 mm; - Height: 200 mm; - Rotor diameter: 600 mm; - Toothed roller: 01 upper and 02 - lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical - gears); - Upper Rollers motor size: 5 hp; - Upper Rollers motor size: 5 hp; - Feed speed: 40m/min; - Number of rotor knives: 02; - Wood chip size: 30 - 40 mm; - Chipper screen: size: 65 x 65mm - Main motor 100 hp 4P: Included; Drive panel: Included; - Estimated production: 38 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 650 mm; - Height: 1 .000 mm; - Overall length: 5800 mm; Approximate weight: 2,900 kg.

This Wood Drum chipper PT600 is used in production of wood chips from logs and veneer waste. It has a toothed roller system that allows efficient material infeed, a rubberized conveyor belt and a Hydropneumatic unit to lift the rotor cover for maintenance. It comes with 01 chipper Knife set and 01 nose bar set. It does not come with the output conveyor. - Width of inlet: 600 mm; - Height: 300 mm; - Rotor diameter: 800 mm; - Toothed roller: 01 upper and 01 lower; - Grooved rollers: 01; - Rollers gear motor: GD (helical gears); - Metal detector: Flat model; - Rollers motor size: 5 hp (2x); - Number of rotor knives: 02; - Wood chip size: 25 - 40 mm; - Main motor 125 hp 4P: Included; - Drive panel: Included; - Lead Time: 240 Days; - Estimated production: 55 m3 / h (it may vary according to the type of material and time used with blade sharpening); - Infeed conveyor length: 3 500 mm (included); - Width: 1 850 mm; - Height: 1 .150 mm; - Overall length: 6 700 mm; - Approximate weight: 4,900 kg.